Search Documents

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By Charles Kingsley

THE PRESIDENT (DR. C. B. KINGSTON, member C.l.M.M.) expressed regret that neither of the authors of the paper was able to be present to submit the paper in person. In their absence, it would be introduced formally from the Chair. It was a clear, straightforward account of a fine piece of shaft sinking, cleverly conceived and boldly executed. He referred briefly to the distribution and nature of the Dome ore-bodies and stated that, for both the miner and the metallurgist, the mine had provided a wide range of problems of unusual interest. Discussion on the paper was then invited. MR. THOMAS PRYOR said the paper was most opportune, because the subject of internal shafts did not appear to be fully treated in current mining literature. Many members were not familiar with Canadian gold deposits and it would be of interest if the authors could give a brief description of the location of the ere deposits of the Dome mine. This information would doubtless explain why a new internal shaft was needed in a position which required such an exceptionally long cross-cut to connect it to the main hoisting shaft to surface. It would also add to the value of the paper if the authors would give some idea of the duty expected of the new shaft in terms of tons of rock hoisted and of trips engaged in the transport of men and materials, and it would be helpful if figures could be given of the total capital cost of the hoists and subsidiary excavations at the shaft top, and of the cost per foot for sinking and lining the shaft below the collar. Turning to details of the paper, one was favourably impressed by the care given to the provision of a good travelling way for men in the main cross-cut, as shown in Figure 1. It was by no means always that one could walk in comfort and safety in a working where there was a 20-in. ventilating pipe in the roof.

Jan 1, 1939

By J R. Barber, B. E. Rogers, R. Fukuzawa

Mercury is sometimes present in non-ferrous ores including gold, zinc, copper and lead. The selection and use of appropriate mercury abatement technology is critical for preventing its release to the environment during ore processing and to protect workers from mercury exposure. This paper presents a general decision-making process for mercury abatement technology selection for major emission sources in the gold industry. Mercury abatement can be accomplished through making process changes and/or by adding a process step to an existing system (i.e. "end-of-pipe control"). Advantages and limitations of the technologies along with waste / by-product management options are discussed through case studies of current operating mercury abatement systems.

Jan 1, 2015

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By John T. Whetton

"FROM 1850 when the annual production was around 50 million tons, coal output in Great Britain expanded rapidly to 225 million tons in 1900 and 287 million tons in 1913. However, during the First World War, countries which had previously bought large quantities of coal from Britain sought other sources of sup-ply or developed their own coal re-sources. Thus from the record figure of 73 million tons exported in 1913, Britain's coal exports declined until in 1938 they stood at 39 mil-lion tons. An important reason for this was the development of oil engines for marine propulsion. Today, nearly all the navies and mercantile shipping in the world have turned to oil engines. Sometime in the future, however, it is reasonable to expect nuclear power to replace oil.During the Second World War, coal output in Great Britain and manpower at the mines were reduced considerably and in 1.945, 175 mil-lion tons were produced by 709,000 miners. Exports were meagre, only 8.""7 million tons went to foreign consumption. During the severe winter of 1947, inland demand for coal exceeded production and exports were prohibited. Even importation of coal was required to meet inland demand. These were years when the coal industry of Great Britain made immense efforts to secure maximum output irrespective of economy. The energy needs of Great Britain appeared insatiable; but had it been possible to export, the nationalised mining industry could have made huge profits as there was a world shortage of coal. However, home needs were considered to be the priority and many overseas markets were lost. Other producers moved in and secured long-term contracts. Not only was the British export market lost, but also the nationalised industry had to sell the imported coal at the same prices as home-produced coal and suffered losses up to of:3 per ton. Bence, at a time when the National Coal Board might have ac-cumulated a reserve fund to cope with less prosperons times, it was having to spend large sums of money securing sufficient coal for inland consumption. This was a time when intensive efforts in the mining industry, comparable with those of many industries and establishments inclusive of the armed services during the war, would have produced a greater amount of coal and have been of immense value to the country as a whole."

Jan 1, 1960

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By B. Burger, T. Bester, S. Deonarain, L. S. Schultz

"This paper details the process followed to raise drill and equip a 6.1 metre diameter vertical service shaft at Glencore’s Mindola Deeps project in Kitwe, Copperbelt Province, Zambia. The project scope comprises a shaft collar, bulk air intake, a pre-sink to -90 metres and raise drilling the shaft from surface to a final depth of 1,892 metres underground, in four separate lifts of approximately 475 metres each. Equipping of the shaft steelwork, headframe erection and commissioning the shaft for hoisting. In addition, the scope included the development of a decline down from 5430’ level underground to the new shaft position on 6205’ level. This paper will provide some insight into the successes and challenges encountered during execution of the shaft works to date and provide some learnings for future projects of a similar nature. INTRODUCTION The Mindola Mine is situated to the west of the city of Kitwe in the Copperbelt Province of the Republic of Zambia (Figure 1). The mine is owned and operated by Mopani Copper Mines Plc (MCM), whose shareholders are Glencore AG (73.1%), First Quantum (17.9%) and ZCCM Holdings Plc (10%).Productivity at the Mindola mine has been adversely affected because of significant ventilation and ore re-handling challenges, which are caused by the dilapidated infrastructure, and design of the existing vertical and sub vertical shaft system. In the circumstances, it was apparent that it was necessary to sink a new vertical shaft that would increase the volume of fresh air down the mine, improving the underground working environment and the current hoisting restrictions, resulting in an increase in productivity and efficiency. Because there were two existing levels ideally situated and perpendicular to one another and because a third level was in close proximity to that perpendicular and because the mine required a ramp down to shaft bottom in any event, consideration was given to raise drilling the shaft as opposed to using conventional blind sinking methodologies."

Jan 1, 2019

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By J. C. Hawkins

Determining moisture content and rate of flow of a solid product make measurement and control of dryers unusually difficult. This paper de-scribes a method of accomplishing this with readily made air-temperature measurements. The system can cope with changes in feed moisture and feed rate. It does not measure solids temperature. The system's application to several typical rotary dryers is described, and control schemes using feedforward techniques are explained.

Jan 1, 1971

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By R. F. Favreau, L. C. Lang

"In modern blasting technology blasts are designed and analysed on an energy-mass-time relationship. The energy of the explosive is derived by computer analysis and the work potential of the available energy is expressed in numerical values. The mass involved in the blast is determined by the geometry of the blast and by the rock density. Time is also a relevant parameter, because time is required to complete the three basic stages of the breakage process.For successful application of the blasting parameters the basic mechanism of the breakage process must be understood.The physical-mechanical properties of the rock, local structural geology and the thermodynamic properties of the explosives can be brought together to create a computer model of a blast with which it is possible to predict separately the results of each parameter and to express the predicted degree of change in any parameter by actual numbers.A long-range project has started to create a ""bank"" of rock properties for as many Canadian and foreign mines as possible. A computer model has been successfully applied to predicting the effect of varying the ratio of spacing to burden at constant rock volume and significantly improved results are achieved, as the S/B ratio is increased up to about 2 to 2.5.High-speed photography has been applied to determine the time that has elapsed between zero time and the beginning of movement of the mass. The results assist in determining minimum and optimum delay time required for multiple-row blasting.The approach as described in the paper is now well proven and is clearly superior to previous methods based on powder factors and human assessment."

Jan 1, 1972

By Smortchevskyk N. J.

THIS paper describes the electrical features of the locomotive now (August, 1962) under construction for Craigmont Mines. Intended for non-specialists, it avoids details of design and calculations interesting to electricians only. The paper is divided into three sections. The first deals very briefly with the mine layout and with operating conditions -existing and expected. Reference is made to economic considerations leading to the selection of the type and size of locomotive, as well as to traction diagrams and the calculations. This material is not included in the paper because of its length and because it does not represent anything new. The second section deals with engineering and economic considerations and shows, in some detail, why the A.C. system was chosen. The third section describes the basic components of the locomotive, including the voltage regulator, the rectifiers, the control arrangement and the filter, and deals with considerations affecting the selection of their rating and design. A concluding sub-section describes, very briefly, the track and trolley details and the power distribution switchgear.

Jan 1, 1963

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By A. McEachern

At the Annual Meeting of this society, held in Halifax last year, a paper entitled "Closed System Breathing Apparatus" was read by I. C. Mackie, metallurgist, British Empire Steel Corporation. Coming from such an authority it was most instructive and illuminating. The purpose of the paper was to emphasize the necessity of a full supply of oxygen and the danger of oxygen shortage in the use of rescue breathing apparatus. In connection with this he pointed out: "In times of emergency, when life is at stake, rescue men cannot be restrained from using their utmost endeavor, and unless the apparatus is adequate to meet the heaviest load, the result may be fatal to the wearer. The body's demand for its oxygen requirement is absolutely imperative and must be granted at once. We can do without food for many days and without water for many hours, but we cannot do without full requirements of oxygen even for a few minutes. Furthermore, the victim of oxygen shortage gets practically no warning. He may fall helpless or unconscious before realizing that he is in a serious condition." Hence the necessity for expelling all the nitrogen from the breathing-bag and filling it with pure oxygen; also filling the lungs of the wearer with oxygen before he begins to use the breathing apparatus. This practice is general at all the collieries under the British Empire Steel Corporation.

Jan 1, 1924

By Fabio Mielli

In these times of increasing costs and diminished returns, energy consumption is one source of savings that remains relatively untapped in the mining sector. Typically, 15% to 40% of operational costs can be attributed to energy in mining operations. This ?process variable? is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. A mining company able to successfully embrace an energy efficiency program is more often than not a successful mining company. Production optimization programs, relatively common today, provide increased production, increased availability of assets and, in many cases, improved quality. They generally ignore the energy question altogether. Production Energy Optimization combines reductions in energy consumption with production improvements to reduce the cost per unit of production while improving emissions reporting. An energy strategy in mining and mineral processing operations is a critical component of Production Energy Optimization. This strategy must support the financial and operational integrity of the business. Developing a successful energy strategy requires a well structured approach such as following: ??Understanding where energy is being used and why, ??Recommending and implementing energy conservation measures, ??Driving visibility to targets and results, ??Re-evaluating continuously. The objective of this paper is to help you better understand the process, tools and technologies that enable mining organizations today to address energy and sustainability issues more tactically and proactively.

Aug 1, 2013