Search Documents

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Mohsen Amir-Rahmat

The ore of Sarcheshmeh copper deposit that has been located in the south ?east of Iran, contains four type of rock that they have their specific hardness and strength according to their alteration type and mineralization. Blasting of these various types of mine rocks prepares various types of size for the product of mine as the feed of concentration. Along the crushing of this feed a few factors effect on the efficiency of the crushing unit. The aim of this project has been the consideration of the effect of ore size on the efficiency of crushing unit. For this investigation along the year 2000 A.D., six sample from feed and six sample from product of crushing unit have been prepared. The results of the screen analyze of these samples has shown that the size of feed has been lesser than the primary plan and the size rate of the product has been bigger than the primary plan. Also in this research the effect of feed size on the quality of product size has been considered.

May 1, 2003

By J. H. Crocket, J. Andy Fyon

"All gold deposits within the Tisdale Group are spatially associated with carbonate alteration zones; however, not all carbonate alteration zones are host to gold mineralization.Within the komatiitic and magnesium tholeiitic volcanic rocks at the base of the Tisdale Group, discordant and stratabound carbonate alteration zones occur throughout. The alteration zones consist of a ferroan dolomite - quartz inner assemblage which is enveloped by calcite-quartz and an outer chlorite-rich subzone. Factors which control the distribution of carbonate alteration include joint systems, flow contacts, synvolcanic faults and bulk composition of the host rock.Two environments of carbonate alteration can be recognized: 1) The subsea-floor alteration zones developed within the volcanic rock succession where hydrothermal fluids did not discharge directly onto the sea floor. Insignificant gold production has come from this alteration environment. 2) Seafloor zones, which represent points of hydrothermal fluid discharge into the hydrosphere, are spatially associated with felsic volcanic rock complexes and are host to syngenetic, auriferous cherty dolomite.Carbonatized, magnesium tholeiitic basalts, which are host to the auriferous, cherty dolomite, are enriched in antimony (>0.35 ppm), boron (>30 ppm), gold (>5 ppb) and lithium (> 35 ppm), but are depleted in copper ( < 70 ppm), with respect to carbonatized basalts not associated with gold. Orerelated, altered komatiitic flows can be screened using gold (>5 ppb), lead(> 10 ppm), arsenic(> 70 ppm) and antimony (>1 ppm).The habit, petrographic characteristics and certain geochemical characteristics of the altered volcanic rocks suggest that the hydrothermal fluid was of sea-water origin."

Jan 1, 1982

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By W. M. Brewer

Introduction This paper describes some of the mineral resources that are tributary to that portion of the Pacific Great Eastern railway included in the Western Mineral Survey District, No. 6, of British Columbia. This district extends 38 miles northerly from Squamish, the ocean terminus of the railway at the head of Howe sound, to Alta lake. Beyond Alta lake the railway continues northerly through two other mineral survey districts: the Central Mineral Survey District No. 3, and the Northeastern District No. 2. District No. 6 includes that section of the Coast Range from which the waters flow southerly towards Howe sound. The division between District No. 6 and District No. 3 is represented by an imaginary line across the summit between the headwaters of the Cheakamus river, flowing south into the Squamish, and the Green river which flows north and empties into the head of Lillooet lake near Pemberton meadows, about 20 miles from Alta lake. History: - The history of the route of the P. G. E. railway dates back to the old Cariboo days when a pack-horse trail traversed the country northerly from Squamish to the Pemberton meadows, and also south-easterly from Squamish to the head of Seymour creek, thence southerly down that creek to the north arm of Burrard inlet.

Jan 1, 1925

By P. Mark. Hawley

Development of Barrick Gold?s Pierina Gold Mine in north-central Peru requires construction of a waste dump for disposal of non-ore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high quality, hard, durable, blocky waste rock. A hybrid dump design concept was developed that requires in-pit segregation of high and low quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included. This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems.

May 1, 2002

By Sib N. Mukherjee

Main ventilation fans are used in all the mines and they run continuously 24 hours a day and 365 days in a year. Any improvement in their performance can lead to considerable power saving. The basic principle for selection, operations, and related measures are discussed in brief in the paper. The contributions of different elements of mine fan on its performance are discussed in brief. The means to improve efficiency of a running fan is also discussed and the importance of saving even 1 Kwh is elaborated. It is found that the cost of the energy saved may even permit a replacement fan to be procured in a few years time.

May 1, 2007

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By T. H. Etsell, P. C. Holloway

The fly ash produced by oil sands operations in northern Alberta represents a large, high-grade, potential resource for vanadium production in Canada. After extensive batch testing at the University of Alberta, a conceptual process flowsheet for the recovery of vanadium from oil sands fly ash has been developed. The various unit operations for this process, including decarbonization, roasting, leaching, desilication, precipitation, salt recovery and byproduct recovery, are described. Processes for the recovery of molybdenum and ammonium chloride from waste streams from this process, are proposed, as are potential uses for the ash residue; these byproducts represent significant potential sources of secondary revenue while reducing the environmental impact from the process. A preliminary economic analysis for vanadium recovery from oil sands fly ash using this process is also included and several major economic factors influencing its commercialization are discussed.

Jan 1, 2004

By Donald A. Cranstone

Donald Cranstone holds B.Sc. (Honours) and M.Sc. degrees in Geology from the University of Manitoba and a Ph.D. in Economic Geology from Harvard University. He has worked as a mine geologist, a provincial geological survey geologist and as a senior exploration geologist. He joined what is now the Minerals and Metals Sector of Natural Resources Canada in 1971, where he has been a commodity specialist for gold, for copper and another 28 metals. He is a senior mineral economist, currently engaged in analysis of mineral exploration and discovery success in Canada and of the future of the Canadian mining industry. Abstract This paper examines the history of Canadian non-petroleum mineral production. The outlook over the next 25 years, for mining in Canada and in each province and territory, is reviewed. The outlook for mining in Canada and in most provinces/territories is favourable, but problems seem likely in a few jurisdictions unless new orebodies are brought into production. In terms of exploration potential, Canada consistently ranks among the top three countries in the world. Over the last eight years, Canada has consistently been second only to Australia as a destination for exploration investment. For the first time, Canada is ranked in terms of total mineral production, including coal and construction materials, relative to all the countries of the world including countries of the former communist bloc.

May 1, 2001

By D. Milne

Laser profilometers exist for obtaining very accurate two and three dimensional profiles of joint surfaces. The application of this technology is not commonly applied to the collection of field data on discontinuity surface roughness. Rugged and portable field devices are not commonly used and the value of the possible field data that can be collected has not been well recognised. This paper reviews commonly used field techniques for assessing discontinuity roughness, discusses the value of this data and presents a new laser profilometer design for field application.

May 1, 2009

By Ross Gilders, Leo Cheung, C. David Desjardins

"For the past twenty years significant progress has been made in bacterial leaching. In fact, a recent article in the Northern Miner has cited that nearly all new copper production is based on bioleaching. The bacteria that play the predominant role in bioleaching is an obligate chemolithoautotroph called thiobacillus ferrooxidans. These bacteria thrive in areas rich in sulphide and prefer low acid media. In the simplest sense, they metabolize sulphide converting it to sulphate either as acid or as soluble metal sulphates. This process is well known because these bacteria generate acid mine water. Over the last five( 5) years, we have been carrying out development work on creating optimum bioleach conditions for the extraction of metals from sulphide rich ores and concentrates. Recently, a study was carried out on a byproduct sulphide concentrate produced in a tin flowsheet developed for the Mt. Pleasant Mine of ADEX Mining Corp. The objective was to determine whether a bioleach process might successfully leach this sulphide material which contains copper, zinc, iron and, what is more important, trace metals such as Indium, Gallium, and Bismuth. The current work describes the successful recovery of these metals achieving extractions of more than 80% by applying bioleaching techniques. An overview of this technical program forms the basis of this paper.IntroductionBio-Oxidation of metal sulphides has emerged to be one of the leading edge hydrometallurgical processes for the economic extraction of metals from ore and concentrates. The fundamental process involves the bacterial assisted oxidation of sulphide to sulphate yielding metal sulphates which can be subsequently leached by conventional means. The bacteria that play the predominate role is an obligate chemolithoautotroph named thiobacillus ferrooxidans (TF). These bacteria thrive in areas rich in sulphide and occur naturally worldwide. In fact, TF is responsible for generating acid in water (acid mine water) from exposed sulphide surfaces primarily through the oxidation of pyrite. TF bacteria thrive under the proper conditions of temperature and oxygen supply in the presence of sulphides and populations in excess of a million per millilitre (ml) of solution are achievable. Typically, at room temperature, the bacteria will bio-oxidize in a pH range of 1.0 to 3.0. Today, bio-oxidation has been applied commercially with great success for the extraction of uranium, copper, and gold."

Jan 1, 1996

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta&apos;s sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region&apos;s gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton&apos;s current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton&apos;s current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By Richard Morland

The Ekati Safety Guarantee is a conversation that has been taking place at Ekati for the last two years. It is a challenging, confronting, inspiring conversation which encourages people to see and pursue the possibility of guaranteeing that nobody who works at Ekati will be seriously injured or killed at work. The conversation takes us out of the normal, incremental approach to safety improvement; it takes us out of the world of striving, of seeking, of trying, and allows us to stand in, and be a stand for the future possibility of Zero Harm. It requires an unreasonable stand for, and commitment to, our own safety and the safety of our colleagues. A Powerful Conversation The safety guarantee began with conversations between executive team members and has been propagated regularly through the line through management meetings, pre-shift meetings, during workplace inspections, job safety observations, job and project planning, orientation and induction sessions, and when opportunities present themselves. This is a conversation that continues outside of Ekati with family, with government, with community members. It is a stand for safety as a value. The conversation about the safety guarantee is now pervasive at Ekati and forms part of a framework of initiatives that have led to sustained improvement in safety performance. During the last two years, the recordable injury frequency at Ekati has dropped to its lowest level in Ekati?s history. At the same time, job safety observations have increased from 500 per month to 4000 per month, whilst the overall number of people at Ekati has reduced by 30%. It has led to new ways of thinking about the conduct of operations. It influenced the 2008 upgrade of the Ekati process plant, resulting in the development and implementation of a crane lift protocol that eliminated injuries during over 100 lifts in two weeks, in an area of difficult geometry and with multiple entrances. It created space to successfully conduct a challenging commissioning period for the process plant crusher, during which time the machine was disassembled and reassembled several times, without incident or injury. No production pressure was permitted to interfere with this work, in line with our stated aim that we wanted everyone involved to guarantee that they would not be seriously injured or killed?our people had the space to do the work at a pace, and in a way, that guaranteed this outcome.

May 1, 2010

By Victor Rudenno

"Previous methods have employed statistical analysis to model future mineral resources. The method presented in this paper uses Zipj&apos;s Law to determine the size and grade of tin deposits still to be discovered. The law is applied independently to both known deposit tonnage and grades. A probability distribution for both &apos;tonnage and grade is computed/or those deposits still to be located and then, by applying a correlation between tonnage and grade, a distribution of the probability of metal content discovery is obtained.By considering an economic cut-off in metal contained in a deposit, the probability of economic success for the next tin discovery is computed, both for a world discovery and for the special case of Tasmania, Australia. The results indicate a probability of 11-37% on a world-wide basis and 18% chance of economic success in Tasmania.IntroductionIn the past , most attempts to determine the probability of success in finding an economic mineral deposit have relied on the accumulation of statistical data. These data are then used to predict a suitable frequency distribution to assess the probability of finding a deposit of a given size and grade (Singer,1975).The method not only relies on one having sufficient data, but also on the assumption that the data are not biased and that the distribution (usually log-normal) is a correct one. The method presented in this paper, to analyze tin deposits, uses Zipf&apos;s Law, which has been recently applied to oil, uranium, lead-zinc and gold deposits by Folinsbee (1977) and to Western Australian gold deposits by Rowlands and Sampey (1977). Tapp and Koniuszko (1978) have applied Zipf&apos;s Law to mineral distribution patterns in the Northern Australian orogenic provinces, which has enabled them to make predictions with a relatively small data source."

Jan 1, 1981