Search Documents

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By Anand Raman, Steve Dixon

"Industry practice for defining acid consumption is based on column tests. Freeport-McMoRan (FCX) has adopted a practice of leach operation using a defined pH or gpl acid in the raffinate based on the column test program. The acid consumption can be easily calculated using the leach operating parameters of SX-EW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate. The column leach test results and a column to heap efficiency factor are used to define the copper extraction. The maximum acid consumption will occur when zero acid is contained in the raffinate. The term Net Extracted Value (NEV) is to define the maximum extracted value relative to acid consumed.This paper presents the operating logic and method used to calculate acid consumption based on column tests and operating parameters.INTRODUCTIONIndustry practice for defining acid consumption is based on column tests. This may result in lower economic value if the tests are not designed to account for operating variables. A test program is described to assist in defining lift height and the influence of gangue on solution chemistry. A simple spreadsheet is presented that will use the leach operating parameters of SXEW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate to calculate the acid consumption for a proposed operation.A review of current leach operations solution chemistry will help to define acid consumption. This is recommended for all current leach operations.DISCUSSIONThe current practice at Freeport-McMoRan (FCX) is the use of column test results to define operating parameters. The monitoring of operational solution chemistry and copper production addresses any changes needed in operational parameters. This practice maximizes the value extracted from each tonne of ore leached."

Jan 1, 2008

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By J. E. Gebhardt

Advances in computational modeling provide unprecedented process simulation tools for the process engineer to examine and explore options for optimizing heap leach operations. A phenomenological model developed within a computational fluid dynamic software framework provides a general heap leach modeling tool that describes reactive dissolution and fluid flow through the stockpile. A one-dimensional form of the model is used to parameterize the kinetic leach reactions for a mixture of copper sulfide and oxide minerals against data from operational leach tests. A two dimensional version of the model provides a means to investigate the effects of irrigation rate, lift height, air injection, bacteria limitations, and other factors on recovery and pregnant leach solution concentrations. The model was calibrated for the Nifty Copper operation and ore type in order to simulate heap performance. Model simulations are reported for the chalcocitetype ore and compared to process data. The application showed that the multidimensional nature of heap leaching causes heterogeneous effects that are not always adequately described by one-dimensional models. Irrigation flow rate and aeration effects were simulated for a multi-lift heap section, and model results indicated that air injection at the base of the second lift would be required to achieve expected copper recovery under these lift height and flow conditions.

Jan 1, 2007

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004

By J. Starkey

A comminution circuit in recent history, is one of the most difficult parts of a mineral processing plant to design with confidence. It is usually the most costly part of a plant to build, and it can consume up to half or more of the energy used on a mine site. To suggest that comminution energy usage is sustainable in the long term is not possible at this time. What we have to choose from today, based on more than 50 years of experience, does include the best available technology, and the best way to design it. There is controversy in the industry as to how to properly approach the subject of comminution design, with many of the optional solutions requiring a level of training and expertise beyond the ability of a non-specialist engineer. Semi-autogenous grinding technology in particular, has not been properly appreciated because of many recent mistakes in its application and design, which have blurred the positive perception about what SAG technology is, how it can be used, and how it needs to be designed and built. In order to change this, mine owners and senior managers need to take responsibility for, and learn to understand the fundamental challenges that a comminution circuit poses to the project, to the design process, to the operators who use the equipment, and to the resulting metallurgy. This address is intended to summarize these challenges and offer fundamental engineering solutions, which are clear, specific and in a format which is directly applicable to the mining and mineral engineering community.

Jan 1, 2018

By A. D. Hunt

THIS PAPER will review Canada's fossil fuel situation as we understand it today and indicate some of the options available to meet our energy requirements during the next 15 years. It would therefore be helpful to examine Canada's total energy requirements and discuss the un certainties of the data base on which we must base future energy investment decisions. On the world scene, Canada is at the top of the energy-consuming nations, using about 49 bbls of oil equivalent per caput/ year. This appears to be slightly ahead of the U.S. and of course much higher than that of many countries. It is generally accepted that there is a more or less direct relationship between energy consumption and material standard of living. However , as we know, Canada, when compared with other industrialized countries on a GNP, an individual-income or some other standard basis, is lower in the list. This situation may be explained by our more severe climate and a relatively small population distributed over a land mass second only to that of the Soviet Union.

Jan 1, 1977

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By Neil H. Brown

Outline ? Cameco - Cigar Lake ? Cigar Lake Mine Development ? MDS #1 ? MDS #1 Improvements ? MDS #2 ? MDS #2 Improvements Pending ? Acknowledgements Mine Development System ? Mining methods tested and developed over the years ? Construction began officially in 2005 ? Water inflow events in 2006 and 2008 ? Successful dewatering and re-entry in 2010 ? Remediation continues ? Production target is mid-2013

Oct 1, 2010

By D. A. Jacobson

Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product. The MP1250?s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint.

Jan 1, 2012

By L. J. Visentin, J. G. Rickaby

"Audiometric testing is a key element in hearing conservation in the mining environment. This paper gives the history of the audiometric testing program carried out by Inco Metals Company, including the program objectives the personnel and equipment involved, calibration and testing, the test procedure, and the classification and evaluation of the test results.IntroductionThe operations of the Ontario Division of Inco Metals Company are located primarily in the Sudbury District. They also include a refine ry at Port Colborne and a mine and concentrator at Shebandowan near Thunder Bay.The company operates nine underground mines, and one open pit, while maintaining six underground mines on a standby basis. Ore from these operations is processed in four concentrators. The metallurgical facilities include a smelter, a matte processing plant, a copper refinery, a nickel refinery and an iron ore recovery plant at Sudbury, and a nickel refinery at Port Colborne. Inco Metals currently mines roughly 9,000,000 tons annually and produces IS elements.Excessive noise in the work place has been a serious problem in the mining industry since the introduction of compressed-air-powered machinery in the last century. At the same time, growing levels of noise inherent in our social environment can threaten the hearing of employees and their families.Only in the last 20 years, however, has the extent of this problem and its implications for people working in the industry and their families been recognized. Since the industry has become aware of the situation it has taken steps to implement comprehensive noise reduction and hearing conservation programs."

Jan 1, 1982

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By D. McConchie

BauxsolTM, prepared by treating bauxite refinery residues with Mg2+ and Ca2+, has an excellent ability to remove arsenic from acidic waters. The addition of BauxsolTM to sulphidic waste rock at the Gilt Edge Mine, South Dakota, reduced As concentrations in leachate water from 35 mg/L to < 0.005 mg/L; the concentrations have remained below 0.005 mg/L for the five years since the treatment was initiated. However, ordinary BauxsolTM does not effectively remove As from near-neutral water and it needs to be acid-treated or blended with small amounts of reagents, such as jarosite or ferrous sulphate, to increase the proportion of positively charged binding sites on the particles. The use of a jarosite/BauxsolTM blend can effectively treat ponded water, and As(V) concentrations can easily be reduced from over 1 mg/L to < 0.001 mg/L; As(III) has to be oxidised to As(V) for effective removal. Metal contaminants in the jarosite are trapped by the BauxsolTM and only very small amounts of the As, or other elements bound during treatment, are liberated using a TCLP leaching test. The exhausted treatment reagents meet the criteria for classification as an inert solid and do not need to be disposed of in a secure repository.

Jan 1, 2006

By Dale A. Sketchley

"Abstract - Large differences in gold content between rock fragments or small volumes of unbroken rock, commonly referred to as the nugget effect, are related to sample and subsample weights, crushing and pulverizing sizes, and density, shape and size distribution of gold grains. Gy’s sampling theory, which relates gold grain characteristics to sample weight, fragment size, and error, provides a method of estimating a sampling constant that quantifies deposit characteristics that contribute to the nugget effect.Sampling control tests provide methods for determining the sampling constant. Sampling control charts, comprising nomographs that relate sample weight, error and particle size, use the sampling constant to optimize sample weights and comminution sizes, and to minimize the variability introduced by incorrect or inadequate sampling and sub-sampling procedures. The sampling constant is useful in classifying ores into arbitrary categories according to expected sampling difficulties. Spatial variations in the sampling constant can be used to aid in defining ore types for modeling geological domains, which should have unique sampling protocols. Examples that illustrate the relationship between the sampling constant and expected sampling problems, and the spatial variation of the sampling constant, are given for various deposits. Case histories of sampling programs are presented.Quality control procedures consist of monitoring sample contamination amd accuracy and precision of analytical results. Accuracy, precision and contamination are monitored by including standards, duplicates and blanks into batches of samples being analyzed. Analytical results of standards and blanks are plotted on a batch-and-time basis with control lines at plus or minus two/three standard deviations as confidence limits of the accepted round-robin value. Examples are given that illustrate a laboratory system in statistical control and the various types of problems encountered when interpreting quality control data. These include sample transcription errors, degradation, contamination, sampling errors, detection limit problems, instrumental drift, lack of statistical control, laboratory bias, procedural problems and data tampering.Where bias is negligible, precision, as a function of concentration, can be obtained from duplicates using the Thompson-Howarth precision algorithm, which also allows calculation of the practical detection limit. Examples are given that illustrate variations in precision, with grain size, for different types of duplicates, as well as mineralogical changes and sampling errors."

Jan 1, 1998

By L. Long

Stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on siliceous goethitic (SG), goethitic (G), and saprolitic (SAP) nickel laterite samples (- 2000 ?m particle size) to evaluate the effect of stirrer speed, solid content, water salinity and grinding time. A fine mineral product (-38 µm) was used to evaluate the effect of selective grinding and Ni upgrade. The optimum grinding time for the highest Ni upgrade was 0.25 min, 0.1 min and 0.1 min for the SG, G, and SAP nickel laterite, respectively. A new feed (38-2000 µm) for each nickel laterite sample was prepared for batch grinding tests under the optimum grinding conditions. Upon grinding the 38-2000 µm feed, the - 38 µm product confirmed the effect of selective grinding and nickel upgrade. Size classification followed by stirred milling is a suggested process for Ni upgrade. The best Ni upgrade result was achieved on the SG nickel laterite among the three samples. The Ni grade increased from 0.85% to 1.37%, with 27.8% Ni recovery. Bottle roll leach tests showed that for SG and SAP samples selective grinding had no dramatic effect on Ni extraction due to the slow leach rate of hard mineral particles. Stirred milling of G sample increased the surface area of goethite, resulting in higher Ni extraction. Gravity concentration through a Knelson Concentrator was not effective in the further treatment of the stirred milling products either due to the poor operating conditions or due to the mineralogy characteristics of the feed samples. The energy requirement in the stirred milling was investigated. The first pass of the signature plots study is critical for the purpose of selective grinding, because the best result on selective grinding is achieved in the early stage of the grinding process.

Aug 1, 2013

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By P. O. Rag, Daniel E. Walsh

"Gravity concentrators are evaluated either in closed or open circuit. The process developed by MIRL employs the use of neutron activated gold (/98Au) and radiation detection circuits which monitor the concentrator&apos;s product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. In addition to allowing for a more accurate and detailed recovery analysis, this process significantly reduces the time and cost required for unit evaluation when compared to other gold recovery analysis procedures. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems.IntroductionThe surge in gold prices of the late 1970s and early 1980s was followed closely by a renewed interest in gravity concentration processes, especially in concentrators claiming efficient recovery of fine placer gold. Cones, spirals, spinning bowls, jigs and cyclones are all considered potential fine gold concentrators. Fine gold, in this context, is defined as not only that gold finer than 250 um (60 mesh""), but also coarser gold, whose low shape factor may decrease its recovery by conventional, large-scale sluicing operations.Adoption of fine gold concentrators by the Alaskan placer milling industry was retarded by the lack of reliable, accurate, and reproducible data on concentrator efficiency with respect to fine placer gold recovery. In most cases, concentrator performance was based on a limited number of tests run on placer material, about which only slight knowledge of gold size and shape characteristics existed. In order to be prepared for the resurgence of interest in fine gold concentrators, which will follow the next upturn in gold prices, a detailed study of the fine gold recovery characteristics of gravity concentrators needs to be conducted."

Jan 1, 1986

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

By G. Chi, A. Solomon, J. Lai

"The Buffalo gold deposit is a small deposit consisting of auriferous quartz-tourmaline veins within a granodiorite stock in the Red Lake greenstone belt. This study aims to characterize the mineralizing fluids through fluid inclusion and stable isotope analyses and to compare them with those of the world-class Campbell- Red Lake deposit. Four types of fluid inclusions were recognized, including carbonic, aqueous-carbonic, aqueous, and halite-bearing aqueous, with the carbonic type being the most abundant. Raman analyses indicate that the carbonic phase mainly consists of CO2, with minor amounts of N2 and CH4, and rarely detectable H2S. The homogenization temperatures of the carbonic inclusions range from -41.7° to 30.9°C. The homogenization temperatures and salinities of the aqueous, halite-bearing aqueous, and aqueous-carbonic inclusions are 130° to 276°C and 9.7 to 23.6 wt.% NaCl equiv., 155° to 207°C and 32.9 to 42.3 wt.% NaCl equiv., and 215° to 357°C and 8.3 to 19.7 wt.% NaCl equiv., respectively. The d18OVSMOW values of tourmaline range from 8.2‰ to 9.0‰, and those of quartz from 11.4‰ to 11.9‰, with estimated fluid temperatures from 323° to 399°C based on the quartz-tourmaline isotopic geothermometer. It is postulated that separate CO2-dominated and aqueous fluids intermittently invaded the fracture/vein system in response to fluid pressure fluctuations, with limited mixing. The CO2-dominated fluid, previously recognized in Campbell-Red Lake as the main mineralizing fluid, is inferred to have been derived from deeper parts of the crust. This deep CO2-dominated fluid reservoir might have been a common source for gold mineralization in the Red Lake greenstone belt. Le gîte aurifère Buffalo est un petit dépôt composée de veines de quartz-tourmaline à l’intérieur d’un stock de granodiorite dans la ceinture de roches vertes de Red Lake. Cette étude vise à caractériser les fluides impliqués dans la minéralisation par les inclusions fluides et par les isotopes stables ainsi que de les comparer avec ceux du gîte de classe mondiale de Campbell-Red Lake. Quatre types d’inclusions ont été notes, incluant des inclusions carboniques, aqueuses-carboniques, aqueuses et aqueuses avec halite, les inclusions carboniques étant la variété la plus abondante. Les analyses par spectroscopie Raman indiquent que la phase carbonique consiste principalement en CO2, avec des quantités mineures de N2 et de CH4, et rarement avec des quantités mesurables de H2S. Les températures d’homogénéisation des inclusions carboniques vont de -41.7° to 30.9°C. Les températures d’homogénéisation et les salinités des inclusions aqueuses, aqueuses avec halite et aqueuses-carboniques sont varient de 130° à 276°C et de 9.7 à 23.6 poids.% NaCl équiv., 155° à 207°C et 32.9 à 42.3 poids.% NaCl équiv., et de 215° à 357°C et 8.3 à 19.7 poids.% NaCl équiv., respectivement. Les valeurs de d18OVSMOW pour la tourmaline vont de 8.2 à 9.0‰, et celles du quartz de 11.4 à 11.9‰, avec une température estimée du fluide entre 323° et 399°C sur la base du géothermomètre isotopique quartz-tourmaline. Il est postulé qu’un fluide riche en CO2 et un fluide aqueux distinct ont envahi le système de fractures/veines par intermittence en réponse à des variations dans la pression des fluides, et qu’il y a eu peu de mélange. Le fluide riche en CO2 est également observé à Campbell-Red Lake ou il est le fluide minéralisant principal, il est présumé être dérivé de portions plus profondes de la croûte. Ce réservoir profond de fluides riches en CO2 pourrait être la source commune des minéralisations aurifères de la ceinture de roches vertes de Red Lake."

Jan 1, 2009