Search Documents

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By Jochen Petersen, Caroline Muzawazi

The technical feasibility of ammonia leaching of PGM bearing Platreef flotation concentrates was investigated as an alternative method for the recovery of base metals prior to precious metal recovery. The composition of the concentrates includes 2.02% Cu and 3.17% Ni, and the major base metal minerals are chalcopyrite and pentlandite. Optimal leaching conditions were initially established in shake flask experiments to be a solution containing 4 M NH4OH, 4 M (NH4)2CO3 and a pH range between 9 and 10. These were used as base case conditions in column and batch stirred tank reactor tests, where the effects of total ammonia concentration and operating temperature were explored further. At optimal conditions nearly 100% Cu and Ni extraction were obtained in the batch stirred tank reactor, and 95% Cu and 60% Ni extraction was obtained in columns. The activation energy for chalcopyrite and pentlandite was 36 kJ/mol and 16 kJ/mol, respectively, in both reactors, indicating different reaction pathways for the two minerals. Gas-liquid mass transfer appears to be the limiting reaction step in columns much more than in tanks, and the degree of ammonia loss to air is significant. This initial test work indicates the feasibility of using ammonia leaching for this and similar materials as an alternative route to conventional smelting and refining prior to PGM recovery, but a number of technical challenges still need to be overcome.

Jan 1, 2014

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By R. G. S. Mussi

An inclined cooling plate is utilized as a modification in the compocasting process of magnesium alloy and the mechanical properties of the composites obtained are studied in this work. Based on crystal separation theory, molten AZ91D is poured onto an inclined plate in order to produce solidification nuclei inside the fluid metal, and is mechanically stirred while reinforcement is added. Particulate SiC was utilized as reinforcement in quantities varying from 0 to 15%vol. Dispersion of the reinforcement was observed by macro and microstructure analysis. SiC was properly mixed into matrix until 15%vol., and Vickers hardness tests were carried out for the composites produced. Results obtained for hardness were shown to increase with reinforcement addition and comparable to those of traditional compocasting. Utilization of Inclined Cooling Plate produced good inclusion and homogenization of SiC through an AZ91D matrix, at lower temperatures and shorter times than traditional compocasting.

Jan 1, 2006

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By R. Cammack

"A fundamental component of the Hoek–Brown empirical rock failure criterion is assessing an appropriate mi constant. In developing their empirical criterion Hoek and Brown normalised triaxial test results by dividing the principal stresses at failure by the uniaxial compressive strength to provide mi values for typical rock types. Experience shows that Hoek triaxial tests for individual lithology types commonly have a large inherent scatter. In addition, tests are often conducted on core from random locations, which although being of one parent rock type, display variations in density as well as minor variations in grain size and alteration.This paper presents experience from projects the authors have been involved in which large sample populations of triaxial and UCS tests on similar rock types were available. Geophysical logging data was also available for some projects. The methods used to estimate the compressive strength for each sample and the effects on normalising the data sets are described. The variability of the data and uncertainties and assumptions involved in the process of assigning a mi value from the normalised data are also discussed."

Jan 1, 2015

By John J. Laffin

"Nova Scotia Department of Mines and Energy Throughout the history of Nova Scotia, trends in the production and use of its coal resources have resulted in major impacts on the economy and society of the province. Current trends in coal demand locally, nationally and internationally are having and will have an increasing positive effect on Nova Scotia over the next twenty years-in terms of energy supply, job creation and general economic development. Coal for electrical generation is an immediate and key objective of Nova Scotia's energy plan; and, in the long term, coal-derived fuels will meet the province's needs for transportation fuels. Demand for metallurgical coal is also expected to increase, especially if the merchant coke plant currently under investigation becomes a reality.Meeting these coal supply and utilization objectives in the face of increasing environmental, social and economic constraints poses a tremendous technical challenge. Work has begun on projects to expand coal production capacity and to adapt new technologies for coal preparation and utilization to the specific needs of Nova Scotia; much more work will be required in the coming decade in order to succesfully tap this resource.IntroductionThe energy problem facing Atlantic Canada has a few unique features not found in the rest of the country. Canada, as a whole, has access to a diverse mix of energy resources, including crude oil, natural gas, coal, hydro and uranium, with the result that crude oil supplies only about 40 per cent of Canada's primary demand. In contrast, foreign crude oil dominates Atlantic Canada's energy mix, supplying over 70 per cent of the primary energy demand.This results in important differences in various sectors. Nationally, about 5 per cent of the electricity is generated from oil whereas last year in Nova Scotia approximately 40 per cent of the electricity generated was from imported oil. Residential, commercial and industrial space heating, and industrial process heating in Atlantic Canada was almost 100 percent dependent on foreign oil. This is in sharp contrast to the situation in central and western Canada, which have access to secure domestic natural gas, oil and hydro electricity."

Jan 1, 1982

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structurallife often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response and a simple estimate of structural life for haulers.

Jan 1, 2011

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By Peter Broad

"Extracting any metal, especially specialty metals and rare earth elements, requires an in-depth analysis of the costs and potential revenue as well as a due diligence study of other stakeholder interests. Rare earth projects are generally in the billion dollar US range or above, and thus failure to accurately predict any loss of revenue caused by impurities within the product or additional effluent treatment costs can destroy an otherwise viable study. Two prime sources of input impurity are considered: impurities in the material feed and from reagents. The effect of these impurities factor on both the product (in reduced revenue) and on residual “tailings” that may incur additional unforeseen costs.INTRODUCTION“Truth passes through three stages. First, it is ridiculed. Second, it is violently opposed. Third, it is accepted as being self-evident” – Arthur SchopenhauerThe era of unscoped, unbudgeted construction ended about 150 years ago. Today’s engineer must design with confidence; but do so amidst proprietary secrets and unfamiliar pollutants, which present a myriad of interesting challenges. Is it possible to build a viable rare earth plant to a realistic budget, without destroying that which we cherish? Some see this as contradictory but in reality it is the only viable option.WHEN GOOD PROJECTS FAILWithout rare earths the Copenhagen agreement might be null and void. Running a wind turbine with a 30 tonne conventional magnet requires some hefty engineering and prohibitive investment. Despite their ‘Green metal’ applications, production of rare earths have created environmental nightmares, as Folger stated in 2011 when visiting Baotou, or has Jaing Mainheng who has been quoted by Ambrose Evans-Pritchard 6 Jan 2013. This comment is not a criticism of China; the details are from a 2012 white paper published by the Chinese Government that initiated a $6 billion environmental clean-up. Nor is China unique; other plants have had problems as well. There were toxic leaks in the 1990s from Mountain Pass, and the Mitsubishi Bukit Merah Plant (built in Malaysia in 1958) required a $100 million clean-up."

Jan 1, 2016

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By M. L. Wacker

"Cigar Lake high-grade uranium mine in Saskatchewan is operating after 25 years of test mining, construction, and mine flood remediation. Factors include ground stability, groundwater control, radiation exposure, and ore handling. A 10 year test program resulted in validating “jet boring”, a non-entry mining method involving artificially freezing the orebody and surrounding rock; tunnelling to develop access crosscuts below the orebody; installing cased pilot holes through ore; extracting ore using rotating high-pressure water jets within pilot holes; and cavity concrete backfilling. Ore slurry is prepared underground, pumped to surface, and trucked to McClean Lake mill for processing to uranium concentrate.RÉSUMÉ Après 25 années d’essais sur les méthodes minières, de construction et d’assainissement suivant les inondations à la mine, l’exploitation de minerai à haute teneur en uranium Cigar Lake, localisée dans la province de la Saskatchewan, est opérationnelle. Les principales difficultés concernent la stabilité du terrain, le contrôle des eaux souterraines, l’exposition aux rayonnements et la manutention du minerai. Un programme d’essai de 10 ans a abouti à la validation du « forage à érosion », une méthode minière qui consiste à congeler artificiellement le corps minéralisé et les roches environnantes ; à creuser des tunnels pour développer des travers-bancs d’accès en dessous du corps minéralisé ; à installer des puits de fondation pilotes à travers le minerai ; à extraire le minerai à l’aide de jets d’eau à haute pression dans les puits pilotes ; et à remblayer les cavités avec du béton. La boue de minerai est préparée sous terre, pompée vers la surface puis transportée par camion jusqu’à l’usine de concentration de McClean Lake pour le traitement afin d’obtenir du concentré d’uranium.INTRODUCTIONThe Cigar Lake deposit is in northern Saskatchewan, 660 km north of Saskatoon, Saskatchewan, Canada, at the east edge of the Athabasca basin (Figure 1; Bishop, Mainville, & Yesnik, 2016). The operation is jointly owned by Cameco Corporation, AREVA Resources Canada Inc., Idemitsu Canada Resources Ltd., and TEPCO Resources Inc. Cameco has been the operator of Cigar Lake since January 2002. The discovery hole was drilled in 1981. Commercial production was declared in May 2015 and the Phase 1 operation will have a mine life of 15 years."

Jan 1, 2017

By T. Velea

The most widespread methods for producing metallic copper are smelting of copper sulphide concentrates (which generates various types of polluting substances) and the hydrometallurgical route which consists of leaching in sulphate and chloride media (usually employing high temperature, high-pressure and special equipments). This paper presents a process, called VEPE, which consists of oxidizing copper sulphide concentrates in weak alkaline media (Na2C03 orland NaOH solutions), under low pressure and with air sparging. The oxidized concentrate contains less than 0.4% S. Copper is recovered from the oxidized concentrate by the standard leaching-solvent extraction-electrowinning route, with a total efficiency of 98% extraction. The proposed technology could represent a good opportunity to recover copper from sulphide concentrates in a clean, simple and profitable way.

Jan 1, 2007

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012

By C. J. Havard, G. C. Taylor, D. G. Cook, N. C. Ollerenshaw, D. K. Norris

"The area encompassed by this report is the eastern and northern Cordillera, shown on the composite map accompanying these background papers. It extends from the 49th pm•allel to the Arctic Ocean and from the Rocky Mountain and Tintina trenches to the Interior Plains. The Mackenzie delta is included in the discussions because of the implications of the bedrock geology of the Arctic Plateau and Coastal Plain on the hydrocarbon and mineral potential beneath it.The eastern and northern Cordillera forms the back-bone of the Western Canada sedimentary basin and from it most of the principles of orogenesis and epeirogenesis relating to the understanding of the structural, depositional and fossil record of the basin have been derived. It may be divided roughly into two parts, reflecting basic differences not only in structural style but also in mineral potential. The more easterly and younger rocks generally contain hydro-carbons, coal and non-metallic minerals; the more westerly and older rocks contain metallic and industrial minerals."

Jan 1, 1970

By R. Brough

"Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind - and Secondary Hills. There are, however, only a few Primary Hills in operation with ""solid"" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a Cost per ton basis and/or downtime for liner replacement would be to a high.In other words, solid rubber has limits as any other material. However, 'SKEGA started to think, why not try to use the best properties of rubber as well as steel and combine the two materials together.Nearly 10 years ago SKECA started to test this concept in Rod Mills. A steel cap was vulcanized on to the leading face of the lifter bars, to be installed close to the feed end head (fig. 1)."

Jan 1, 1988

By Magnus Evertsson, Johannes Quist

HPGRs have since introduced in the 1980s (Kellerwessel, 1993; Schönert, 1988), now become integral comminution units at several minerals processing plants around the world. Even though a lot of the initial issues concerning performance, availability and wear have been addressed and solved there are still phenomena and aspects which can be improved and understood further. Schönert and Sander (2002) presented experimental results and a mechanistic model including the internal force dynamics between the rollers and the compacted bed. They derived expressions for the pressure distribution involving most of the influencing terms and effects. However, in order to solve the differential equations several of the terms vanish by assumptions. The Schönert and Sander model reflects the experimental data in many aspects but the predicted shear force distinctly deviates from the experimental results at the angular position of the peak pressure level. This finding suggests that the particle to particle interaction and breakage process in the different zones seen in Figure 1 are complex and difficult to model using analytical models. A numerical modelling approach using DEM does not require the same amount of assumptions and simplifications of boundary conditions. Hence such modelling may provide further knowledge and vital understanding. In this paper the breakage process is simulated in order to investigate the shear slip behaviour and how it relates to different operating variables. A laboratory scale HPGR corresponding to the experimental setup used by Schönert (2002) have been modelled in EDEM (DEM-Solutions). The bonded particle model (BPM) is used for modelling quartz particles (Potyondy, 2004). The breakage model strength parameters are calibrated against interparticle breakage experiments in an Instron 400RD compression device. The contact model parameters are calibrated using calibration methods developed by Quist (2015). The floating roller dynamics are modelled using a spring-damper system. Results present insights regarding the interparticle slip behaviour as well as the frictional tangential force distribution on the rollers. The simulated roller pressure distribution shows good correspondence with previously reported findings in the literature.

Jan 1, 2016

By J. F. K. Brown

WHEN I first received the kind invitation extended to me by the Mining Society of Nova Scotia, I read over very carefully the suggested title-"The importance of long-distance planning and budgetting in modern methods of mining, and the advisability of working to some definite plan". I came to the conclusion that I might as well confess my inability to handle properly such a vast and intricate subject within the scope of any one paper. More properly, I think a round-table discussion should be indulged in-a sort' of symposium carried on in similar fashion to the World Power and Coal Conferences- you know, a committee for this, a committee for that, and, finally, a committee to see what the committees are doing. Weil, your Secretary's suggestion is just like that- much too comprehensive for any half-hour's presentation. As a paper, also, it either becomes too general and therefore uninteresting, or i.t descends into detail and describes means and methods to the end desired, which have little attraction because they were designed to meet quite different conditions than those my audience would mentally be considering. Of the two evils facing me, I have chosen the one that sticks to the generalities. Your Secretary's query almost automatically divides itself into two distinct phases: First, the importance, and second, the advisability, of planning. Let us dwell for the moment on the second, because, if we can prove advisability, that leads to desirability and, finally, to doing. Proving is the difficult part of the little problem. Here was something I, personally and as a mining engineer, had been battling for all my corporate life without being able to prove it to anybody. Then I saw the way out of that. I perceived I could put that little question of advisability on another basis altogether-:put it in the class of "coming- some day- soon" whether you or l or anybody else liked it or not; call it, if you please, mandatory, certain, necessary, enforceable planning. All of which means that the problem of advisability has rather suddenly become the very practical one of "how to do it". Why?

Jan 1, 1937