Search Documents

By U. Troncoso

Mantoverde is a heap leach-SX-EW operation that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has been steadily increased to reach 62,000 ton in 2005. The forecast copper production for 2006 is 60,300 ton for an ore treatment rate of 9.5 million ton. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. Several improvements in the heap leach process have been implemented to cope with the higher ore throughput and copper production. However, the solvent extraction plant has remained unchanged which has resulted in a lower availability of raffinate solution and, as a consequence, in longer leach cycles. Different studies have been undertaken in order to optimize the solution management system at Mantoverde, including column test work aimed to reduce the leach cycle and solvent extraction plant modifications aimed to increase the raffinate solution availability. The test work program and the economical evaluations carried out, as well as the conclusions and recommendations obtained, are discussed in this paper.

Jan 1, 2007

By John C. Loretto

"Answers to some of the problems ofRecovery and Metallurgical AccountingIn Gold and Silver Hydrometallurgical PlantsThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the Metallurgical Test work figures and secondly, the Metallurgical Accounting figures do not balance.The plant results not agreeing with testwork figures are mainly due to:a) The testwork samples were not representative of the eventual plantfeed;b) Misinterpretation or misunderstanding of testwork;c) Plant losses;d) Plant design not allowing testwork results to be achieved;e) Operating deficiencies.a} The testwork samples being dissimilar to the plant feed occurs on a very high proportion of projects. The effects of this can beccr.ie exaggerated because the upper levels of the mining company often regard the original testwork figures as sacred and therefore base their judgement of current plant performance on these figures.Frequently the test work samples represent only a minor part of the orebody or alternatively a single composite of the whole ore body is used for the testwork long before it has been determined that all of the potentially different ore zones behave in the same manner. These errors can be compensated for by repeating the ""testwork tests 11 on current plant feed on a routine basis and using these tests to determine whether or not the plant is operating satisfactorily."

Jan 1, 1982

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By K. Parameswaran

This paper builds on presentations made at the Conference of Metallurgists (COM) 2015, COM 2017 and Extraction 2018 and associated papers published in the respective conference proceedings. Based on the classic Brundtland Commission definition of sustainable development as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper describes how metal mining can be compatible with sustainable development and how sustainability considerations have been applied in the primary copper industry, using several examples of sustainable mining practices from ASARCO LLC operations. Finally, the paper discusses how these considerations might be used in the future by discussing the need for developing a sustainable development strategy and how this strategy can be aligned with the United Nations Sustainable Development Goals. INTRODUCTION The primary copper industry comprises: mining (also referred to as “extraction”); mineral processing (also referred to as “beneficiation, “milling” or “concentration,”) which includes leaching, solvent extraction (SX), crushing, grinding, froth and flotation operations; and metallurgical processing which includes smelting and converting; refining, which includes fire-refining or anode refining and electro-refining; and electrowinning (EW). There are two routes for producing refined copper: hydrometallurgical and pyrometallurgical. The hydrometallurgical route comprises mining (open-pit and underground), mineral processing (crushing and grinding — for heap leaching only; leaching and SX) and metallurgical processing (EW). The pyrometallurgical route involves mining, mineral processing (crushing, grinding and froth flotation) and metallurgical processing (smelting, fire refining and electro- refining). The primary copper industry is capital, water, resource and energy intensive with the potential for significant environmental impacts, if the environmental aspects are not properly managed. ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V (Grupo México) acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, SX-EW plants, a copper smelter in Arizona and a copper electrolytic refinery in Texas.

Jan 1, 2019

By Gordon Sparks, Lyle Kajner

"An often over-looked component in the assessed value of a mining property is the value derived from the ability of the operator to limit financial losses during adverse economic times (i.e. low market price, high energy prices, etc.) by suspending operations. Overlooking the value of this type of operating flexibility when conducting mine investment analysis may negatively bias the risk profile for the investment by over estimating the investment's downside potential, thereby effectively undervaluing the investment. This paper illustrates the nature of the value of operating flexibility and discusses how it may be explicitly quantified within the context of conducting stochastic mine investment analysis. IntroductionMining properties are evaluated using an array of techniques ranging from simplistic non-discounted payback calculation s to sophisticated, discounted-stochastic simulation. Stochastic simulation analysis is perhaps the most robust mine investment analysis technique as it not only provides an estimate of the expected value of the property, but also quantifies the associated risks (for examples of stochastic mine investment analysis, see: Billingsley and Yaychuk, 1986; Gentry and O'Neil, 1984; Munro, 1977; or Harris, 1970).The quantification of risk is important as it provides the necessary yardstick required to allocate the corporation's resources efficiently. Resources are said to be allocated efficiently when the corporation's expected long-term financial reward is maximized while at the same time minimizing its risk (see Hertz, 1968; or Markowitz, 1952 for in depth discussions on efficiency as it relates to investment policy). The efficient allocation of resources should be the objective of any rational corporation. Therefore, rational corporations should employ stochastic evaluation techniques when screening their investments."

Jan 1, 1992

By S. Pietruszczak, G. Su, T. S. Nguyen, E. Haghighat

"In this paper, the mechanical properties of Tournemire argillite are modeled using a mathematical framework which employs the microstructure tensor approach (Pietruszczak & Mroz, 2000). The experimental data incorporates the results of a series of triaxial tests (Abdi & Evgin, 2013) conducted at different orientation of bedding planes relative to the direction of loading. First, a plasticity framework is presented which involves the specification of the conditions at failure as well as the description of the irreversible deformation process. Later, a systematic procedure is outlined for identification of material functions/parameters involved. The paper is concluded by presenting the results of numerical simulations of the triaxial tests. It is demonstrated that the model can adequately reproduce the primary effects of anisotropy in the stable deformation regime as well as the onset of fracture.INTRODUCTIONThe understanding of the mechanical behaviour of argillaceous rocks is important in many types of geotechnical projects, including petroleum extraction, carbon dioxide sequestration as well as deep geological disposal of radioactive waste. In all these cases, the primary concern is the onset and propagation of damage due to excavation, transport of pore fluids and/or elevated temperature. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long-term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URL). Such an URL is situated in Tournemire, France, in an argillaceous rock formation, the Tournemire argillite. The Tournemire argillite is characterized by the presence of closely spaced bedding planes and exhibits a strong anisotropic behaviour, so that its strength as well as deformation properties are directionally dependent."

Jan 1, 2015

By Carol E. Jones

Outline ? Reclamation is a primary mitigation. ? Understand baseline environment and land use. ? Determine reclamation goals. ? Selecting reclamation technology. ? Determine technical risk. Reclamation ? Primary Mitigation ? Through land and water disturbance, mining can have significant local and regional environmental impacts. ? Impacts can also result from associated land use changes. ? Reclamation is a primary tool that the mining industry uses to manage its environmental impacts.

May 1, 2008

By F. Rosenblum, P. Spira

"Techniques were developed to determine the oxygen demand of sulphide ore pulps in the laboratory and in concentrators. The effect of variables which influence oxygen demand was studied, and it is shown that the oxygen demand is a measure of the degree of oxidation of the sulphide surfaces. It is suggested that in investigating the significance of oxygen in flotation, the oxygen demand of the pulp is a more suitable parameter than the dissolved oxygen content.Oxygen demand measurements are being carried out with a view to determining the effect of aeration on mill metallurgy and devising improved methods of predicting aeration requirements of sulphide ores.The importance of pulp oxidation in the flotation of massive sulphide ores has long been recognized. At the Noranda concentrator, chalcopyrite could not be floated satisfactorily without a pre-flotation aeration step because the necessary dissolved oxygen was consumed by the large amount of pyrrhotite in the ore. With aeration, pyrrhotite and pyrite were depressed by surface •oxidization, and the resulting thiosulphate level in solution gave a good indication of the end of useful aeration. 1'he present study was prompted by the need to find an alternative criterion for cases where recycled mill water may contain a relatively high concentration of thiosulphate. Preliminary experiments suggested that the rate of oxygen uptake by the pulp -its oxygen demand -might be a practical measure of the end point of aeration as well as a significant parameter in the flotation of massive sulphide ores.Although it has long been realized that oxygen is an important variable in flotation, analytical difficulties precluded detailed plant investigations. Measurements of' dissolved oxygen in mill pulps were first reported by Ralston(i) in 1929. A titration method was used, and because of the delay occasioned by the preparation of clear solution samples, the values obtained were believed to be low. It was quite evident, however, that pulps in the grinding circuit had a lower oxygen content than in flotation. More recently, Woodcock(2,3) used a polarographic probe to carry out oxygen surveys in six Australian concentrators and he generally observed a similar pattern. A large number of other solution parameters were monitored, such as pH, redox potential, reducing power, and reagent and metal concentrations, with the aim of detecting correlations among the measured variables. A few potentin.lly useful relationships were found ""or specific operations in certain plants."

Jan 1, 1974

By J. C. Glandus, N. Tessier-Doyen, M. Huger

The Young's modulus of bi-phased model materials (vitreous matrix containing spherical alumina inclusions) have been determined by two complementary approaches: experimental and analytical. If the matrix and inclusions exhibit close coefficients of thermal expansion, the experimental results lie in the vicinity of the lower bound of the Hashin & Shtrikman's model. If there is a dilatometric disagreement between the components, untypical behaviors, similar to those obtained for a family of industrial refractory materials, were observed when the temperature varies.

Jan 1, 2004

By D. F. Machuca-Mory

The new algorithm for high-order simulation of ore deposit grades termed HOSIM is based on the concept of spatial cumulants. The algorithm is tested using data from Apensu, a structurally controlled gold deposit in Ghana. The required high-order spatial structures are obtained from a training image or analogue of the deposit. Using the available drillhole data and training image, HOSIM realizations are able to model well the grades and geometry of the large and well sampled mineralized structures. However, under-sampled small structures remain difficult to model. HOSIM offers a promising alternative for the spatial simulation of complex non-Gaussian orebody attributes of interest.

Jan 1, 2011

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By Bahram Samani

The Bafq - Saghand ore belt (metallogenic zone) is the main region, where the major discovered Uranium resources are located. This belt is a unique Upper Precambrian terrane experienced Katanga ? Pan African tectono ? thermal events. The oldest sialic crust was formed during the middle Proterozoic and followed by K-granite intrusions of Lufilian Cycle (850-800 M.Y.).This event caused Tectono ? Magmatic ? Activization (T.M.A) characterized by intracontinental rifting and associated ore formations. This zone was considered as an iron ore belt in 1960s ? 1970s, and U ? Th ? REE belt in 1980s ? 1990s, but by new discovered of U ? Mo (Co, Au, As, Cu) mineralization is assigned as a U - Polymetal zone, hosting the full sequences of iron oxide (Cu, Au, U) ore forming groups. On the basis of detailed investigations this zone is characterized by the following peculiarities: This zone is the vestigial vessel of Gondwana basement, where the oldest granite and the first platform clastic cover is exposed. This zone is marginal part of Precambrian continental crust, consolidated in 1.3-1.0 B.a. The sub mature continental crust experienced Lufilian Orogenic and Katanga ? Pan African Tectono ? Thermal event by intercontinental rifting, and ore mineralizations. The ore forming stages were sequential processes, started by enriched mantle derived metallogeny, and ended by interaction of silanes/ HACONS (derived from outer core) with crust. The magnetite- apatite (REE, Ti) metallogeny developed from alkaline- ultrabasic magmatic differentiation, capable to from Au- Ni- Sulfide intrusive massifs during 850- 800 Ma. Degassing of silanes/HACONS from deeper level, not only caused mantle enrichment, and plume upwelling as a frontal load, but also played the main role to develop regional Si (-Na-K-Mg-Ca-Co3) metasomatism, and formation of U- Th- Ti- REE- (apatite, magnetite) deposits. The latest (583-510 Ma old) felsic magmatism was major IGU from U-Mo (-Co-As-Au-?Cu?) hydrothermal vein- type deposits. The albitite- type U- Ti- REE (Th) mineralization could be formed by interaction of ascending, and descending solutions along the deep- rooted structural conduits.

May 1, 2007

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler's ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By Brad Thrall

"Viceroy Resource Corporation of Vancouver, B.C. has recently developed the Brewery Creek Mine, an open pit heap leach gold mine 55km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797000oz) of gold. Ore processing employs the heap leach technology using run of mine ore. 1996 highlights included construction of 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1.46 gpt on to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon where winter site temperatures routinely reach -45 C for extended periods.IntroductionFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996. The Brewery Creek Mine is in Yukon, the home of the Klondike Gold Rush nearly 100 years ago. This is the only part of Canada not glaciated in the Wisconsin advance so there is oxide ore resulting from about 80,000 years of weathering -unique in Canada. Discontinuous permafrost is present on site and has required special consideration in the design. Winter temperatures dip below minus 50 C, demanding an approach to mining and leaching that is different than in more temperate climates.Project DescriptionThe mine comprises 8 shallow, largely oxidized gold deposits along a 7km corridor. An 8 year mining program will extract 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797,000 oz) of gold. The strip ratio will be 1.35: 1. Overall gold recovery is projected at 78%. There will be 2.3 million tonnes of ore placed on the pad annually, with an average of 2.57 tonnes (83, 000 oz) of gold recovered per year. Because of the cold winters, the mine will operate approximately 210 days per year, while the leaching process will operate on a year round basis. Run of mine ore is placed on the heap 150 days per year. The recovery process utilizes conventional sodium cyanide leaching , carbon adsorption, caustic desorption, and on-site smelting. Peak employment during mining is 145 and winter staff is reduced to 45."

Jan 1, 1997

By P. R. A. Andrews

"The sillimanite group minerals, kyanite, sillimanite and andalusite are identified as alumino-silicate minerals with the common chemical composition AIP3.Si02' so that each possesses similar physical properties. Kyanite is the most abundant mineral and mainly occurs in Quebec, Ontario and British Columbia; sillimanite occurs in Ontario and Manitoba; and andalusite in Nova Scotia. The main use for the sillimanite-group minerals is in refractory applications for the production of refractory bricks and shapes. In refractory applications, the main performance criterion is the relative percentage of mullite formed within the material during firing. This phase gives a greater degree of resistance to creep deformation and slag attack, and improves the ability of the refractory to withstand high temperatures under load. The beneficiation of refractory silicate minerals has been the subject of many investigations at CANMET, and the former Mines Branch. Eighteen kyanite, two sillimanite, and three andalusite evaluation studies were conducted between 1933 and 1987. A review of some of the more important studies is presented, which includes information concerning mineralogy, beneficiation methods and flotation data."

Jan 1, 1995

By M. C. Bluteau, G. P. Demopoulos

Arsenic reports in the effluents of many non-ferrous metallurgical operations. The production of scorodite, a crystalline ferric arsenate, is considered as an attractive option for the fixation of arsenic from aqueous effluents. However, scorodite solubility and long-term stability in the pH region of interest for tailings disposal have not been thoroughly investigated. In this study the long-term stability of scorodite in the pH 5 to 9 region and the mechanism of scorodite dissolution were studied. Construction of eh-pH diagrams indicated that scorodite stability is highly dependant on the nature (stability) of co-existing iron-hydroxide/oxyhydroxide. It was also found that when scorodite dissolves, a ferrihydrite phase having very small particles size (nano-scale) forms and that the growth and crystallization of this material are delayed by the presence of arsenate even under accelerated (75°C) ageing conditions. Around neutral pH and ambiant temperature (22°C) scorodite seems to reach an equilibrium with ferrihydrite after 48 weeks yielding soluble arsenic concentrations < 5 ppm.

Jan 1, 2004

By S. Theobald

Semi-finished copper and copper-alloy products are typically produced by casting, subsequent hot rolling or extruding and further cold working by rolling and drawing. The technological properties of the products depend not only on the chemical composition of the alloys but also on process parameters such as annealing conditions and degree of deformation. In each production step, measuring and control technology is an important tool for optimizing processes and ensuring constant high quality. This paper follows the product all the way from testing incoming scrap packages, chemical analysis of melts, mould level control in casting, non-destructive testing technologies in cold forming processes, controlling geometrical properties in the production process, to the final tests of technological properties. All test methods are focused on the applications and requirements of our customers, as the examples show.

Jan 1, 2007

By S. Orzecki

The KGHM Copper Refinery Plant, Glogów 1, has operated for 35 years and -increased its capacity almost ten times.Cathode quality, expressed in terms of the total impurity content, has undergone a five-fold improvement. The present refining capacity is equivalent to 240,000 metric tonnes of copper cathode, with a total impurity content of 20 ppm, inclusive of 10 ppm Ag. These accomplishments result from combined implementation of current technological progress in electrolytic refining and KGHM&apos;s own solutions applied to the Glogów Refinery. The quality improvement measures feature both lowering actual current density, despite an increase in nominal current density, and diminishing the role of non-ion mechanisms which transfer impurities to cathodes. The paper contains a detailed discussion of these issues and outlines possible measures aimed at further production and quality improvements.

Jan 1, 2007