Search Documents

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By G. P. Demopoulos

The solubilities of calcium sulfate in HCl-CaC1z-H20 solutions up to 100°C were successfully modelled with the aid of OLI software after bringing proper modification to it. Modelling, more specifically, was carried out with the help of the Environmental Simulation Program, V-6.6.0.4 (www.olisystems.com). New model parameters were obtained by regressing the solubility data. A private databank was established by adding the newly defined model parameters and the calcium sulfate hemihydrate phase that is not included in the original OLI database. The McGill-modified OLI software was successfully applied not only to modelling solubilities but also the transformation of the various CaS04 phases, namely dihydrate, hemihydrate and anhydrite. In this paper, the modelling methodology will be discussed along with a comparison of the capabilities of the newly developed model vs the original OLI model.

Jan 1, 2005

By Michel Aubertin

Mining activities can produce large volumes of waste rock, which are typically deposited in piles on the soil surface, above the water table. Such piles can cover areas of several tens of hectares and can reach over a hundred meters in height. For hard rock mines, the waste rock grain size can vary from silty particles to metre-scale blocks. The internal structure of a pile constructed on a relatively flat surface typically includes two main zones. The first zone corresponds to the heart of the pile, and is formed by several sub-horizontal stratifications (with dense and loose layers) due to the heavy mine equipment traffic which induces local compaction and degradation of the waste rock. The second zone corresponds to regions where waste rocks are deposited by push-dumping or end-dumping close to the external flank of the pile, inducing grain size segregation along the slope. Depending on the deposition sequence, grain size distribution and bench height, a gradation may then be observed, with coarser particles (with cobbles and blocks) near the base and finer particles near the crest, together with inclined stratifications due to the advance of the deposition face. These internal features affect the distribution and flow of water (and air) in the pile. To assess the internal distribution of material properties within the pile, a combination of several tools is usually required which can provide information on the hydrogeological and geochemical characteristics of the waste rock. In this regard, geophysical tools are very interesting because they can lead to a threedimensional mapping of property variations. The information gathered from a combination of appropriately selected techniques can be used to construct numerical models to further study unsaturated water flow and reactive transport. Such simulations help better understand the pile response in its actual and future states, which in turn provides input to adjust the deposition sequence, to plan for closure, and to select an in situ groundwater monitoring strategy. The presentation will give an overview of techniques that have been developed to characterise material properties in the laboratory and in the field, and to obtain a general picture of a pile?s internal structure. Additional results on unsaturated reactive transport modelling will also be shown to illustrate how the internal pile structure may influence its hydro-geochemical and environmental response.

Nov 1, 2008

By H. M. Lizama, R. L. Stephens

Secondary leaching of previously leached supergene copper ore has been developed and implemented at Teck’s Quebrada Blanca operations. This consists of using in-situ leaching techniques aided by geophysics to recover the residual metal value from dormant copper leaching heaps. These heaps of crushed and agglomerated ore had been leached 20 years previously but still contained significant copper values. The concept was first tested on a 3,200 m² sector, where injection wells introduced leaching solution into a production zone and electro-resistivity tomography was used to track solution movement within. Operating parameters such as well spacing and injection flow rates were determined. Copper recovery and leaching performance were evaluated based on solution and metallurgical balances. Both ferric leaching and bacterial leaching were enhanced through strategies to pull air into the heap. Positive results from the initial test prompted a larger, industrial pilot test on a 60,000 m² area and 97 injection wells. This larger test obtained a copper recovery of 30% in 457 days. Secondary recovery is now being implemented to all of the abandoned heaps at Quebrada Blanca and has become a production stream. This technology has the potential of wide application to mature copper heap leach operations, and Teck has patented the process and associated methodologies. INTRODUCTION Heap leaching of copper secondary sulphides has been carried out at Quebrada Blanca (QB) since 1994. Ore from the supergene deposit was crushed and agglomerated prior to leaching. Originally, the ore was leached in 6 m lifts stacked one on top of another, known as a static pad configuration. However, in 1998, after the second lift, the operation changed to a dynamic pad configuration; the ore was leached in a single lift and the resulting residues were removed to make way for fresh ore (Yáñez, Ahlborn, & Ramos, 2007). The first two static lifts were left in place and served as a foundation for the dynamic lifts above. Those two buried lifts of leached residues, some 16.8 million tonnes and covering an area of approximately 0.71 million m², remained buried under the dynamic pad.

Jan 1, 2019

By E. Vesely, A. Saxena

"SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Because of the collisional environment directly measuring such dynamical loads is extremely difficult if not impossible. In this study we tried to evaluate the liner failure risk by simulating the collisions of solid particles with mill liner using Discrete Element Method (DEM). DEM simulation has been proved to be a very useful tool in evaluation of granular flow and its impacts on the solid structure. But there are certain limits in DEM coherently, such as the number of solid elements, the computer runtime, etc. Here we first present the general feature of the particle-liner collision in terms of impact force and collision energy. Then the effects of parameter selection is discussed. Our simulations show the fatal collisional event of huge impact force is very rare and the collisional events of low impact is much more frequent. The fatal event may contribute most to the liner failure. The rarity of the fatal events may be missed in a short runtime simulation. This technical challenge combined with lacking of criterion to evaluate varying impact loads in fatigue problems may further complicate the evaluation. Should we use the largest impact force alone or we should use the more frequent events is an open question and requires more effort. In order to evaluate the quality of liner design, we proposed a relative comparison method. In the end we show the implication and application of this method in liner optimization by a work example. In particular, the effects of the charge level of grinding balls and their size on the operation performance is presented.INTRODUCTION Grinding is one of the most important and expensive steps of mineral processing. A variety of grinding mills such as rod mills, ball mills, semi-autogenous (SAG) mills and autogenous (AG) mills are being utilized for comminution of mineral ores (Gupta & Yan, 2016). Up to today, SAG mills and AG mills have been widely used to reduce operation costs and increase throughput. In an AG mill, a rotating drum throws larger rocks of ore in a cascading motion which causes impact breakage of larger rocks and compressive grinding of finer particles. Unlike AG mills, SAG mills use steel grinding balls to break ores of size quite small such that they cannot be easily broken in AG mill. SAG mill liners are designed for protecting the mill shell and providing lifting power for ore charge and grinding media. Due to the impacts from the charge and the grinding media, the liner experiences dimple, plastic deformation, strain hardening, fatigue, peening and final failure. Quality and performance of SAG mill liners play a fundamental role to enhance efficiency of grinding mills, because failure of liners is the major cause for unexpected breakdown (Banisi, Hadizadeh, Mahmoudabadi, & Eilkhany, 2006)."

Jan 1, 2019

By Burden of Occupational Cancer in Canada Project Team, Demers P. A., Kim J., Arrandale V. H., Jardine K.

"In 2012 diesel engine exhaust (DEE) was classified as a human carcinogen by the International Agency for Research on Cancer (IARC) and is one of the most common workplace carcinogens internationally. We estimate that approximately 2.4% of lung cancers (n=560) and a suspected 2.7% of bladder cancers (n=200) are attributable to occupational exposure to DEE annually in Canada. High levels of exposure to DEE in mining results in a disproportionate number of cancers in this sector (approximately 220 lung and 20 suspected bladder cancers annually). These could be prevented by reducing the number of workers exposed and level of exposure. KEYWORDS Bladder cancer, Diesel engine exhaust, Economic burden, Lung cancer, Mining, Occupational cancer, Prevention, Regulation INTRODUCTION Diesel engine exhaust is a complex mixture of gases and particulates containing known and suspected carcinogens such as benzene, polycyclic aromatic hydrocarbons (PAHs), and metals. Approximately 900,000 Canadians are exposed to diesel engine exhaust at work, making it the most prevalent occupational lung carcinogen in Canada (CAREX Canada). Diesel engine exhaust is recognized as one of the most common workplace carcinogens in the world, but its classification as a human carcinogen by the International Agency for Research on Cancer (IARC) was relatively recent. In 2012, after decades of mounting evidence, diesel engine exhaust was upgraded from a probable (IARC Group 2A) to a definite human carcinogen (IARC Group 1) (IARC, 2014). The IARC evaluation was based on strong evidence in humans for an increased risk of lung cancer, as well as strong evidence in animal studies. The key human evidence considered by IARC was from epidemiologic studies of workers in truck transportation, rail transportation, and mining industries, where the use of diesel engines is widespread. These studies provided strong sufficient evidence for an increased risk of lung cancer, as well as limited evidence for bladder cancer. The human studies used particulate matter, generally measured as elemental carbon (EC) or total carbon, as a surrogate for diesel engine exhaust to assess the risk associated with level of exposure. The animal studies reviewed by IARC showed sufficient evidence for cancer with exposure to whole diesel exhaust and the particulate matter fraction of diesel exhaust, but not for the gas phase components."

Jan 1, 2019

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962

By P. Lefebvre, J. Sargent, K. Major, B. Darnton

"Stillwater Mining commenced mining operations at Nye, Montana in 1987 for the recovery of platinum and palladium. Exploration identified that the J-M Reef extended for 43 km. In 1998 Stillwater Mining made the decision to develop the East Boulder mine complex, located approximately 13 miles from the Stillwater mine complex at Nye, to increase production. This paper describes the design, construction, and start-up of the East Boulder process plant.INTRODUCTIONStillwater Mining Company have been producing Platinum and Palladium from their Nye, Montana operations since 1987. The mine production from Nye had been increased in stages with mine production being delivered through several portals and one vertical shaft.The deposit is narrow veined which prevents the application of bulk mining methods and thus limits the production capabilities.In order to increase the production of platinum (Pt) and palladium (Pd) Stillwater made the decision to access the ore from the J-M Reef from the East Boulder site. The East Boulder mine site is located about 21 km (13 miles) from Nye, however as shown in Figure 1, the travel distance is closer to 188 km (114 miles). Distance, on strike, and space availability at Nye precluded the expansion of the Nye concentrator to handle the increased mining rate and supported the decision to install a new concentrator at East Boulder."

Jan 1, 2003

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By M. Boher, J. Lehmann, M. C. Kaerlé

"In the production of high quality steel, the understanding of the interactions between liquid steel and refractories and of their effect on steel purity and cleanness are becoming more and more important.An experimental study has been per-formed in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel. The results show a pollution of the liquid steel:•the silicon content of the liquid steel increases due to the reduction of the silica of the refractory by the aluminum contained in the steel; and•a reoxidation of the steel occurs and the formation of an oxide layer on the refracto-ry, mainly composed of spinel crystals and of Ca-aluminates is observed.The transfer mechanisms of the various elements are analyzed."

Jan 1, 1997

By H. Matsuoka, M. Kawata, K. Mitsuhashi, C. Tokoro, T. Kato

Copper sulfide minerals such as chalcocite, bornite, and chalcopyrite exhibit high floatability, thus they can be recovered as a froth product by adding only a collector in flotation process. However, when their surface is oxidized, the floatability decreases and the simple addition of collectors is no longer effective. In this case, flotation activators are required to improve the floatability. Sodium hydrosulfide (NaHS) acts as an activator for chalcocite and bornite by re-sulfurizing their oxidized surface portions. Nevertheless, the flotation conditions still require optimization in order to achieve a satisfactory recovery of copper minerals. This work addresses the study of the effect of pH and NaHS dosage on the flotation of a complex Chilean copper ore containing chalcocite, bornite, and chalcopyrite. Flotation experiments were conducted using a Denver-type flotation cell and by investigating the effect of two NaHS dosages (50, 100 g/t) and three pH values (8, 9, 10). Following this process, the surface interaction between the minerals and NaHS were analyzed using zeta potential measurements. INTRODUCTION In recent years in the mining area of metal resources, the complexity of ores and the fineness of grind required to liberate minerals have become serious problems. When ores are complex, several valuable minerals may interact with each other and reactions may become more complicated compared with an ore containing only one valuable mineral. Therefore, more processing steps may be required than for a simple ore. When the valuable minerals exist as fine grains, it is difficult to liberate them and more grinding time is required. Furthermore, the probability of collision of fine particles with bubbles in the flotation process declines and it takes much time to recover them. Flotation is one of the most applied methods to separate valuable minerals from unwanted ones using the difference of hydrophobicity (or hydrophilicity). In the flotation method, the air is fed to a cell filled with the pulp of the mineral of interest and agitation is implemented to introduce air and generate bubbles. The hydrophobic particles attach themselves to the bubbles and float along with the bubbles while the hydrophilic particles remain in the pulp. Copper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are widely known abundant copper resources. Generally, flotation is used to recover and concentrate these minerals. Copper sulfide minerals usually have high floatability. However when their surfaces are oxidized, their floatability becomes lower. When the sulfide surfaces are oxidized, activators are added before flotation to modify the surface property of the Copper sulfide minerals so that they can be floated. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao (2018) reported that NaHS is often used as a sulfurizer for oxidized sulfide minerals (Becker (2014), Clark (2000), Newell (2006), and Newell (2007)). In earlier work, the authors performed flotation tests on a sample of Chilean copper ore which contained chalcocite, bornite, and chalcopyrite using a Denver-type flotation apparatus. The sample was ground to P80 70 µm with a rod mill and ball mill. In these tests, the following conditions were used: natural pH (about pH 8.5), flotation time of 45 min, 60 g/t AP3477 (sodium diisobutyl dithiophosphate) as collector, and MIBC (methyl isobutyl carbinol) at appropriate dosage as frother. NaHS was applied at the dosage of 0, 67, and 120 g/t, respectively at the conditioning. The concentrates were collected at 6, 18, 30, and 45 min. The weights of the concentrates and tailing were measured and they were assayed for copper by ICP-AES (Optima 5300 DV, PerkinElmer Inc.). The flotation recoveries of the copper minerals were calculated from the results of MLA (mineral liberation analyser) (MLA 650, FEI) measurements.

Jan 1, 2019

By G. W. Toop

"The Cominco smeller in Trail, British Columbia, is a large integrated lead-zinc production facility. In the plant description, emphasis is given to the pyrometallurgical operations including zinc concentrate roasting, lead singer-blast furnace processing and silver refining. Production figures for the main metal products - zinc, lead, silver and gold - are provided.IntroductionIncorporated in 1906, Cominco Ltd. is an integrated natural resource company with principal activities in mining, smelting and refining, mineral exploration, fertilizer production and electrical power generation.Cominco is one of the world's largest producers of zinc and lead, accoW1ting for about 10070 of mine production in the western world. The company also produces and sells copper concentrate, copper sulphate, copper arsenate, sodium antirnonate, silver, gold, cadmium, bismuth, indium, and germanium dioxide and a range of fertilizers and sulphur products.Zinc OperationsRoastingThe roasters currently treat about 1400 t/d of zinc concentrates. Over half of the total concentrate treated originates from the Red Dog Mine in Alaska. During the summer, concentrate is shipped from Alaska to Vancouver where it is loaded into rail cars and hauled inland, transferred to trucks and delivered to Trail. The remainder of the roaster feed is made up of Sullivan concentrate and various custom concentrates. These arrive either by train or by truck.There are three roasters available for roasting the concentrate. The two major roasters are Lurgi fluid bed units. Each Lurgi roaster can process concentrate at about 1:7 tonnes per hour (tlb). A smaller Cominco suspension roaster with a capacity of 10 tlb is also used. The flowsheet for the high temperature section of the fluid bed circuit is shown in Figure 1.Concentrates fed to fluid bed roasting are conditioned with 7 1/min water to give 8% moisture in feed. Two slinger belts throw the mixture into the fluidized bed. The fluid bed roasters are 10.4 m in diameter with a bed depth of 1 m. Grate area is 84 m2• Normal operating conditions include bed temperatures of 930°C to 950°C, fluidizing air at 750 Nm3/min and a wind box pressure of 2000 mm H2O."

Jan 1, 1994

By H. A. Wentworth

The Central Manitoba mining district, as spoken of in Manitoba, refers to that portion of the country lying between lake Winnipeg on the west and the Ontario boundary on the east, and from a few miles north of the Wanipigow (or Hole) river on the north, to a few miles south of the Bird river. It embraces two known mineralized belts; the gold area in the north, extending from the shores of lake Winnipeg almost to the Ontario boundary (in a slightly southeasterly direction) a zone some eight or ten miles wide and perhaps forty miles long, lying (for the most part) north, and parallel to, the Manigotagan river; and the Bird river copper and coppernickel deposits, an area not yet clearly defined, but in general lying immediately north of, and roughly parallel to, the Bird river. To the south of the Bird river is a somewhat differently mineralized area, numerous pegmatite dykes being found, with minerals typically associated with such rocks. More specifically, the known gold deposits are largely segregated in the above belt; (1) around English brook; (2) along the north shore of Wanipigow lake; the Rice lake area (about midway of the belt); and the Long Lake-Bulldog lake area, at the eastern end of the belt. Not all the known gold occurences are found in these segregations, but the density of claim staking in these areas is perhaps an indication of the greater number of prospects found in them to date.

Jan 1, 1925

By Hamid Butt

Information Technology ??Advanced Information Technology is dramatically changing information flow within organizations. This enables employees to have information at their fingertips to make informed and prompt decisions. ??Real-time information allows timely analysis, which dramatically reduces cycle times, making organizations faster and more flexible. Business Challenges ??Continual growth of mining and Mine mobile fleet.??Increasing maintenance costs. ??Difficult to identify and troubleshoot equipment problems while equipment is operating. ??New equipment is increasing in complexity and cost. Therefore, each failure results in a greater impact to production and cost. ??Troubleshooting practice is reactive. ??Protect and optimize the use of mining assets to realize maximum business value. ??Maintenance and Operating information is not easily accessible ?no near real-time system that provides complete information.

May 1, 2006

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By I. C. Brown, J. F. Henderson

"IntroductionThe Yellowknife greenstone belt lies along the west side of Yellowknife bay on the north shore of Great Slave lake, some 600 miles north of Edmonton, Alberta. The producing gold mines along the belt include the Con-Rycon and Negus which came into production in 1938 and 1939, and the Giant Yellowknife, which followed in 1948. In addition to these, the Akaitcho and Crestaurum mines are potential producers and there are several promising prospects.Early geological work along the belt was done by A. W. Jolliffe who first recognized a number of great faults, the largest of which is the West Bay fault with a horizontal movement of more than 3 miles. In 1943, A. S. Dadson, following an examination of the Giant-Yellowknife property, advanced the hypothesis that Baker Creek valley was underlain by a series of major gold-bearing shear zones. Subsequent diamond drilling in 1944 bore out the correctness of this view and outlined the great ore-bearing shear zones that are now being developed and mined by Giant Yellowknife Gold Mines. Near the south boundary of the Giant property, the shear zones are cut off by the West Bay fault. This prompted Neil Campbell, District Geologist for the Consolidated Mining and Smelting Company, to make a detailed study of the geology along the West Bay fault in the hope of finding the faulted extension of the Giant shear-zone system on the west side of this fault. In this he was entirely successful. By careful geological mapping he matched several faulted diabase dykes on both sides of the fault and, knowing their dip, determined the horizontal and vertical components of movement along the fault. Subsequent •diamond drilling based on Campbell's work located the presumed correlative of the Giant shear-zone system on the Con-Rycon and Negus properties, where it has been named the Campbell zone or system. At the present time, all production at the Negus Mines property is coming from orebodies along the Campbell zone."

Jan 1, 1950