Search Documents

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By F. H. Samuel, H. Tahiri, S. Valtierra, H. W. Doty, A. M. Samuel

L'affinage des grains dans les alliages d'aluminium consiste à augmenter le nombre de sites de cristallisation de la phase a-Al afin d'obtenir une structure fine. Les alliages mères de type Al-Ti-B sont largement utilisés comme raffineurs des grains. Cette étude a pour but d'établir des mécanismes convenables d'affinage des grains dans l'alliage A356 en utilisant cinq alliages mères et deux températures de coulée (750°C et 950°C). Les résultats montrent que la phase a-Al prend une forme selon l'alliage mère ajoute; les échantillons coules a haute température montrent une taille de grain plus grosse; les températures de germination et de croissance augmentent avec I' augmentation du Ti ou du B et la taille des grains diminue. L'alliage mère Al-4%B montre une puissance remarquable en comparaison d'autres alliages mères. Pour cet alliage mère, le titane résiduel dans l'alliage A356 réagit avec le bore pour former TiB2 qui, par la suite, agit comme un germe actif pour la phase a-Al.

Jan 1, 2006

By G. Dörsam, M. Spreij, S. J. Van der Wal, A. P. Schmidt

The transfer of hot metal desulphurising from the torpedo cars to the hot metal ladles at the IJmuiden BOS plant no.2 caused a decrease in ladle lining life from 680 to 470 heats. Changing the desulphurising agent CaC2 for CaO during a trial period, for environmental reasons, led to a further decrease in refractory life. Availability of the ladles became critical and the major reasons for the low life were identified. Solving one of them, temperature, quickly resulted in restoration of the original lives. However, re- introduction of the new desulphurising agent on 50% of the heats again resulted in a decrease, this time from 700 to 550 heats. In order to be prepared for the full introduction of the new agent, thorough investigation of worn linings was conducted, revealing the major (chemical) wear mechanisms. With these findings, a new design for the hot metal ladle is proposed.

Jan 1, 2004

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By K. Purazrang, P. Sh. Naseri, P. Abachi

In present work, the comparative measurement of aluminum alloys' resistance to the unstable fracture was provided. Besides, the rupture mechanisms of high strength 7075 and 7050 aluminum alloys were investigated. The specimens were used as solution treated, quenched and aged condition. The elastic-plastic behavior of specimens was determined by carrying out tensile test on cylindrical specimens. The small sized specimen with 6.35 mm thickness and V-notched radius less than 60 µm was used for evaluation of damage properties, in accordance with ASTM B871-96 standard test method. All tear specimens were machined in L-T orientation. The mechanical tests were conducted at RT on an universal Instron machine under cross head speed of 0.1 mm/min. The results of mechanical tests made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. The comparison of specimens' resistance to crack propagation and unstable fracture due to the presence of crack-like strain concentrator was provided using tear test data. The microstructure of specimens was studied under optical microscopy. The rupture micro-mechanisms were analyzed by examination of specimens fracture surfaces using SEM. The microstructure examination indicated almost equiaxed grains on the transverse directions and elongated grains on rolling direction. Moreover, intermetallic particles were evident at microstructure. Considering the SEM fractographs, it seems that the intermetallic particles act as void nucleation and damage initiation sites. However, the damage mechanism of tensile specimens and severely notched specimens, especially near the notched root differs due to stress and strain states.

Jan 1, 2006

By Brian Putland

Single stage semi-autogenous / autogenous (S/AG) milling has become a common design for a variety of ore types with the advantages of being comparatively low capital cost and flexible for future expansion. The single stage SAG/AG milling option is ideal for starter projects with significant exploration and expansion potential. Currently a number of the largest SAG mills designed are installed in single stage configuration. This paper discusses the challenges associated with the process design of single stage SAG/AG milling circuits, the design flexibility required to ensure a robust circuit and the operating techniques adopted at successful installations.

Jan 1, 2012

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By J. O. G. Posada

Magnesium derived foams were prepared by using the so-called baking of powder blended precursor material method. This method comprises mixing magnesium powder with a small fraction of blowing agent (ZrH2, Cs2CO3 and CaH2) and Ni like catalyst, compacting this mix and creating a foam by heat treatment above the magnesium melting temperature. The resulting samples were characterised by microscopy, gas adsorption (BET method) and by small angle neutron scattering. Several mathematical models were used in order to determine particle size distribution, fractal dimension and total pore volume fractions.

Jan 1, 2005

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By R. Mohan Srivastava

"The goal of estimation is considered in the light of decision analysis. A simple example reveals the essential elements of decision-making in the face of uncertainty. A second example shows that these elements are also key features of many mining decisions. These two examples cause us to revive an old probabilistic notion that the goal of estimation should be to quantify what is unknown. The conditional probability distribution provides the complete statement of one's uncertainty. Once the conditional probability distribution has been established, one should retain as an estimate the value which minimizes some objective loss function. A third example shows how the ""best"" estimate depends on the chosen loss function. Current practice is almost exclusively based on the least squares method, which assumes a loss function which penalizes underestimation and overestimation equally. This is unfortunate not only because symmetry is an unrealistic assumption but also because mining offers a rare opportunity to state the loss function directly in terms of profitability. Both the theoretical framework and the practical tools exist to allow us to reconsider the conventional notion of the ""best"" estimate. IntroductionThis paper looks at estimation in the mining industry from the point-of-view of decision analysis. Virtually all decisions depend on estimates since few of the important parameters are ever known exactly. In this paper we will be referring mainly to the estimation of ore grades, though the approach discussed here is generally applicable to any decision in which relevant information is uncertain.In the first section we look at a very simple example of decision-making in the face of uncertainty. We will then tum to a mining example and see that the essential features of the simple example still pertain. From these two examples it will be clear that the decision analysis approach rests on two key concepts: the conditional probability distribution and the loss function. A third example demonstrates how different loss functions produce different ""best"" estimates from the same conditional probability distribution. In the final sections we willexamine the current practice of estimation in the mining industry. Though the tools for estimating the conditional probability distribution already exist, a change in the way we think about ""best"" estimates is needed. Very little attention is presently paid to the loss function even though it is readily available in many mining applications."

Jan 1, 1987

By R. MacRosty

The demand to increase production levels in smelting furnaces has driven the increase in the power levels. Consequently, greater cooling capacity of the furnace shell has been necessary, resulting in the widespread use of water-cooled elements to protect the refractory linings. Since water ingress into the furnace is an explosion hazard, monitoring and maintenance of the water-cooled elements is of key importance. Some of Hatch's recent research and development efforts have been focused on methods to provide an increased level of monitoring of water-cooled furnace elements; this paper focuses on two technologies developed for this purpose. The first involves the installation of a fibre optic temperature sensor in a water-cooled tapblock. The sensor is capable of providing high accuracy temperature measurements with a fine spatial resolution throughout the tapblock. Hatch has already developed a diagnostic system that uses multivariate statistical analysis to interpret the large quantities of data generated by the sensor. A second technology under development is concerned with enhancing the operating integrity and safety through detection of leaks in the water circuits. A successful leak detection strategy requires minimal maintenance and the ability to detect minute leaks. An instrument that meets these criteria has been investigated and is currently under development. This paper focuses on the technology and results from the test work that has been completed to date.

Jan 1, 2007

? Founded In 1953 ? Mining growth of 83% since 2007 ? We produced over 1 million ounces of Au in 2012 ? We Forecast of 20% Au production in 2013-2015 ? We have paid a dividend 31 years consecutively. Terry Reid ? 1992-93 Electrical Technical, College ? 1994-95 On the job placement College ? 1998 ? Licensed Millwright, ? 2005-12 ? Maintenance Reliability Planner ? 2012- Present Business Process Owner

Aug 1, 2013

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By R. C. Wallace

Introduction At a time when the mineral-bearing areas in Manitoba are being fi very keenly explored because of the major developments which are now taking place in that Province, it may be timely to give an analysis of the mineralization in the two major types of deposits, with a view particularly to assist in the intensive prospecting to which the mineral-bearing areas in the Province are now to be subjected. As is already well known, there are two principal types of mineral deposits in the territory- copper-zinc and gold; and attention will be confined almost exclusively in this paper to these two types, with some indication of such modifications of the main types as may be found to be of economic value. The details of the paper are drawn from what is yet a small part of the area of the Province available for prospecting. Enough is now known of the types of mineral deposits which are described in the following pages to justify the expectation that these types may serve as criteria in the search in the newer districts. Doubtless new types will also be found as investigations proceed.

Jan 1, 1928

By Mark Aylmore, Guy Deschenes

"Increasing pressure are motivating the gold mining industry to develop a substitute to cyanide for leaching gold. This effort in mainly based on the high toxicity of cyanide and on the lack of efficiency of cyanide in the treatment of mildly refractory gold ores (sulfides and pre-robbing). Consequently, in only a few years, consortia have been created to elucidate and implement a new technology. The most promising lixiviant that has been selected to replace cyanide is thiosulfate. This paper will present a critical analysis on the latest developments in thiosulfate leaching and illustrate the potential and limitations of the technology with experimental data. Finally an assessment of the cost and performance of thiosulfate leaching relative cyanidation will be evaluated.INTRODUCTIONConcerns regarding the toxicity of cyanide and inability of cyanide solution to effectively leach some carbonaceous gold ore or mild refractory gold ores have made the gold mining industry evaluate alternative lixiviants to leach gold. This concern has been heightened recently by the cyanide spill at a mine in Romania, which devastated a 250-mile stretch of the Danube River and its tributaries, and the environmental damage at Ok Tedi mine in Papua New Guinea. Some countries and locations have prohibited the application of cyanidation to recover gold, such as, California and Colorado States, Japan and Turkey etc.There are several potential non-cyanide lixiviants (Sparrow and Woodcock, 1995) for gold extraction, such as thiosulfate, thiourea and halogen. A pilot feasibility test (Marchant and Broughton, 1987) had suggested that thioureation might result in acutely toxic byproducts even after treatment. Scientists of Swedish Academic of Sciences reported that thiourea is a carcinogen. Halogen is also a pollutant to the environment. Thiosulfate leaching appears to have very good potential as an effective and less hazardous procedure for gold and silver extraction from auriferous ores. In addition to being much less toxic and relatively cheap, it forms a stable anionic complex with gold but is less reactive to other metals, for instances, copper and carbonaceous materials, in comparison with cyanide."

Jan 1, 2001

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969