Search Documents

By Marcel Vallée

Abstract -Traditionally, samples collected for mineral deposit evaluation have been viewed without explicit reference to reliability, with the illusion that a true value is attainable from a few samples and verifications. For exploration, mineral deposit estimation and production quality control the following definition is proposed: "a sample is a small quantity of material relative to the geological mass it represents, collected according to a systematic procedure, of measurable reliability, from which the grade/quality of the mass which it represents may be estimated, based upon appropriate protocols. This paper will concentrate on the actual rock sampling process. Too often, sample size has been, and is still viewed as a matter of convenience, leaving out representivity considerations, despite the importance of samples on project estimation. Linear samples (chips, channels, drill), panel samples, broken rock or mining samples and very large samples are considered. Collection procedures and quality control protocols to improve the representivity of non-mechanical samples are proposed.

Jan 1, 1998

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949

The topic of the relationships between energy and particle size has had two very active periods -the first in the early thirties, when the relative merits of Rittinger's and Kick's proposals were vigorously debated; the second in the early fifties, when Bond's Third Theory was published. This second stage has produced several contributions that have provided a clearer picture of energy /size correlations in comminution. Derivations of a general relationship have been made from single-fracture experiments and from the rate of comminution, and both methods arrive at an equation of the type E = AK-11? The constant A in the equation may be regarded as a grindability parameter. In some respects, an understanding of the phenomena associated with comminution is still lacking, and research in this field should therefore be expanded. T HE SEARCH for a relationship between the energy consumed in comminution and the size of the broken product has been long and varied, and many

Jan 1, 1964

By M. Barati, K. Ebrahimi-Nasrabadi, P. W. Scott

"The conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally at temperatures of 400–1,200°C and for calcination times of up to 8 h. A differential thermal analysis– thermal gravimetric analysis showed that decomposition begins at temperatures as low as 340°C and is completed at 600°C. Specific surface area, iodine adsorption number, crystallite size, and loss on ignition were measured to characterize the product quality. It was found that high-quality caustic calcined magnesia can be produced in a narrow temperature (600–650°C) and time range (1–4 h).RÉSUMÉ La conversion de magnésite cryptocristalline en magnésie caustique a été étudiée de manière expérimentale à des températures de 400 à 1200 °C et pour des temps de calcination atteignant 8 heures. Une analyse thermique différentielle – analyse thermique gravimétrique montre que la décomposition commence à des températures aussi basses que 340 °C et qu’elle est complète à 600 °C. La surface spécifique, l’indice d’adsorption de l’iode, la taille des cristaux et la perte au feu ont été mesurés afin de caractériser la qualité du produit. Il a été trouvé qu’une magnésie caustique calcinée de grande qualité peut être produite dans un petit écart de température (600 à 650 °C) et dans une période de temps variant entre 1 et 4 heures."

Jan 1, 2015

By N. A. Beier, R. Amos, Smith. L., C. Atherton, D. R. Barsi, D. Blowes, D. C. Sego

"Waste rock is one of the most abundant materials at mine sites and must be properly characterized and managed to limit acid rock drainage and other harmful byproducts. An experimental waste rock pile—part of the test piles research program—located at the Diavik diamond mine (Northwest Territories, Canada) was deconstructed and sampled to study the spatial variability of material properties. Bulk samples were classified based on the amount of material finer than 4.75 mm. Hydraulic properties of each sample were estimated and particle size distribution analysis was completed. These datasets and classification methods might be used to improve the understanding of hydraulic and geochemical behaviour of the material and to study waste rock at other sites. ¦ KEYWORDS Acid rock drainage (ARD), Material classification, Particle size distribution (PSD), Waste rock RÉSUMÉ Les stériles font partie des matériaux les plus abondants sur les sites miniers et, en tant que tels, doivent être correctement caractérisés et gérés afin de limiter le drainage rocheux acide (DRA) et la pré¬sence d’autres sous-produits nocifs. Dans le cadre du programme Test Piles Research Program, un amas de roches stériles expérimental situé à la mine de diamant Diavik (Territoires du Nord-Ouest, Canada) a été décomposé et mis à l’essai afin d’étudier la variabilité spatiale des propriétés des matériaux. Les échan¬tillons en vrac ont été classés en fonction de la quantité de matériaux plus fins que 4,75 mm. Les propriétés hydrauliques de chaque échantillon ont été estimées et l’analyse de la composition granulométrique effectuée. Ces ensembles de données et méthodes de classement serviront à mieux comprendre le com¬portement hydraulique et géochimique du matériau et à étudier les stériles sur d’autres sites. ¦ MOTS CLÉS classement des matériaux, composition granulométrique, drainage rocheux acide (DRA), stérilesINTRODUCTION Statement of problem The characterization of mine waste rock remains a challenge in active mining sites. The large volume of material and the large size of particles make it difficult to collect representative samples. Sampling techniques are often dis-ruptive to mining operations because they alter the structure of the waste rock pile or interfere with mine traffic. The convention at most mine sites to collect little to no information on waste rock material means that models and predictions of how waste material will behave and interact with the surrounding environment are based on general information that might not be site specific. This could lead to environmental damage or higher costs if environmental effects are underestimated during the construction of waste rock structures."

Jan 1, 2019

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By C. Graham

Mechanisation has been a predominant theme of the past 50 years in the mining industry, particularly underground mining. As the level of technology employed has increased, the anticipated productivity gains have not been realised and the differences are not explained by the demand for higher standards of safety and security. Now, mining costs are so high and productivity so low that the resultant return on investment for many Canadian operations has fallen to levels considered unacceptable in a competitive capital market. Simply continuing technological development cannot reverse this trend and its financial implications. The focus on technological development has distracted us from some basic truths. Systems that are more complex are more likely to fail and cost-effective processes depend on the continuity of productive activity and the flow of material. When putting these facts together, it becomes clear that in a system that has fixed external conditions, the single most crucial issue is the effective management of the operational cycle. By its nature, technology focuses our attention on what gets done and how it gets done, while the crucial issue is the increasingly longer periods in the operational cycle when nothing productive is being done. What is required is to match the level of technological complexity to the fixed system conditions, which are virtually unchangeable. This paper looks at the overall system and objectives and attempts to present an appropriate level of technology for the Canadian mining industry, now and in the foreseeable future.

May 1, 2004

By C. Edwards

"The processes for rare earth (RE) extraction include the decomposition of RE ore concentrate minerals, and the concurrent or subsequent leaching of the rare earth elements (REEs) from the decomposed minerals. Ore beneficiation concentrate can be decomposed by, for example, acid roasting, caustic cracking, and chlorination. The REEs can be selectively extracted. The nature of the REE extraction process depends on the concentrate mineralogy and the targeted products. Based on the experience of the Saskatchewan Research Council (SRC) in RE processing, this paper reviews REE extraction from the major RE minerals, including bastnaesite, monazite, xenotime, ion-adsorption clay, allanite, cerite, and eudialyte. An update on the development of RE extraction processes is also provided.INTRODUCTIONRE processing usually involves two operation stages, physical processing and chemical processing. Physical processing, also known as ore beneficiation, separates the RE minerals from gangue minerals to produce an RE mineral concentrate. Chemical processing, which includes extraction and separation processes, converts the RE mineral concentrate to an RE compound which is either an end product or an intermediate product for the subsequent production of individual REEs or other compounds. The RE extraction process uses one or more reagents to decompose the RE minerals and to leach the REEs into solution. The RE separation process uses solvent extraction, ion-exchange, or chemical precipitation to produce either rare earth oxides (REOs) or individual REEs. The authors have previously reviewed RE ore beneficiation processes (Zhang & Edwards, 2012). This paper focuses on extraction processes for a variety of RE minerals. Table 1 gives the chemical compositions of the RE minerals mentioned in this paper. The varieties of RE extraction methods use many different reagents. These reagents are mainly inorganic acids, alkalis, salts, and chlorine gas. The commonly used acids include sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3). Sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) are the most common alkalis. Salts include ammonium sulphate ((NH4)2SO4), ammonium chloride (NH4Cl), and sodium chloride (NaCl). HCl is normally used to extract RE from silicate ore minerals such as allanite and gadolinite. The alkalis and H2SO4 are mainly used to leach REs from phosphate ores minerals like monazite and xenotime. The carbonate ore RE minerals such as bastnaesite can be treated using either acids or alkalis. HNO3 is mainly used to leach eudialyte and apatite. The extraction of REs from ionadsorption clay deposits uses salt solutions. Chlorine gas (Cl2) is exclusively used in the RE chlorination process which can be used to treat any RE minerals."

Jan 1, 2012

By Janne Karonen, Stephen Hughes, Mikael Jåfs, Jan Stål, Hannu Johto

End-of-life electrical and electronic scrap material attracts attention as a good opportunity for new value creation through efficient metal and energy recovery of such materials. On the other hand, the treatment of such wastes becomes important to avoid problems for society and environment. Treatment of such secondary raw materials faces multiple challenges due to their increasing complexity and evolving nature. Processing of these complex scrap materials together with recovery of a wide range of valuable metals with a combination of pyrometallurgy and hydrometallurgy using Outotec technology is discussed in this paper. One key consideration is environmental performance which needs attention when processing such complex secondary E-waste materials. Outotec has successful experience with commercial projects in the countries at the forefront of environmental and operational standards. INTRODUCTION Increasing attention has been drawn to the responsible processing of end of life Waste Electrical and Electronic Equipment (WEEE) as part of metals recycling, especially copper. It has been estimated that the amount of WEEE globally in 2016 was around the level of 46 Mtpa (Balde et al., 2017), representing a major disposal challenge but at the same time huge opportunity for resource recovery. The potential for increasing the recovery is high, because the official recycling rate of WEEE is in 2016 only 20% (Balde et al., 2017) and at the same time the estimated increase of the WEEE amount is between 3 and 5% per annum in the EU (Eurostat, 2019).

Jan 1, 2019

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By S. Power Warren

Introduction It is generally conceded by flotation men that the condition at the surface of a particle of mineral or gangue is the most important factor controlling its behaviour in a flotation cell. Much research work has been devoted to the study of the forces that are active at the surface of the particle and of the effect of the surrounding solution upon these forces. Study of the relationship between mineral or gangue particles and gas bubbles indicates that, in the main at least, flotation is a physical phenomenon. The important factor, that of mineral-gas-bubble attachment, is unquestionably physical; however, modifications may be effected by chemical means, whereby the nature either of the surface of the particle or of the surrounding solution may be changed. For example, the coating of lead sulphide that forms on lead-carbonate ore particles when sodium sulphide is added greatly aids the flotation of the carbonate particles. Without going into the question as to why, under certain surface conditions, mineral particles will attach themselves to gas bubbles whereas under other conditions they will remain unaffected, it may be stated that there are three general conditions in a flotation pulp which control the attachment of the particle and the gas bubble.

Jan 1, 1933

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973