Search Documents

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By Edward Rybinski

Compañía Minera Antamina is a polymetallic mining complex that produces copper and zinc concentrates as primary products and molybdenum and lead/bismuth/silver concentrates as by-products. In 2007, Metso Process Technology and Innovation (PTI) was contracted to increase SAG mill throughput by integrating and optimising blast fragmentation, crushing and grinding for the harder M4/M4A (CuZn) ores. Following the implementation of recommendations provided by Metso PTI, the SAG mill throughput increased from 2750tph to reach an average of 3600tph for the remainder of 2007. Due to continued application of mine to mill integration and optimisation philosophy, by 2010, the concentrator consistently exceeded the target of 4400tph while processing harder CuZn ores.

Jan 1, 2012

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By Balmer Neilly

In these days of arrested prosperity, when patience is tried and the future but dimly outlined, Canada's gold mining industry stands out as a beacon light shedding its rays of hope and confidence and demonstrating that there is still one product unaffected by Customs barriers and eagerly sought by all the people of the world. Some other forms of industry have hesitated and side-stepped. Some have cried for help, and in spite of public assistance, generously extended, they are still unable to demonstrate definitely their ability to resume the onward march. But gold mining has never hesitated. As an industry, it has bad an unique experience. When prices are high and conditions are generally referred to as prosperous, this industry is adversely affected. The cost of production goes up; profits are diminished; public sympathy is lacking; and, thrown upon its own resources, the industry tightens up its belt and throws its whole energy into an effort to improve operating conditions, and offset high prices by increased efficiency. When, in due course, depression follows inflation and prices ebb, the gold miner, through necessity, finds himself physically and mentally prepared to meet the situation.

Jan 1, 1932

By D. R. Wright

"The modest thermal efficiency of the steam turbine cycle essentially determines the heat required and, therefore, the coal consumption and ash production of pulverized-coal-fired powerplants. This paper emphasizes how some properties of coal and its ash can crucially affect the operation of a steam generator and its flue gas cleaning equipment. A brief reference to some siting factors and economics reaffirms the all-pervasive influence of the properties of coal and ash and establishes the importance of a firm supply of cooling water. The economics of scale remains a compelling factor in selecting the size of units, despite disappointing performances by some of the larger units. Environmental considerations suggest that smaller units still have a role to play. IntroductionCoal fuelled one industrial and economic revolution, beginning two hundred year s ago . It was the precursor of competing fuels, notably natural gas, oil and uranium, which eclipsed it in terms of convenience and rate of growth.The turmoil that now exists because of rapidly dwindling supplies of no-longer-cheap oil and the concerns about nuclear energy-justified or unjustified-exacerbated by an operating incident at the Three Mile Island Nuclear Powerplant, prompt speculation for a resurgence of coal, especially where it cangenerate electricity to replace energy from imported oil.The world's reserves of coal are not inexhaustible, although they are ample for several decades. Of greater import is the fact that the world's coal reserve s are more widely distributed than its oil reserves, and they appear less convenient as instruments of economic and political persuasion by opportunist powers. The crux is whether or not the world will accept all that a massive, if temporary, return to coal implies.Combustion of pulverized coal in steam generators to pro duce electricity is a 50-year-old, well-understood technique; it is undergoing continuous refinement to meet evolving environmental and economic criteria and is not found wanting. It is certainly the only technique available and technologically advanced enough to replace oil immediately on a large scale. Although it may take a decade to bring a new coal-fired powerplant into service, this delay is a reflection on nontechnical and administrative processes. Capital and operating costs of coal-fired powerplants are significant and subject to inflation, but, because of the accumulated experience in this field, the ability to control costs is better than for those energy processes which are less mature or still in embryo form. More exotic, soft energy systems, touted as the panacea for world energy problems, have still to prove themselves on the scale they are needed and under the stringent climatic and operating conditions coal-fired powerplants have already mastered."

Jan 1, 1980

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By I. Demers

The abandoned Manitou mine site covers an area of approximately 190 ha near Val d?Or, Quebec. This old site has been generating acid mine drainage for several decades. In 2006, a partnership was established between the Quebec Ministry of Ressources Naturelles (MRN) and Agnico-Eagle Mines to reclaim the Manitou site using tailings from the nearby Goldex mine. These neutral tailings were to be deposited on top of the Manitou site. An extensive study was performed to evaluate specific reclamation scenarios to control acid mine drainage using Goldex tailings as cover material. The article first describes the global approach used for this evaluation, which includes in-situ hydrogeological monitoring, tailings characterization, laboratory column tests, and numerical modelling. Of the thirteen column tests, three were conducted to evaluate the parameters affecting the performance of covers made of Goldex tailings placed over the spillage area of the Manitou site. Geochemical and hydrogeological parameters were assessed during the leaching column tests for almost two years. The tests aimed at evaluating the effect of water table level and monolayer cover thickness on the overall performance. The testing procedure involved monthly leaching and measurement of geochemical parameters. Results indicate that water table position is the most important factor affecting the monolayer cover performance to control AMD. Based on these results, it was established that the water table must be located near the interface between the Goldex and Manitou tailings to effectively reduce AMD generation. Cover thickness also has an impact on cover performance, which is however less significant than the water table position. The testing scenario with a water table located at the interface with a one-meter Goldex tailings cover showed progressive improvement in effluent quality.

Aug 1, 2013

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By CIM CIM

Why Workplace Important! ?We need Diversity is to do more in the industry as a whole to encourage and support diversity. It has long been an industry of white dudes and we?re not going to survive if that?s how we continue to think.? ? Mark Scott, HR Superintendent, Vale Inco PURPOSE OF MINING FOR DIVERSITY ? Share best practices in the areas of HR Development ? Support industry in attracting, recruiting and retaining a diverse workforce ? Raise awareness of industry HR challenges and collaborate with stakeholders to develop sustainable HR practices

May 1, 2009

By M. E. Sirkka

"INTRODUCTIONInco Ltd. has ten operating mines in the Sudbury district. Over the last ten years mining methods have changed at Inco with special emphasis on the introduction of bulk mining replacing conventional mechanized cut-and-f ill and undercut-and-fill methods. At the same time, the technology and size of LH D equipment has also progressed to meet the demands of bulk mining. This paper will concentrate on various aspects of the introduction and operation of electric LHD equipment a t Inco Limited, Ontario Division. BackgroundInco Limited received its first electric 2 cu. yd capacity LHD in July 1975 at Creighton Mine. The unit was tested pulling shrinkage stope muck and then was moved to a mechanized cut and- fill complex on 6600 Level. The electric scooptram received quick acceptance from the operators, due to its quiet operation and low heat generation, in a relatively hot operating environment. Although there are only two of these units operating a t present, this initial favourable experience, both in cost and efficiency, led to the development and purchase of electric scooptrams of the 5 cu. yd size. There are currently eleven 5 cu . yd electric LHDs in operation.The most recent development a t Inco is the move to yet larger electric LHDs in the 8 cu. yd size. The first electric ""Eight"" has now been in operation at Copper Cliff South Mine for over a year. This unit has the distinction of being the first one of its kind in service in North America. At the time of writing, there were ten 8 cu. yd electric ma chines operating in Inco's Ontario Division Mines, with three on order."

Jan 1, 1989

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

In gravity processing of gold-containing ore the target produced concentrate which is high gold grade primary concentrate contains a significant amount of cassiterite (SnO2). The plant attempts aiming at concentrate processing using a standard pyrometallurgical technology did not provide any positive results. The present paper is dedicated to development and testing of improved technology for pyrometallurgical processing of rich gold primary concentrate with high cassiterite content. According to material composition study primary concentrates produced at the plant contained 1.5–2.0% Au, 0.1–0.3% Ag, 55–65% SnO2, 20–25% Fe2O3, and 10–15% Fe3O4. The developed technology included alkaline nodulizing of primary concentrate mixed with sodium hydroxide and carbonate at 350–650°? with cake production. In blend nodulizing stannum and iron passed into sodium stannate (Na2SnO3) and sodium ferrate (NaFeO2) respectively. The blend of cake and fluxing agents was smelted at 1,150–1,200°? resulting in dore gold and slag production. Sodium stannate with 360°? melting point is well dissolved in slag system Na2OSiO2- B2O3-CaO. During plant tests 18.5 kg of high gold grade primary concentrate were processed, 1350 g of dore gold and 75 kg of slag were produced. Dore gold contained 16.5% Au, 0.95% Ag, 78.0% Sn, 3.1% Fe. Slag contained 12.4 g/t Au, 6.7 g/t Ag, 9.8% Sn, and 5.6% Fe. Gold recovery to target alloy was equal to 99.58 %, 87.8% of Sn passed into slag. This new technology was accepted for application at the plant.

Jan 1, 2016

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By M. Yavuz

As a branch of Operations Research, decision making is a widely used application in both science and social sciences. There are many different methods developed to solve decision making problems in the literature. In this study, Fuzzy Analytic Hierarchy Process (AHP) method is performed for the selection of reclamation project selection in an open pit mine and the optimal solution of the problem is investigated. Different reclamation project alternatives are prepared for an open pit mine, which continues to its production activities in magnesite sector in Turkey. The data obtained from Magnesite Cooperation is used in the application of the method. A decision-making process is prepared as considering the project alternatives for the purpose of selecting the most suitable reclamation project. The entire criteria that affect the decision-making process are identified and transformed into a hierarchical structure. The problem is solved by using Fuzzy AHP method developed according to this structure. It is found that Fuzzy AHP is a method that may help decision-makers in solving different decision-making problems in mining.

Aug 1, 2013

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013