Search Documents

By Michel G. Grenier

Compliance with Diesel Particulate Matter (DPM) exposure regulation is currently performed using timeweighted average (TWA) sampling on underground mine workers. These samples are collected in the span of an entire shift and the resulting concentrations are compared to a legislated exposure limit. While this is very useful to determine the exposure level of an individual to DPM, it fails to clearly identify causes of exposure and highlight opportunities that could help reduce the exposure of workers in the course of the work shift. Real-time DPM monitoring measures the worker?s exposure as a function of time and helps identify circumstances where corrective actions can be taken or design changes can be made by the individual or the employer to reduce the overall exposure of the worker and peers. This work focused on obtaining DPM concentrations using a real-time polycyclic aromatic hydrocarbon (PAH) monitor. The aim was to demonstrate that this instrument, while not a direct DPM analyzer, was able to provide a concentration profile that could easily be linearly correlated to standard TWA elemental carbon measurements. In addition, several instances of improvements that could be implemented to reduce the exposure of underground employees were demonstrated.

May 1, 2010

By Lawrence Melis

Fission Uranium Corp.’s Triple R Uranium Deposit at its Patterson Lake South Project is located in northwest Saskatchewan in Canada’s Athabasca Basin. As part of pre-feasibility studies for the project a detailed metallurgical test program was completed to provide process design criteria. The testwork program encompassed preparation and analysis of test composites, comminution testing, uranium acid leaching, liquid-solid separation, solvent extraction of uranium, precipitation of uranium yellowcake products, tailings and effluent treatment, tailings physical and chemical characterization, and environmental testing of prepared tailings, as well as investigations of gold and silver recovery from the mineralization. The paper provides mineralogical information, testwork methodologies and test results which were used to arrive at process design criteria and the selection of the process flowsheet for the project.

Jan 1, 2020

By M. E. Sirkka

"INTRODUCTIONInco Ltd. has ten operating mines in the Sudbury district. Over the last ten years mining methods have changed at Inco with special emphasis on the introduction of bulk mining replacing conventional mechanized cut-and-f ill and undercut-and-fill methods. At the same time, the technology and size of LH D equipment has also progressed to meet the demands of bulk mining. This paper will concentrate on various aspects of the introduction and operation of electric LHD equipment a t Inco Limited, Ontario Division. BackgroundInco Limited received its first electric 2 cu. yd capacity LHD in July 1975 at Creighton Mine. The unit was tested pulling shrinkage stope muck and then was moved to a mechanized cut and- fill complex on 6600 Level. The electric scooptram received quick acceptance from the operators, due to its quiet operation and low heat generation, in a relatively hot operating environment. Although there are only two of these units operating a t present, this initial favourable experience, both in cost and efficiency, led to the development and purchase of electric scooptrams of the 5 cu. yd size. There are currently eleven 5 cu . yd electric LHDs in operation.The most recent development a t Inco is the move to yet larger electric LHDs in the 8 cu. yd size. The first electric ""Eight"" has now been in operation at Copper Cliff South Mine for over a year. This unit has the distinction of being the first one of its kind in service in North America. At the time of writing, there were ten 8 cu. yd electric ma chines operating in Inco's Ontario Division Mines, with three on order."

Jan 1, 1989

By D. Ouellet, G. Gagnon, B. Simser, V. Falmagne

The mining sequence at Noranda’s Bell- Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the redimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Jan 1, 2004

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

"Many underground mines are achieving extended life and optimizing existing facilities by mining at greater depths. The challenges to do this require a sound engineering approach to mine design and mine services, as well as ingenuity in safety design. The social consequence is full utilization of existing infrastructure.Accessing ores at depths of 2000 m to 3000 m requires exceptional hoisting design. May’s theme issue includes a paper that examines a case study of one such hoisting plant, with emphasis on the hoist rope selection at Agnico-Eagle’s Penna shaft. The paper also describes the process whereby consultation with provincial safety authorities resulted in a revised safety factor suited to the hoist. Another paper examines the challenges of ventilating mechanized mines to 3000 m, including air cooling and dilution of diesel exhaust emissions. Vent system designs are discussed, using sound engineering design, and proven technology that minimizes emissions to achieve cost efficiencies. The paper suggests design based on process and ventilation simulators to obtain realistic economic data at the design stage. Increased ground pressures present unique challenges for production and safety. While this is not confined to deep mining, one paper examines rock pressures and seismic events at the Brunswick mine, for which experience may be applied at depth. It describes seismic monitoring as a predictive tool in a real mine situation, and how it is used to improve overall recoveries and maintain worker safety."

Jan 1, 2004

By H. Staton, V. Suontaka, E. Sharifi

"Flotation circuits are typically controlled using on-line elemental assays obtained from the slurry lines. In base metal applications, X-ray fluorescence (XRF) analyzers are the most common instruments for elemental analysis of the slurries. Eagle Mine has been utilizing a Courier XRF Analyzer since 2014. Typically, in XRF analysis, the sampling rate is 10-25 minutes which is good enough for manual process control. In 2018, Eagle Mine upgraded the Courier XRF analyzer with the Rapid Measurement module that is based on reflectance spectroscopy. This option reduces the sampling rate to 10-15 seconds, while maintaining the superior accuracy of the XRF analyzer. This paper presents the results from implementation of Rapid Measurement at Eagle Mine.INTRODUCTION Eagle mine is an underground mine producing nickel and copper concentrates. Eagle Mine is owned by Lundin mining and located in the Upper Peninsula of Michigan, USA. The Humboldt Mill, previously an iron ore processing facility, was refurbished in 2014 and is used to process the ore and produce separate nickel and copper concentrates. Approximately 2,000 metric tonnes of ore is milled per day. Ore is processed using a conventional crushing followed by single stage ball mill and flotation. Nickel and copper concentrate are transported to facilities in North America via rail car. A bulk copper-nickel concentrate is produced by separating the copper and nickel minerals from gangue material by flotation. The copper-nickel bulk concentrate is reground, followed by one stage of cleaning to reject further gangue minerals. The bulk cleaner concentrate is then subjected to a final flotation stage where the copper and nickel minerals are separated from one another through the addition of lime. Final concentrate grades are 14% Ni and 2% Cu in the nickel concentrate and 31% Cu and 0.8% Ni in copper concentrate."

Jan 1, 2019

By A. Bouajila

To stay competitive in an open market, mineral industries have to optimise their processes, lower their production costs and improve the commercial value of their products. Up to a recent past, they were impaired in this attempt by a lack of adequate devices allowing reliable on-line and real-time process monitoring (detection or measurement). Process monitoring for process control and the product characterisation for quality control are quite different tasks. Planners and researchers should be fully aware of this when evaluating or developing monitoring equipment for on-line process control. This paper will comment on some aspects of sensor specifications, during the design and the evaluation steps, related to sampling, measurement (accuracy, sensitivity, delay and correlation to the process) and suitability to the exploitation environment. Examples of R&D projects promoted by COREM for various industrial applications will be presented.

May 1, 2001

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By D. Van Tonder, C. Edwards

ABSTRACT Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium-bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares seven of these options on the basis of typical capital and operating costs for the solvent extraction circuit and downstream uranium processing and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.

Jan 1, 2013

By J. Zollinger, J. R. Kennedy, J. H. Park, D. Daloz

"In order to improve the properties of cast Ti-Al alloys to replace Ni-based superalloys past the low pressure stages of aircraft engines investigations into inoculation for grain refinement were carried out. Previous work showed isomorphic self-inoculation using Ti-Al-Nb particles was effective for grain refinement, however the relatively fast diffusion of Nb in Ti-Al make it difficult to observe the mechanism of nucleation. An alternative alloy was developed in the Ti-Ta system for isomorphic self-inoculation, maximizing the Ta content to improve the particles survivability in the melt. The powder processing produced comparatively small inoculant particles which dissolved, however larger particles were seen to survive solidification. The density difference between the inoculant particles and melt resulted in an inhomogeneous mixing of the particles and the melt with larger particles found near the outer edges of the ingots. Variations on particle size and interaction time between the inoculants and the melt resulted in the Ti-Ta inoculant reducing the as-cast equiaxed grain size by a factor of two compared to non-inoculated samples as well as increasing the equiaxed fraction in the ingot.INTRODUCTION Lightweight metals are of particular interest in aerospace applications. The hot sections of turbines are dominated by blades made of nickel based superalloys. Recently the GEnx turbine introduced TiAl blades in the last low pressure stage of the turbine to reduce weight and improve fuel efficiency (Kim & Dimiduk, 1991). In order to carry these benefits deeper into the turbine the high temperature (>800oC) properties of the alloys must be improved. Current grain refinement methods to improve properties rely on boron additions which may not be applicable for all blades as brittle precipitates may be formed during processing (McCullough, Levi, Mehrabian, & Hyman, 1991). A novel grain refinement process was previously introduced called “isomorphic self-inoculation” using Ti-Al-Nb particles to successfully grain refine TiAl (Kennedy, Zollinger, Bouzy, & Daloz, 2016). In order to better understand the mechanism of this process an investigation was carried out using the same process but with a Ti-Ta alloy which is more stable in the TiAl melt than the Ti-Al-Nb."

Jan 1, 2017

By C. R. Hocott

"IntroductionRESEARCH in petroleum production consists primarily in investigations related to the drilling for and recovery of oil. As an organized activity of individual oil companies, production research is now 30 to 35 years old, and the petroleum industry may point with justifiable pride to the achievements of this third of a •century. Emphasis on research has grown through the years until at the present time many of the larger companies operating in the United States •have well-organized production research staffs.In addition to the efforts of the oil companies, significant research and development in petroleum production technology have been performed by oilfield service companies and others. Valuable contributions have been made through fundamental research carried on by the U. S. Bureau of Mines and by various colleges and universities, both in their own programmes and in programmes sponsored by industry, such as those of the American Petroleum Institute. However, the total effort of these groups is small when compared to the sum of the effort devoted to research by the individual .oil companies. In contrast to some industries which conduct the major portion of their research through co-operative, sponsored research at universities or research institutions, research by the petroleum industry is done predominantly by individual company research staffs. These industrial research groups have usually been organized in such a way as to provide liaison and co-ordination with operating technical staffs. In this way, the research groups are kept aware of the major problems confronting the operating departments and, correspondingly, the operating technical people •are able to keep informed on research activity and progress. This type of close contact generally results in prompt testing of research developments in actual operations."

Jan 1, 1953

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By Roger Reed

It is well known that the performance and carbon emissions associated with the modern gas turbine engine depend critically upon the properties of the nickel-based superalloys, particularly those used in single crystal form. However, the design of all alloys in current use has been essentially empirical, or at best heavily reliant upon regression/neural network analysis of experimental datasets. In this paper, alloy design approaches [1] are described which are able to identify new alloy composition spaces which are worthy of experimental study. It is shown that a large amount of design data can be generated, which can be interpreted in different ways. Of course, the success of the approach depends heavily upon the accuracy of the underlying sub-models. Estimates of the creep resistance, cost, castability, density and oxidation resistance are made. It is demonstrated that these methods allow quantitative trade-offs to be made between the properties of interest.

Jan 1, 2010

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

In gravity processing of gold-containing ore the target produced concentrate which is high gold grade primary concentrate contains a significant amount of cassiterite (SnO2). The plant attempts aiming at concentrate processing using a standard pyrometallurgical technology did not provide any positive results. The present paper is dedicated to development and testing of improved technology for pyrometallurgical processing of rich gold primary concentrate with high cassiterite content. According to material composition study primary concentrates produced at the plant contained 1.5–2.0% Au, 0.1–0.3% Ag, 55–65% SnO2, 20–25% Fe2O3, and 10–15% Fe3O4. The developed technology included alkaline nodulizing of primary concentrate mixed with sodium hydroxide and carbonate at 350–650°? with cake production. In blend nodulizing stannum and iron passed into sodium stannate (Na2SnO3) and sodium ferrate (NaFeO2) respectively. The blend of cake and fluxing agents was smelted at 1,150–1,200°? resulting in dore gold and slag production. Sodium stannate with 360°? melting point is well dissolved in slag system Na2OSiO2- B2O3-CaO. During plant tests 18.5 kg of high gold grade primary concentrate were processed, 1350 g of dore gold and 75 kg of slag were produced. Dore gold contained 16.5% Au, 0.95% Ag, 78.0% Sn, 3.1% Fe. Slag contained 12.4 g/t Au, 6.7 g/t Ag, 9.8% Sn, and 5.6% Fe. Gold recovery to target alloy was equal to 99.58 %, 87.8% of Sn passed into slag. This new technology was accepted for application at the plant.

Jan 1, 2016