Search Documents

By Bin Tang, Suping Yao

In the last decade, the copper industry in China has developed rapidly and attracted the world’s attention. The production capacity of refined copper has grown remarkably from 4.578 million tons in 2010 up to 9.029 million tons in 2018, accounting for about 40% of the global refined copper production. And now, China has become the biggest refined copper producer in the world. This paper summarizes the application of modern copper metallurgical technologies such as Outotec flash smelting/converting technology, Cyclone smelting technology, TSL (ISA/Ausmelt) smelting/converting technology, Jinfeng side blown smelting and Baiyin side blown smelting technology, Chifeng side blown smelting and continuous top blown converting technology, SKS bottom blowing technology, Dongying two-step smelting technology, copper electrorefining with high current density, etc. in China’s copper industry, analyzes and compares the characteristics of those technologies and presents the great efforts of China’s copper smelters in adapting to the increasingly strict emission standards and improving economic benefits of copper smelters. INTRODUCTION China has been the biggest refined copper producer in the world for many years. China produced million tons of refined copper in 2018, accounting for 40% of the copper smelting production in the world, and of which, roughly, 70% of the copper concentrate was imported, mainly from Chile, Peru and Australia. ICSG (International Copper Study Group, 2017) shows clearly the position of top 20 countries of copper production and copper mine production (Figures 1 and 2). Blast Furnaces, Reverb Furnaces and Electric Furnaces dominated China Copper Smelting for quite long time till 1980s. The first modern copper smelting technology (flash copper smelting) was introduced into China in 1980s, then followed by Noranda, Ausmelt and ISA. Since then, China copper smelting technology stepped into modern time. Since 2000, old processes (Blast Furnace, Reverb Furnaces and Electric Furnaces) were phased out and replaced by modern smelting technologies. China Copper Production has been increasing dramatically (Figure 3).

Jan 1, 2019

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

By R. Gallinger

In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale. The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP?s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP

May 1, 2005

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By Yufeng Yao, Robert P. Lowell

Abstract - Conductive heat flow anomalies associated with hydrothermal sulfide mounds on the seafloor have been studied. Sulfide mounds tend to focus conductive heat flow because sulfide minerals have a greater thermal conductivity than country rock. The topography of the mound above the seafloor, however, leads to a reduction of heat flow, particularly near the center of the mound. Because the focusing effect is constant, whereas the topographic effect decreases with distance away from the center, the focusing effect dominates toward the edges of the mound. The magnitude of these effects depends upon the conductivity contrast and the height/radius aspect ratio of the mound. Conductive heat flow anomalies at sulfide mounds also result from fluid circulation within the edifice. For the active and relict mounds at the TAG hydrothermal field, which have an aspect ratio of approximately 0.3 and a conductivity contrast of 3, the heat flux through the center of the mound should be roughly 70% of the background heat flux. The maximum effect of heat flow focusing is to increase the heat flux by about 30% above background. By comparing these effects with conductive heat flow data at TAG, we find that advective processes dominate conductive heat flow at both the active and relict mounds. Advective circulation can also give rise to much larger lateral and vertical temperature gradients than would result from conduction alone.

Jan 1, 1999

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By B. E. Jones

"The area of uranium deposition is situated within the Churchill Province on the western edge of the Wollaston Iithostructural domain where it underlies the eastern edge of the Helikian Athabasca Formation. The Collins Bay deposit is 6 miles north-northeast of the Rabbit Lake mine. Two principal zones of uranium mineralization are described.The ""A"" zone is a partly eroded, high-grade pod of metal oxide and arsenides sheathed by clay-like minerals. It trends north-northeast and lies under 25 to 40feet of water. Uranium mineralization is localized at or adjacent to the unconformity between the Athabasca Formation and the basement rocks. The basement comprises a granitoid Archean terrain overlain by paragneisses of the Aphebian Wollaston Group. ""A "" zone ore contains phyllosilicates, quartz, pitchblende, rammelsbergite, pararammelsbergite, carbonaceous material, galena, gersdorffite, niccolite, carbonate and a trace of sphalerite.The ""B "" zone lies 6,000 ft south of the ""A "", and subcrops under till cover. It is a partly eroded zone composed of metal oxide and arsenides which occur within variably altered Athabasca Formation. Minerals recognized are phyllosilicates, pitchblende, niccotite, gersdorffite, millerite, carbonaceous material, pyrrhotite, skutterudite and a trace of galena. The Athabasca Formation varies from 90 to 160ft thick. Granitoid gneisses of probable Archean age and paragneisses of the Wollaston Group underlie the deposit. An easterly dipping thrust fault transects its length.The deposit is typical of the ""unconformity-type"" uraniumnickel deposits of the Athabasca Basin. Observed features fit well with the ""diagenetic-hydrothermal"" model for such deposits, as envisioned by Hoeve and Sibbald (/978)."

Jan 1, 1980

By R. Gordon, J. Palich, W. Qian

The EarthProbe DCIP system deploys tightly spaced electrodes connected to a centralized data acquisition system that enables arbitrary selection of current and potential electrodes through relays. Rapid data collection (approximately 1000 readings per hour) and advanced signal processing allow for efficient use of conventional and novel arrays and the removal of natural and cultural noise. What is unique about the system is its electrode and borehole cable design, which allows seamless integration of borehole and surface measurements. EarthProbe operates in four configurations - surface, borehole, borehole-to-borehole, and surface-to-borehole (a variant of the borehole-to-borehole configuration).

Jan 1, 2011

By B. Lafrance, C. J. Beaumont-Smith, L. R. Jones

"Abstract - The Burnt Timber gold deposit is located in the Paleoproterozoic Lynn Lake greenstone belt of the Trans-Hudson Orogen, Manitoba. The deposit occurs along the Johnson shear zone, and is hosted by enriched and depleted tholeiitic volcanic arc basalts cut by feldspar porphyry dikes. The Johnson shear zone is a regional, belt-parallel structure characterized by the intensification of the regional S2 foliation. At the Burnt Timber deposit, S2 is folded by centimeter- to meter-scale, Z-shaped, F3 chevron folds that have an axial planar S3 crenulation cleavage. Within the 20 to 30 m-wide core zone of the shear zone, S2 and F3 are transposed parallel to S3 and the volcanic rocks are strongly sheared parallel to S3. The presence of a steeply plunging stretching lineation, together with dextral shear sense indicators along both S2 and S3 on horizontal surfaces, suggest that the Johnson shear zone is a dextral transpression zone. Gold was introduced in pyritic, biotitic, and carbonatized mafic volcanic rocks along the core of the shear zone. Mylonitic mafic volcanic rocks contain localized high-grade zones (=10 g/t Au) that differ from wider carbonatized, low-grade zones (<3 g/t Au) by the presence of deformed gold-bearing quartz-pyrite veins. High-grade zones are also associated with swarms of quartz-pyrite veins that cut across sericitized and carbonatized feldspar porphyry dikes, which acted as brittle, competent bodies during shearing. Gold deposition in the high-grade zones was controlled by the channeling of hydrothermal fluid along the core of the shear zone during shearing of the volcanic rocks, and brittle fracturing of the porphyry dikes. Sommaire - Le gîte aurifère de Burnt Timber est situé dans la ceinture de roches vertes Paléoprotérozoïque de Lynn Lake dans l’orogène Trans-Hudsonien, au Manitoba. Ce gîte est situé le long de la zone de cisaillement de Johnson et est encaissé dans des basaltes tholéiitiques d’arc enrichis et appauvris recoupés par des dykes porphyriques. La zone de cisaillement de Johnson est une structure régionale parallèle à la ceinture de Lynn Lake caractérisée par une intensité accrue de la foliation régionale S2. Au gîte de Burnt Timber, S2 est affectée par un plissement F3 en chevrons en Z d’échelle centimétrique à métrique associé à un clivage de crénulation de plan axial S3. Dans la zone centrale de 20 à 30 m de largeur au sein de la zone de cisaillement, S2 et F3 sont transposés parallèlement à S3 et les roches volcaniques sont fortement cisaillées le long de S3. La présence conjointe d’une linéation d’étirement à forte plongée et d’indicateurs cinématiques dextres sur les surfaces horizontales S2 et S3 suggère que la zone de cisaillement de Johnson est une zone transpressive dextre. L’or a été mis en place dans des volcanites mafiques altérées en pyrite, en biotite, et en carbonate au coeur de la zone de cisaillement. Les roches volcaniques mylonitiques présentent des zones aurifères locales à haute teneur (=10 g/t Au) qui diffèrent des zones à basse teneur (<3 g/t Au) par la présence de veines de quartz et de pyrite aurifère. Des zones à haute teneur associées à des essaims de veinules de quartz et de pyrite sont aussi notées dans des dykes porphyriques à plagioclase altérés en séricite et en carbonates; ces dykes se sont comportés comme des corps compétents durant le cisaillement. La déposition de l’or dans le zones à haute teneur a été contrôlée par la circulation du fluide hydrothermal au coeur de la zone de cisaillement durant la déformation des roches volcaniques et la fracturation des dykes porphyriques."

Jan 1, 2006

By M. R. P. Snow

"This paper outlines geotechnical conditions that commonly exist in underground, hardrock mines and the challenges posed for ground-support steel, specifically rockbolts, used in these environments. A model is proposed whereby the in-situ stress and rock-mass classifications (based on Bieniawski’s rock mass rating) form the basis of determining the desired steel properties of the rockbolts used. Based on the ASTM F432 bolting specification, recommended minimum steel properties are defined for three ranges of in-situ stress levels, each with their own six ranges of RMR values. Heat treatment for the steel can be specified once these minimum steel properties are known.RÉSUMÉ Le présent article décrit les conditions géotechniques qui existent fréquemment dans les mines souterraines de roches dures et les défis que cela pose pour le soutien de terrain en acier, plus spécifiquement les boulons d’ancrage utilisés dans ces environnements. Un modèle est proposé dans lequel les contraintes in situ et les classifications de la masse rocheuse (selon la classification de la masse rocheuse de Bieniawski) servent de base pour la détermination des propriétés désirées pour l’acier des boulons d’ancrage utilisés. En se basant sur les spécifications de boulonnage de l’ASTM F432, les propriétés minimales recommandées pour l’acier sont définies pour trois plages de niveaux de contraintes in situ, chacune avec sa propre plage de six valeurs de classification de la masse rocheuse (RMR). Un traitement thermique pour l’acier peut être spécifié une fois que ces propriétés minimales pour l’acier sont connues."

Jan 1, 2016

By B. Grinbaum, A. Mazuelos, F. Carranza, N. Iglesias, M. Avila, J. L. Lozano, G. Perez, R. Romero, M. \/aliente

Following a failure of a tailings pond darn at a mine in Andalusia, Spain, a huge effluent stream, that contained about 1 g/1 Zn and significant amounts of ferrous, ferric, calcium, copper, aluminium and manganese cations has to be treated, to prevent pollution of a nature reserve. EGMASA, as the regional government environmental agency, suggested to improve the current depuration process by recovery of the Zn from the effluent. A solvent extraction (SX) followed by electrowinning (EW) was proposed and developed to remove zinc.. A pre-treatment stage consisting in bio-oxidation of ferrous iron by using a bacterial process followed by an alkaline precipitation was employed because iron in the effluent is incompatible with both the SX and the EW processes. The SX process was developed successfully at the laboratory scale and verified in a pilot plant on-site, using two Bateman Pulsed Columns for extraction and stripping of zinc. The results were satisfactory obtaining a recovery of 90% of Zn. The process was suitable for industrial application.

Jan 1, 2008

By V. Nudo, R. del Villar, A. R. Laplante

"Fine iron ore recovery from the tails of Les Mines Quebec Cartier was investigated using Reichert trays and spirals. The effect of feed rate, density and splitter setting on the performance of rougher, cleaner and recleaner stages of a 2DS tray assembly was determined using 2- and 3- factorial experimental designs. The tray concentrate, assaying 27% Fe, was further upgraded by spiral to yield a concentrate assaying 55% Fe. Further laboratory scale testing showed this material to be easily upgraded to 65-66% Fe with high Fe recoveries.This paper presents the metallurgical results of the three tray stages. The model used to predict the performance of a full recovery circuit is then described. Simulation results are presented and their reliability assessed. Finally, an economic evaluation of the proposed scavenging circuit is summarized.INTRODUCTIONThe Mount Wright plant (UWP), located near Fermont, Quebec, processes daily 130,000-150,000 tonnes of iron ore assaying between 27 and 33% Fe, to upgrade it with three stages of 44.5 cm pitch GEC spirals to 66% Fe, while rejecting approximately 80,000 tonnes assaying between 6 and 11% Fe (1-3). Heavy liquid separation (at 3. 3 g/mL) of the plus 37 µm fraction (+400 mesh) of the tails reveals that a significant fraction of the iron is in the sink product, below 150 pm (100 mesh), as shown in Table 1. Also shown is the iron grade of the sink and float fractions. The high grade of the fine sink indicates that hematite ls well liberated below 105 µm (150 mesh), as previous studies have shown (4,5). The iron grade of the floats is very low in the fine size range, but increases with increasing size above 105 pm, because of incomplete liberation. Overall, two thirds of the plus 37 µm iron ls in the sink product, which constitutes less than 10% of the total tail."

Jan 1, 1987

By Paul Guliov

Coal-bearing Tertiary sediments of the Ravenscrag Formation in southern Saskatchewan host numerous deposits of clinker resulting from in situ coal combustion. Clinker deposits form when sediments of relatively low temperature firing properties overlie coal seams which are undergoing prolonged spontaneous combustion. The resulting fired material is useful for decorative landscaping aggregate, rock gardens, driveways, mud control and others. Predicting the occurrence of clinker deposits requires a knowledge of the spatial distribution of coal seams and the nature ofoverlying sediments. Knowledge ofpaleotopography at the time of coal combustion can assist in locating more highly-fused material which can yield greater block sizes. Coal data bases can be used as a predictive tool by outlining areas where coal is or was at or near surface and therefore may have been susceptible to spontaneous combustion.

Jan 1, 2001

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By Richard Phiri, Mike Milupi, Jackson Kapobe, Anton Lemmer, Charles Mazala

Sustainability of plant operations in a rapidly changing mining environment requires a well-trained workforce to ensure smooth running of operations. To ensure availability of trained labor, Mopani Copper Mines PLC set up a training facility in 2013. The school offers training in Engineering, Mining and Process. The engineering section enrolls grade 12 school leavers for artisan training. Mining section offers comprehensive safety induction program to employees and contractors to meet the Mopani zero tolerance accidents safety policy. The process training section offers advanced training programs for plant operating personnel and university graduates. The program includes needs analysis, theoretical metallurgical modules, practical plant training and e-learning modules. The school also offers assaying and sampling courses. All the above courses are extended to individuals and other mining houses outside Mopani wishing to have their personnel trained. The Mopani sustainable development academy ensures that contractors engaged on the Mopani sites are fully registered, comply with all relevant regulations and have undergone induction program before they can be allowed to work on the mine. INTRODUCTION “Sustainable operation of the mining industry requires a continuous supply of trained human resources” (Kapobe et al., 2018). The publication by the Asian Development Bank (2014) argued that there was a mismatch between the demand for high-level skills and the oversupply of low-level skills. Globally, the mining industry requires continued supply of skilled manpower for its complex operations and long term projects whose sustainability is absolutely necessary. Implementation of newer technologies in plant operations to ensure cost effective and efficient operations requires trained and skilled labor at various levels to handle ever-changing challenges. Dutz (2007:152–156) made three recommendations for Building Worker and Management Skills in India: Strengthen enterprise - based training. The government should help ensure that the benefits of in- service training are widely recognized by enterprises, while simultaneously providing strong financial incentives Improve vocational training - Vocational education and training systems have been unsuccessful in preparing graduates to meet market needs, particularly because of a lack of interaction with industry. Public and private vocational education and training providers should be strengthened to make them more responsive to industry demands. Curricula should be updated to reflect modern technologies. Strengthen business, management education, management of research and commercialization - business and management education should be strengthened through public-private partnerships. Innovative management courses should be introduced. Although these recommendations were made for India, they also apply to Zambia and other low and medium income nations.

Jan 1, 2019

By R. S. Bowman, G. S. Austin, J. M. Barker, P. S. Freeman

The physical, chemical and mineralogic characteristics of zeolites allow commercially important applications. While adoption of zeolite technology is slow in the United States compared to other regions of the world, continued testing and research has shown a wide range of uses for these minerals. They are important catalysts in petroleum refining, molecular sieves able to separate gases, and chemically inert carriers of reactants. The zeolite clinoptilolite produced by St. Cloud Mining Company (clino) (SC) is used in animal hygiene and animal feed, especially concentrated animal feeding operations (CAFOs), horticulture, water treatment, floor dry, aquariums, air and other filters, and odour control. Clino can remove cations from solution, and surface-modified zeolite (SMZ) is a sorbent for the removal of anions and neutral organics from water. Specific clino applications are: control of chemical pollution in groundwater, removal of organic compounds from oil field waters, and elimination of pathogens from sewage effluent. Combining the sorption capabilities of SMZ with chemical or biological transformations can yield complete removal of toxic materials from contaminated water. Continued development and marketing of zeolite products will be a growth market far into the future. The CAFO market for zeolites is the most significant growth area in the United States over the next few years. SMZ, currently less than 1% of St. Cloud sales, will continue to gain market penetration for many years.

Jan 1, 2004

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008