Search Documents

By A. Ismail

"The paper takes its material from three peat mining and power project feasibility studies sponsored by CANMET and conducted by Montreal Engineering Company Ltd. in the years 1976 to 1980. The role which peat may play in the Canadian energy prospectus is outlined, estimated and measured fuel peat resources are tabulated, and the economic and technical feasibility of mining peat for power generation is reviewed Recommendations are made for future work, and construction and disbursement schedules are developed for a combined peat mining and power generation project. The relationship between the mining of moss and fuel peat is discussed.IntroductionWhereas moss peat has long been produced in Canada, and exported for horticultural use , the underlying fuel peat has received little attention until fairly recently.In the seventies, however, the deepening oil crisis spurred Canadian interest in Irish, Finnish and Russian experiences in the utilization of fuel peat. Among others, Energy, Mines and Resources Canada had long been alive to the possibilities which indigenous peat offers, and in 1976 the Canada Centre for Mineral and Energy Technology (CANMET encouraged a proposal from Monenco to carry out a preliminary study and submit a report on the "" Assessment of Canadian Peat as an Alternative Fuel for Power Generation"". The report was submitted in April 1977. This was the first of a series of studies, and the authors of this paper were involved in its preparation.The escalating price of oil and the increasing problem of relying on its availability have combined to make alternative fuels more attractive. Peat, like other fuels previously uneconomic because oil was cheap, is now progressively gaining in viability. In addition to these factors, the utilization of peat has the following advantages: improvement in the country's balance of payments, by virtue of burning an indigenous fuel;creation of local employment for the mining of peat; improvement in land utilization;peat is a relatively clean-burning fuel, with low sulphur and ash contents."

Jan 1, 1980

By Nick Vayenas

This paper discusses the application of a commercially available state-of-the-art PC discrete-event simulation modeling software, called Promodel, for simulating a typical underground mine hoist system in the Sudbury mining region, in the province of Ontario in Canada. The reasons for using Promodel as a two-dimensional simulation development tool is its simplicity in use and its capabilities to provide enough flexibility to meet the modeling requirements of a mine hoist system. General information of a mine hoist system was collected for building the model. Example of the model?s output is also presented. The application of Promodel in underground mining offers a powerful, two-dimensional simulation environment in an affordable price for mining engineers to analyze and study operational problems. This hoist simulation model is an intuitive demonstration of the mine hoisting elements and the operational logic of the hoist, based on which optimization of the entire mine system materials flow can be considered as part of a mine cycle management feasibility study.

Oct 1, 2009

By D. J. MacDonald

UNDERGROUND development at the Lynn Lake property of Sherritt Gordon Mines, Limited, was begun in 1948 with the sinking of the A shaft in the area of the A orebody. By June, 1949, the shaft was completed to a depth of 1,024 feet. Twelve stations were cut, with the bottom level at 992 feet below the collar. Since completion of the shaft, lateral work has been carried out on the 12th level in order to expose the known orebodies and to provide openings from which deeper exploration could be conducted. Dur¬ing the change-over from sinking to lateral work, preliminary diamond drilling was done from the 12th level station to locate the A? ore-body. Later, drilling was carried out from the 5th and 9th level sta-tions, where, also, the outline of the A orebody was established. As the work progressed on the 12th level, and with the commence-ment of drilling below that level, the geological picture was found to be complicated by numerous faults. Instead of operating two drills it became necessary to use at least four. The original plans had provided air sufficient to drive two headings and to operate two diamond drills. The addition of two more air-driven drills resulted in a serious shortage of power.

Jan 1, 1951

By Theophile Yameogo

Much has been said about the methodology of geomechanical design in underground excavations. However, the geological, hydrogeological and geotechnical complexities encountered at the production horizons in the Athabasca Basin commanded for a novel approach in the geomechanical assessment and design of underground openings. Rock mechanics engineers at Cameco McArthur River have been able to establish a practical methodology that goes beyond known conceptual approaches. In this paper, the author describes the original challenges and unique approach in the geomechanical assessment for drifts and chambers development. The example of the successful development of the 510-8225N Chamber will also be presented.

Aug 1, 2010

By P. Keller, T. E. Lister, G. G. Clark, L. A. Diaz

As electronic technology continues to evolve there is a growing need to develop processes which recover valuable material from antiquated technology. This need follows from the environmental challenges associated with the recovery of raw materials and fast growing generation of electronic waste. Although present in small quantities in electronic devices, the availability of raw materials such as rare earths and precious metals becomes critical for the production of high tech electronic devices and the development of green technologies (i.e. wind turbines, electric motors, and solar panels). Therefore, the proper recycling and processing of electronic waste presents an opportunity to stabilize the market of critical materials, providing a proper disposal and treatment of a hazardous waste stream. This paper describes the development and techno-economic assessment of a comprehensive process for the recovery of value and critical materials from electronic waste. This hydrometallurgical scheme aims to selectively recover several value streams (base metals, precious metals, and rare earths) present in electronic waste. The economic feasibility for the recovery of rare earths from electronic waste is mostly driven by the efficient recovery of precious metals, such as Au and Pd (ca. 80 % of the total recoverable value). Rare earth elements contained in magnets (speakers, vibrators, and hard disk storage) can be recovered as a mixture of rare earth oxides which can later be reduced to the production of new magnets.

Jan 1, 2016

By Chris Cross

A working group from Anglo American, BHP Billiton, Rio Tinto and Xstrata reviewed supply and demand for graduates from mining education departments in countries where they normally recruit: Australia, Canada, Chile, Western Europe, South Africa and USA. Departments are typically small and increasingly unsustainable, resulting in a steady rate of closure. Supply and demand for graduates in the minerals industry is cyclical, with supply lagging behind demand and trending downwards. Currently, supply is tight and the industry is trying to expand with an ageing workforce. Greater collaboration between universities and within the industry is recommended to address these issues.

May 1, 2006

By Frank Mucciardi, Louca Gourtsoyannis

"Low and inconsistent recoveries of aluminum in the production of aluminum-killed steels triggered an extensive research program on the aluminum dissolution kinetics at McGill University. This research program led to the understanding of the melting kinetics and the hydrodynamics of making additions to liquid steel. It showed the necessity of gradually releasing liquid aluminum at the bottom of the ladle to increase aluminum recoveries.This knowledge was verified in practice at Sidbec-Dosco, where a prototype aluminum wire injector was developed and installed for the first time in Canada. The industrial application showed the validity of the theoretical and experimental results and provided further data for the mathematical modelling of the process.The development of the theoretical understanding, the industrial results, and the interaction between university and industry are presented.IntroductionAluminum is an extremely effective deoxidizer of molten steel; nevertheless, an efficient method of adding it to steel has eluded steelmakers for many years. It is well known that the recovery of aluminum used in the production of aluminum killed steel is both low and eratic, especially when the aluminum is added in the form of bars or lumps from chutes into filling ladles, a practice still common in many of today's steelmaking operations.As the density of aluminum is only about 40010 that of molten steel, it is conceivable that loose bars of aluminum simply ""thrown"" into a filling ladle will resurface before any appreciable dissolution of the aluminum has occurred, particularly if the depth of penetration of the additions is small. Before one can conclude that this is indeed the case, it is necessary to know the melting kinetics of an aluminum addition. Back in 1972, this information was not available; hence an extensive research program which focused on melting kinetics was initiated at McGill University."

Jan 1, 1982

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By Zainelabdin Khalid Zainelabdin Elfaki

The influence of partially replacing cement with marble waste on the workability and compressive strength of concrete bricks was investigated. Three replacement percentages, 10%, 20% and 30% weight marble waste, were used with different curing times of 7, 14 and 28 days. Two specimens were prepared for each percentage and curing time. For this study, marble powder from the Mining House Company in Saudi Arabia was used. It was observed that the replacement of cement in Concrete brick with marble waste enhanced the loading strength and the workability of the prepared concrete bricks. It was also observed that 20% replacement of cement with marble waste was the best replacement percentage compared to the other replacement percentages tested. Marble waste from manufacturing companies, either in powder, sludge or slab form, has negative impacts on the environment. In contrast, reusing marble waste has both economic benefits (i.e., selling the marble waste) and lessening the need for raw resources.

Jan 1, 2014

By Li. L.

Backfilling has become a popular solution in underground mines around the world. It reduces environmental impact of mining industry and improves ground stability. In most cases, backfill has a high water content so that it can be delivered by pipes from a backfill plant on ground surface to underground stopes. Upon deposition in the stope, the backfill tends to consolidate under its own weight, leading to a generation of excess pore-water pressure. To avoid excessive pressure and protect the backfill barricade installed at the base of the stope, the backfilling of the stopes is usually divided into two stages: plug pour and backfill body pour. The interruption of backfilling operation is undesirable as it slowdowns the mining productivity, and sometimes causes pipe clogging, leading to unexpected increase in manpower cost and further reduction in mining productivity. The backfilling interruption time may be reduced, even eliminated if the drainage of backfilled stopes is sufficiently improved. This paper presents an application of wick drains, a material commonly used in civil engineering, to mine backfilled stopes to help accelerating the drainage. A protocol is proposed for installing the wick drains in a mine stope to be backfilled. Numerical simulations were made, showing that the drainage of the backfill can significantly be improved by the introduction of wick drains. The application of wick drains in mine backfill can thus be considered as a promising technique and merits deeper and more detailed investigation.

Aug 1, 2013

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By D. Laguitton

"Mathematics, process theory, process practice and computer applications are the main disciplines that contribute to developing useful techniques for computer simulation of mineral and coal processing plants. As in any multidisciplinary effort, communication or transfer mechanisms must be developed to facilitate the flow of experience between participants of different backgrounds. These mechanisms include written reports, verbal communications, workshops and transfer of computer programs. The SPOC project at CANMET is devoted to computer simulation and as such has addressed, or will address in the near future, problems inherent to methodology transfer. The first major output of the project was the material balance program, MATBAL2, which has been acquired by over 30 organizations. Program documentation, industrial workshops and summer student programs have been used to effect the transfer. This experience is discussed and the future outlined.IntroductionComputer simulation has become a common tool in many different fields of human activity during the past two decades, as illustrated in Figure 1. The total number of articles abstracted in Chemical Abstracts under the general subject entry of “Simulation"" has been following a pseudo-exponential growth since 1972 and was approaching 5000 in 1980, whereas no such entry was even used prior to 1967. This represents over a dozen papers published daily on the subject and should continue to grow to higher figures. Still, progress toward accepting modelling and simulation in mineral and coal processing has been very slow. It will be shown later that this slow acceptance is a cause rather than a consequence of the limited success of the various attempts made so far to draw unambiguous benefits from simulation applications. The real cause of the difficulties in fully accepting the new methodology lies in the multidisciplinary aspect of modelling and simulation, which does not suit the traditionally conservative approach that prevails in designing and operating large and costly processing plants."

Jan 1, 1982

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

By Bill Charbonneau

Lumen, lm The measurement unit of light emitted by a light source 60W incandescent840 lumens 32W T8 linear fluorescent3200 lumens 54W T5HO linear fluorescent5000 lumens 400W metal halide24,000 lumens

Oct 1, 2010

By Charlie Graham

Our Approach ? Industry Trends ? New Forces at Work in Mining ? Deep Mining ? Energy projects ? Air power ? Hydraulics ? Electric alternatives ? Drilling ? Productivity ? Conclusions ? Transportation ? References

Oct 1, 2010

"Block caving is the preferred underground mining method to profitably extract massive, low-grade orebodies; however, lack of cave access inhibits understanding the rockmass response to mining, which is needed for safer, more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualization (VRSV) is an alternative method for understanding complex cave behaviour, by providing virtual access to the cave. A customized VRSV module was developed at UNSW Australia to investigate rockmass response to undercut developments at a case-study block caving operation. Time/sequence effects are investigated in rockmass response to blasting, which is an important factor in hard-rock mines.RÉSUMÉ La méthode d’extraction souterraine par blocs foudroyés est la méthode préférentielle pour extraire rentablement des gisements massifs à faible teneur. Toutefois, le manque d’accès à la chambre restreint la compréhension de la réponse de la masse rocheuse à l’exploitation, ce qui est nécessaire pour obtenir des opérations plus sécuritaires et plus productives. La combinaison de grands ensembles de données de multiples sources avec la visualisation scientifique par réalité virtuelle (VRSV) constitue un autre moyen de comprendre le comportement complexe de la chambre en fournissant un accès virtuel à la chambre. Un module de VRSV sur mesure a été développé à l’Université de Nouvelles-Galles du Sud (UNSW) en Australie afin d’étudier, dans une étude de cas d’une exploitation par blocs foudroyés, la réponse de la masse rocheuse aux développements de galeries de sous-cavage. Les effets de temps/séquence sont étudiés dans la réponse de la masse rocheuse au sautage, ce qui est un facteur important dans les mines de roches dures."

Jan 1, 2016

By Lloyd Rowson

??Several factors have led to a review and reoptimization of the Midwest uranium deposit by AREVA Resources Canada Inc., the project operator, on behalf of the owners ??The current proposal is to mine the deposit using open pit methods and then transport the ore by truck on a dedicated road linking the Midwest site with AREVA?s McClean Lake Operation (JEB mill) for processing ??A decision has been made to begin mining the deposit by 2010 (pending regulatory approvals)

May 1, 2008