Search Documents

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

By D. Moffat

Rio Algom Limited has mined uranium at Elliot Lake, Ontario for 20 years. The production of this energy-generating element results in the need to dispose of low-level radioactive solid wastes and liquid effluents. Because of the wet-temperate climate at Elliot Lake, the liquid effluents are of particular importance. Radium-226 is the isotope which requires most attention, and the current practice for its control is by addition of barium chloride and retention of the resultant precipitates in large settling ponds. Analyses of typical effluents and waste streams are discussed and typical levels of radium-226, thorium-230, thorium-232, thorium-228, lead-2iO, polonium-2iO, and uranium isotopes are presented.

Jan 1, 1979

By D. C. Fuller

"CoaLiquid, Inc. (CLI) has been in the coal-oil-mixture (COM) business for over five years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August 1979. For over two years CLI has been expanding its efforts and conducting large-scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit.CoaLiquid has conducted commercial-scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.IntroductionCoaLiquid, Inc. officially dedicated its plant on August 31, 1979, at a ceremony presided over by the then Governor of Kentucky, The Honorable Julian Carroll. The dedication marked the culmination of over three years of research and development work and marked the beginning of a new era of coal-oil-mixtures as a commercial commodity in the marketplace. As the first such plant in the United States, it set the tone for construction to follow.CLI was originally owned and managed by a group of entrepreneurs from Kentucky who had developed the process and constructed the plant on purely private investment and conventional financing. Beginning in late 1976, with a pilot-scale operation, also located in Shelbyville, Kentucky (near Louisville), CLI began producing a stable mixture of 50070 coal, 30% to 40% oil and 10% to 20% water by weight. The technology employed was developed by Eric C. Cottell of Long Island, New York and is covered by U.S. Letters Patent No. 3,941,552. Since the pilot plant operation, CoaLiquid has made many refinements to its process and in fact has added new technology to its portfolio of patents and patents pending. Further refinements to the product now produce a stable mixture of 50% coal, 40% No.6 fuel oil and 10% water by weight."

Jan 1, 1985

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012

By A. Innus, R. Pelletier, C. Allaire

Refractory used for molten aluminium confinement is typically assessed separately for thermo-physical properties and molten aluminium resistance. This present work provides a case study comparison of four commercial refractory products that were subjected to a test procedure that combines mechanical impact, thermal shock with molten aluminium contact. The main conclusion of this work is that physical and mechanical property values by themselves do not, and cannot, predict the response of refractory to potential interactions between molten aluminium contact and thermal shock and mechanical impact. Adequate physical simulation is imperative to quantify the effect of such interactions.

Jan 1, 2004

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American?s suite of specifications for gearless mill drives (?GMDs?). These specifications are based on experiences in both Anglo American?s and others? operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Nov 1, 2011

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American’s suite of specifications for gearless mill drives (“GMDs”). These specifications are based on experiences in both Anglo American’s and others’ operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Jan 1, 2012

By P. A. Mascaró, N. Chacon, A. A. Cecchi

"This document shows the development of a system called the “On-line charge level determination in SAG mills” (abbreviated as Jc). The Jc variable has certainly been difficult to measure due to the relevant number of factors and variables that affect the grinding phenomena inside semi autogenous (SAG) mills. To assess the feasibility stage of the proposed system, it was necessary to carry out two tests in different sized SAG mills, 38´ × 22´ and 36´ × 15´, respectively. In each test, the system was configured with a battery of sensors of the following types: (1) strain gauge, (2) accelerometer, and (3) gyroscope. The first step involved for charge level determinations was to determine kidney foot and shoulder by means of a study of the energy-impacts on shell structures. The second step consisted of correlating the measured grinding operational variables with the actual charge levels obtained from SAG mill crash stops. This system development is extremely useful and relevant for providing approximations about mass balances inside SAG mills. It will be a suitable tool for explaining “tonnes per hour” variations and determining optimal points under various operating conditions.INTRODUCTIONThere has been a growing necessity for technologies capable of obtaining “on-line data” of the main comminution variables in order to increase throughput. Computer systems have taken an important role in providing important solutions by means of processing on-line device signals (commonly referred to as monitoring). In semi autogenous (SAG) milling, there are many examples of monitoring devices that allow the operational staff to obtain detailed information both mechanically and electronically inside a grinding circuit. In this context, a new technology has been developed to obtain “Jc total charge (%) online” in two different SAG mills called Vibro-Energy® System.As part of the analysis performed by JKsimMet® the Jb/Jc was estimated because it has an important impact on SAG mill throughput. Different scenarios were simulated and contrasted at various theoretical Jb/Jc values in a baseline circuit (Figure 1)."

Jan 1, 2016

By Robert B. Parsons

"Investors in flow-through shares are going to need an expanded road map to find their way through a growing maze of tax rules affecting such shares. At the end of 1985, no fewer than three new sets of important tax amendments were tabled which could have a significant effect on flow-through share issues. This proposed legislation is discussed this month in Tax Notes.IntroductionIn a flurry of legislative activity at the end of 1985, the federal government tabled legislation which includes the introduction of new rules which will have a notable effect on investors in flow-through shares and on companies that issue such shares.First, on November 26, 1985, Bill C-84, the legislation to implement most of the changes announced in the May budget, was introduced in Parliament. This legislation includes the rules for the $500,000 capital gains exemption, a matter of considerable interest to flow through share investors.Next, on December 2, 1985, the government tabled a Notice of Ways and Means Motion which would extend the time horizon for spending flow-through share funds to include the 60-day period following the calendar year. But all news was not good news. On December 4 the government released its proposals for a minimum personal income tax, which would include rules that would catch an investor's CEE expenses and capital gains."

Jan 1, 1986

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By J. Lu, D. B. Dreisinger, G. Houlachi

"Zinc metal is primarily produced by electrowinning from sulfate solution. Zinc electrowinning is very sensitive to impurities such as Co and Ni. These impurities have to be removed to produce high-quality zinc and maintain a high zinc current efficiency. Zinc dusts are used to remove these impurities by cementation. However cobalt cementation is extremely slow and it is typically activated by the addition of Cu and Sb. Even with the use of Cu-Sb activation, cobalt is still difficult to remove. The zinc dust used for cobalt cementation is negligible compared to that consumed for hydrogen evolution. In some plants up to 6-7% of electrolytic zinc is used for cementation. This is a great waste of energy. Cu-Sb activation is not well understood. The objective of this study was to further understand the Cu-Sb activation and then find a way to reduce hydrogen evolution and promote cobalt cementation. The investigation reveals how hydrogen evolution (or zinc dissolution) and cobalt cementation and re-dissolution change with temperature, zinc dust dosage, the concentrations of copper and antimony and time. In the Cu-Sb activation, copper is deposited on a zinc particle to produce a porous shell. The zinc particle as an anode dissolves while the shell as a cathode provides a place where cobalt cementation and hydrogen evolution occur and they are catalyzed by antimony. A certain level of antimony (around 0.1 mg/L) is a key to maintain the catalytic effect of the shell. At a higher antimony concentration, cobalt cementation is accelerated slightly while hydrogen evolution is increased greatly. When a zinc particle dissolves to a certain degree, cobalt loses its cathodic protection and starts to re-dissolve. The change in cobalt concentration is determined by the rates of cobalt cementation and re-dissolution. The operation conditions can be optimized to maximize the cobalt removal and minimize the zinc dust dosage.INTRODUCTIONMost of the world’s zinc metal is produced by electrowinning from sulfate media. Many impurities such as iron, copper, cobalt and nickel are co-extracted into solution with zinc. Iron, mercury, indium, lead and tin are removed by co-precipitation as hydroxides. Copper, nickel, cobalt, aluminum, arsenic and germanium are partially co-precipitated with iron while cadmium, magnesium and chloride remain in solution. Cobalt, copper, cadmium, nickel and etc. are subsequently removed by cementation with zinc dust to achieve an acceptable current efficiency and high purity metal product for the economical production of zinc. Zinc provides a strong thermodynamic driving force for the cobalt cementation:"

Jan 1, 2016

By Arne Renström

A fleet management system such as Minestar with CAES and Aquila could basically be defined as a tool for production control and distribution of drill and load maps, but should also be considered as continuous improvements and a never ending production study. The objective of production studies is to establish facts to be used for production improvements. In a mine operation there are many issues to improve and they spread from achieving productions plans, drilling precision, improved spotting while loading to equipment utilisation. This gives that there is not one single key value to present; we need to manage information presented on maps, as trends, graphs, tables and pre-calculated data for ?free-use? normally in spread-sheets to be able to turn data into useful information.

May 1, 2003

By M. McKim

"Due to the fact that there were no formal papers submitted for this session we can only print the discussions of the papers. a) Maqnetic Mill Liners : M. MckimE. MarcotteFalconbridge LimitedReplyIn looking at the slides on magnetic mill liners a question comes to mind, particularly in the case of a large diameter mill using large grinding media, concerning the potential hazzards which may exist from large chuncks of steel hanging in the mill. Would you comment.The magnetism was sufficiently strong from liner to liner to hold ........................ .(We are sorry but we could not transcribe the full reply to this question as no microphone was used by the speaker and i't was impossible for us to complete the rest).·"

Jan 1, 1984

By Marcel Laflamme, N. R. Rillette

"In 1982, a study was initiated to investigate relationships between bonus and accidents in Quebec underground mines. In 1983, the study was expanded to include the impact of age and experience on accidents.The paper will describe the methodology followed in gathering information at ten mines from three mining camps in the Province of Quebec, and its transfer to data banks for subsequent treatment. Multifactorial analysis of nine variable files for the ten mines has shown: that age, experience and seniority are linked; that total working hours are tied with overtime; that bonus is linked to the main activity of the miner, and not to accidents. The most tangible factors affecting accidents seem to be the introductory training and subsequent retraining at regular intervals."

Jan 1, 1989

Unplanned open stope hanging wall dilution is a significant cost for many open stope mining operations. Significant advances in empirical and analytical approaches for estimating stope dilution have been made, however, many important factors are still either ignored or assessed in purely subjective terms. There are many hard to quantify factors that simultaneously influence opening stability and dilution. This creates a significant difficulty for determining the influence of a single variable, such as exposure time, on opening stability. Open stope exposure time has been found to be one of the important factors that influences overall stope stability and dilution. A study is currently being conducted to quantify many of the factors influencing open stope dilution. The assessment of a large comprehensive case history database of Hudson Bay Mining and Smelting Co. Ltd. (HBMS) operations forms the basis of this study. This paper presents the findings of a study on the influence of stope exposure time on open stope dilution. The study is based on applying existing empirical stope dilution prediction methods to the extensive HBMS database. Minimising stope mucking time has been recognised as a method to significantly reduce stope dilution. Factors which influence hanging wall dilution, such as drill and blasting methods as well as undercutting the hanging wall, have been applied to reduce the scatter in the database. Empirical design techniques based on rock classification attempt to relate opening stability to ?stand-up time?, however, these approaches have not frequently been applied to the mining industry. Data from a ?stand-up time? graph have been interpreted in terms of an equivalent average depth of hanging wall slough and compared to the HBMS database findings. To add to the existing HBMS database, several stope case histories have been taken from Geco mine. These cases include data from very large open stopes with long exposure times. Data from all three sources suggest that hanging wall slough increases between .14 and 0.3 metres per month for a rock mass Q? value between about 4 and 13.

May 1, 2003

By J. Kuipers, R. W. Lawrence, P. B. Marchant, W. Brooks, J. T. Chapman

"Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes the commercial design details for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.INTRODUCTIONBioleach testing on a refractory carbonaceous sulphide concentrate from Austin Gold Venture (AGV), was initiated in late 1987 as part of an ongoing programme at Austin to investigate alternatives to concentrate smelting. Preliminary batch biooxidation tests at Coastech indicated that over 90% gold extraction by carbon-in-leach (CIL) cyanidation of the bioleach residue could be achieved, compared with less than 20% gold extraction on untreated concentrate by similar CIL processing.Subsequently, a more rigorous laboratory study was undertaken at Coastech to establish continuous biooxidation operating criteria on a bench scale. The objective of continuous testing in the laboratory was to provide confirmation of enhanced CIL response based on continuous bioleach products and to determine key process operating and design parameters for pilot testing. The success of the laboratory test program led to the installation of a mobile pilot plant at Austin Gold Venture. The plant was operated by Coastech and AGV during 1988 to provide scaleup data and design criteria for commercial design and feasibility analysis. Based on pilot plant operating data, a detailed commercial bioleach plant was designed as a possible retrofit to the existing 1000 tpd CIL plant. Capital and operating costs were estimated to provide a commercial feasibility study of bioleaching as an oxidative pretreatment for Austin refractory concentrate."

Jan 1, 1989

By Dillon. Patricia

Business Growth ?Coal ?Targeting 30 million tonnes by 2013 compared to 19 million tonnes produced in 2009 ?Expanding Energy Business unit (Oil Sands) ?Copper -Strong growth potential for existing operations and development projects ?New gold strategy recently launched ?New markets for zinc Need to retain existing and attract new employees to support growth Engaged Employee ?Has a positive attitude towards the organization and its values ?Is a person who is fully involved in, and enthusiastic about, his or her work Engaged employees are more likely to stay with the organization.

May 1, 2010

By I. Bakry

Uncertainty is an inherent characteristic of construction projects. Neglecting uncertainties associated with different input parameters in the planning stage could well lead to misleading and/or unachievable project schedules. The objective of this paper is to present a new approach towards scheduling repetitive construction projects while accounting for uncertainty. The paper presents an algorithm that quantifies anticipated delays resulting from different sources of uncertainty in the form of fuzzy time buffers. Through inserting the time buffers in strategic places in a time schedule, the algorithm provides protection against those main anticipated delays. The presented algorithm comprises two integrated components, a scheduling component responsible for producing a basic Linear Scheduling Method (LSM) schedule with deterministic activity durations, and a buffer component that handles fuzzy buffers sizing and insertion. The presented algorithm offers four different buffer insertion techniques covering different cases of interrelations between successive activities. The algorithm is implemented in a spreadsheet application, which automates calculations, yet allows users to fine tune the algorithm to fit the project at hand. With a focuses on highway construction projects as an example of repetitive construction projects, this paper accounts for sources of uncertainty such as weather, site conditions, change orders and equipment related delays. A hypothetical case is studied and explained to further demonstrate how the proposed algorithm works.

Aug 1, 2013

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003

By Selvia Tourn, Liliana Castro

"Abstract - Argentina, a large country with an important agriculture industry, needs an ever-increasing amount of phosphorus and potassium, as essential elements for plant growth. Current requirements are met from imports, but potential resources exist in Argentina. For example, several phosphatic occurrences are known in paleo-marine basins, the most significant of which are in Tertiary units in Patagonia. In addition, two types of potassium deposits are also known in Argentina: evaporite deposits in the Neuquén Basin at depths of 750 m to 1500 m contain 22 to 25 wt% K2O equivalent; and glauconitic sandstone containing about 6 wt% K2O has been identified in Patagonia.Several experiments were undertaken to test unprocessed phosphate rocks as slow-release, direct-application fertilizers, with good results. In addition, it is proposed that direct application of glauconitic sands would provide an efficient and economic alternative source of potassium. Tests with glauconite samples are still in progress. The existence of both phosphate and glauconitic rocks in Patagonia suggests that development of an extractive industry for these materials would not only help Argentina approach self-sufficiency in fertilizer usage, but also assist in the socio-economic development of this region."

Jan 1, 2003