Search Documents

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

MR. J. F. MYERS, Consulting J3eneficiation Engineer, Greenwich, Conn.: In the written discussion contributed by Mr. F. C. Bond in item ( 2) (page 515), speaiking about the significance of the ratio of mill diameter to the make-up ball diameter, he states: "When this ratio exceeds 100 the power and capacity of the mill are de-creased"; and the paragraph ends with a reference to the 30 per cent ball volume "with some de-crease in mill capacity". I believe this broad statement is incorrect. When we are dealing with a non-cataracting mill, pre-ceded by a good rod mill, there is a slight increase in capacity, but the power does drop. The second point that I consider needs consideration is Mr. Bond's item (8), Proper Mill Speed (page 516). This paragraph should be qualified to cover single-stage mills only. It does not apply where a rod mill is followed by a non-cataracting ball mill. The statement as is, with no qualification, gives an erroneous idea of proper mill speeds.

Jan 1, 1957

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By R. D. Brown

In view of the many changes which have taken place since 1950 in the rules of the Income Tax Act concerning the deduction of exploration and development expenses, many corporate taxpayers each year face the tedious task of determining which particular rules their unclaimed exploration and development expenses are subject to and in what sequence these expenses are to be claimed. Recent amendments to the Act have cleared up some of the mystery of the "ordering" of these deductions. This article examines the sequence in which various categories of exploration and development expenses are to be deducted in accordance with the terms of the Act as amended by Bill C-11.

Jan 1, 1978

By W. R. Richmond, T. S. Li, D. Ilievski

The reactive precipitation of ferrihydrite was studied in a laboratory semi-batch precipitator, where a highly concentrated sodium hydroxide solution was fed into an iron nitrate solution. Instantaneous hydrolysis of iron[III] takes place when the two reagents are mixed generating supersaturation, and leading to immediate precipitation of ferrihydrite via a primary nucleation mechanism then followed by limited crystallite growth to 3 to 7nm. A mathematical model of the semi-batch laboratory precipitator was used to simulate the pH responses during the precipitation of ferrihydrite at different reagent feed rates. The model comprised of interconnected compartments of averaged hydrodynamic conditions, incorporating physically meaningful turbulent mixing time constants. The precipitation process is described by the solute concentration conservation equation incorporating a postulated ferrihydrite primary nucleation model. It was found that the semi-batch precipitator model predicted the experimental pH response reasonably well. The experimental results demonstrated that the reagent feed rate has a critical effect on the course of the precipitation of ferrihydrite, i.e. it is a rate determining step given the fast hydrolysis and precipitation kinetics.

Jan 1, 2005

By A. Belleau, F. Lavoie

"Quebec Iron Ore Limited (QIO), a subsidiary of Champion Iron Limited (Champion), secured assets in early 2016 from the previous Bloom Lake operations in the heart of the Labrador Trough region of Northern Quebec, Canada. A plan was developed to bring the Bloom Lake facility back in operation once the iron ore market conditions improved. The project restart involved several aggressive moves to change operational effectiveness, one of which was the utilization of the existing Phase 1 Plant with an upgraded process flowsheet and equipment. The production target was 7.4 million tonnes per annum of 66% iron ore concentrate with an approximate 10% increase in iron ore recovery. The Phase 1 upgraded flowsheet was initially based on review of historical Phase 1 data and pilot testing data undertaken during the original Phase 1 operation and was finalized once additional metallurgical test work and process modeling was carried out by Mineral Technologies in late 2016. The final upgraded flowsheet is comprised of rougher spirals, rougher middling scavenging spirals, and an up-current classifier (UCC) with overflow scavenging spiral stage. A portion of the gravity circuit tailings treated by a series of wet high intensity magnetic separators (WHIMS) to boost overall iron recovery. This paper will describe the efforts taken to test and design the Bloom Lake Phase 1 upgraded flowsheet and report on the plant performance since commissioning in first quarter of 2018.SITE HISTORY The Bloom Lake iron mine property is located approximately 13 km north of Fermont, Quebec, and 10 km north of the Mont Wright iron ore mining complex, property of ArcelorMittal Mines Canada. The Bloom Lake mine facilities include a 32 km railway to efficiently transport the high-quality iron concentrate to a loading port located in Sept-Iles, Quebec. The Bloom Lake property was first explored in 1951 and went through multiple minor exploration campaigns by different companies up until 1998. A major exploration program was conducted by Quebec Cartier Mining (QCM) in 1998. This program included line cutting, surveying, diamond drilling, geological mapping, mini-bulk sampling, bench-scale preliminary metallurgical test work and preparation of a “mineral resource” estimate."

Jan 1, 2019

By Stuart McTavish

"The Brunswick Mining concentrator processes 10,000 D.S. T. per day of a complex sulphide ore. Four separate concentrates- zinc, lead, copper and bulk-are produced by selective flotation. Several major changes have been made to the Brunswick flotation circuit to improve the process and control. This paper will describe the present flotation practices at the Brunswick Concentrator. Special emphasis is given to the conversion of two of the primary circuits to an SO2-aeration flowsheet, and to the addition of a new secondary zinc flotation circuit that produces a zinc concentrate from the plant tailings. IntroductionBrunswick Mining and Smelting Corporation operates a zinclead- copper and silver mine and concentrator near Bathurst, New Brunswick. Since the start-up of operations in 1964, the flotation flowsheet has undergone major modifications to process the increased tonnages and to produce a greater number of concentrates. The flowsheet for the concentrator as it was in 1971 has been described by Neumann and Schnarru) and by Ersklneco. Since then, in 1971, the No.6 concentrator was converted from bulk flotation to selective flotation to produce a copper, lead and zinc concentrate. A separate zinc upgrading circuit was installed in 1972 and a bulk flotation or dezincing circuit, which reduced the zinc in the lead concentrate, was started in 1973. In 1976, the secondary zinc circuit was initiated.In addition to these new circuits, changes have been made to the existing circuits to simplify their operation."

Jan 1, 1980

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By H. S. Wilson

"The property owned by the Lamaque Mining Company comprises a group of forty-four claims and fractions occupying an area of about 2,458 acres, in west-central Bourlamaque township, Abitibi county, Quebec. It is on ,the outskirts of the towns of Bourlamaque and Val d'Or, about 70 miles east of Noranda, near the eastern end of the belt of greenstones of Keewatin and Timiskaming age that extends eastward through Kirkland Lake into northwestern Quebec, terminating in Haig and Jurie townships 40 miles to the east.The claims on which the orebodies occur were first staked in 1923; No. 3 vein was discovered the following year. The original discovery was made by R. Clark in 1923. This was a small quartz vein containing a pocket of coarse gold on the north side of a hill near the northwestern corner of block 3. It is said that all the gold was removed in one shot in blasting into the vein; elsewhere it was barren. A picket line was then run west along the strike of the vein, which occupied a narrow shear zone, and about 2,000 feet west, in prospecting on either side of the picket line, a large boulder of quartz and tourmaline containing visible gold was found. This led to more intensive prospecting by trenching in the vicinity with the result that the No. 3, or 'float' vein, about 250 feet north of the boulder, was found. Due to low ground this vein was exposed in only one trench. The only other important vein found on the surface was the No. 1, or H, vein, which was exposed in several places by stripping and trenching, but it did not carry appreciable amounts of gold."

Jan 1, 1954

By K. K. Panthi, P. K. Shrestha

"Displacement of rock mass around a tunnel opening varies according to the rock mass properties, insitu stress conditions and applied support in the tunnel. Such displacement is also altered by presence of bands of rock mass that differ in properties. This paper focuses on the deformation behavior of rock mass around tunnel openings at four tunnel sections in Kaligandaki headrace tunnel where extensive instrumentation was done. Based on the actually measured tunnel displacement records and actually measured support pressure; back analysis has been done to estimate rock mass properties and insitu stresses. Numerical analysis has been done to analyze and assess the deformation behavior of the rock mass around the tunnel sections.INTRODUCTION Instrumentation and monitoring of tunnel convergences have significant importance in evaluation of tunnel stability. One of the key aspects of monitored data is that early convergences can be used in estimation of long term convergence. In addition, these data can also be used in evaluation of rock mass parameters and in-situ stresses around the tunnel. Convergence around a tunnel periphery may vary according to rock mass quality. Presence of bands of different rock mass may hinder the displacement pattern in the tunnel. Particularly, displacement characteristic of tunnel periphery in schistose, foliated and deformed rock mass is altered by presence of bands of comparatively stronger rock mass, e.g., quartz veins or presence of shear seams or faults. Similar observations were also recorded in monitored tunnel sections in Kaligandaki headrace tunnel, located in the Nepal Himalayas. Extensive monitoring was done by installing multiple point borehole extensometers (MPBX) at three different locations of the tunnel periphery at four different tunnel sections. In addition, convergence measurements by tape extensometers and installation of pressure cells to record support pressures were also carried out at each of the tunnel sections. Observations showed that the tunnel convergences varied according to rock mass quality, in-situ stress and effective support pressure.Rock mass parameters and stresses have significant role in the extent of tunnel deformation, but these parameters are often unknown or difficult to predict. Back analysis based on actual tunnel displacement records and known support pressure is believed to be an important method in such endeavor. This paper performs back analysis to evaluate rock mass parameters and discusses correlation of rock mass behavior with tunnel deformation and applied support. For this purpose, the rock mass parameters are estimated from actual tunnel displacement records, mapped rock mass quality records and laboratory tested data. Then, numerical modelling is conducted to correlate post peak behavior of the rock mass with actual tunnel displacement."

Jan 1, 2015

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By George S. Martin, Michael D. Winship

"Placer Dome Inc. is the operator of the Musselwhite project located 100km north of Pickle Lake, Ontario. J.S. Redpath Limited was contracted to conduct an underground exploration program using shaft access.During the winter of1988, the shaft collar was established in 16 metres of water bearing sand and till overburden. This paper will illustrates the engineering techniques used to overcome the obstacles to installing a shaft collar in deep overburden. Specialized dewatering and piling procedures were employed.INTRODUCTIONHarold and Allan Musselwhite discovered gold in the Opapimiskan Lake area, north of Pickle Lake, in 1962. The prospectors were grubstaked by ten companies in 1973.A diamond drill program was initiated shortly thereafter.In 1983an underground ramp exploration program was carried out on the West Anticline portion of the property. The program was unsuccessful in establishing an ore reserve so surface exploration continued. In 1986the ""T"" zone was discovered. Further surface drilling was done and an over-all drill-indicated reserve of 6 million tonnes at 7 grams per tonne was outlined. The gold mineralization occurs in several vertical tabular deposits within the iron formation. In late 1987the joint venture partnership, now consisting of Placer Dome Inc., Inco Gold Co., Corona Corporation and Esso Minerals Canada, contracted J.S. Redpath Limited to conduct an underground exploration program on the ""T"" Zone.The scope of work for the project was to: 1. establish a 45 km winter road in 1988 and 1989;"

Jan 1, 1989

By Dennis V. Woods, J. Duncan Crone

"In order to determine its capabilities and to aid in the interpretation of fie ld results, a scale model study and field tests were carried out on the Crone borehole pulse electromagnetic (PEM) system. The model results indicate that if a borehole passes in the vicinity of a tabular conductive body, the system will not only detect the presence of the body, but will also return information as to its conductivity-thickness product, size, altitude and position.The effect of variation of these electromagnetic and geometric factors on the shape of the response curve from a borehole PEM survey is displayed by a number of suites of scale-model response curves. These model curves can be used directly as type curves in the interpretation of field results. Field tests of a prototype PEM system provide a check on the scale-model results and also summarize the procedure of interpreting field data using the model type curves.The borehole pulse EM system can be effectively used as a follow-up geophysical instrument for locating and delineating known conductive bodies. It can also be profitably utilized as a primary geophysical exploration tool in areas of deep mineralization below the depth limit of conventional airborne and ground geophysical systems. The probed area of a diamond drill hole in these cases is increased from a 1- inch drill core to a zone extending hundreds of feet from the hole."

Jan 1, 1980

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977

By Howard Keele

"The Whitewood Mine near Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Approximately 2 million tonnes of sub-bituminous coal is supplied annually to the Wabamun Generating Plant. A high water table, high groundwater pressure, and structural folds contribute to stability problems in the fine-grained overburden. Significant increases in coal recovery have been achieved in recent years through improvements in water management and mining methods. Agricultural capability of the post-mining landscape has also been improved following the completion of mining/ reclamation activities. Introduction The Whitewood Mine, located to the north of Lake Wabamun and seventy kilometres west of Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Figure 1 shows the location of the Whitewood Mine with respect to the city of Edmonton. The mine presently supplies two million tonnes annually of sub-bituminous ""C"" coal to the 582-megawatt Wabamun Generating Plant located adjacent to the mine. The area is characterized by a high water table-, rolling coal seams and an overburden that consists of muskeg, clay and various sedimentary layers of sand, gravel and fine-grained sandstone. These distinctive characteristics require careful attention in order to not only meet the coal delivery requirements of the Wabamun Generating Plant but also to do so economically. Historical Background A small-scale underground coal mine was opened in the Wabamun area in 1910 by the Conner Coal Mining Co. Ltd. Underground operations were continued by several operators until 1948 when the Alberta Coal Co. Ltd. opened a strip mine which was subsequently taken over by the Alberta Southern Coal Co. Ltd. in 1951. The small-scale strip opera"

Jan 1, 1985

By Stopford Brunton

For many years it has been accepted as axiomatic that the greater number of 'veins' or 'leads' in the gold districts of Nova Scotia are of the 'interbedded' type. The corollary to this hypothesis is that the vein or lead will have a continuous hanging-wall of one kind of rock, and a continuous footwall of the same or another kind of rock; but the essential point is that the foot and hanging walls are, according to this theory, both continuous and of uniform composition throughout; and that the vein or lead conforms to the bedding of the adjacent strata. With regard to the deposition of the gold in the rocks, the probability is that the key of the problem is contained in a statement by E. R. Faribault, of the Geological Survey of Canada: "The combined effect of cleavage, jointing, and stratification is to cause the rocks, especially the quartzites, to break into rhombohedral blocks". It is essential to comprehend that the rocks of the Province are no doubt folded into anticlines and synclines; but also it must be fully realized that the gold deposits and pay-shoots do not depend so much upon these as upon the fractures resulting from the disturbance caused by the intrusion of granite masses, and controlled by the combined effect of cleavage, jointing, and stratification. These fractures would form the channels through which the ore-bearing vapours and solutions would rise, and at the junctions of these fractures, where the fracturing was greatest, the easiest passages would be afforded to the ore carriers, with the result that the ore-shoots would be found at or near the intersections of fractures. It is a significant fact that in at least thirteen different districts throughout the Province, operators have at various times remarked upon the occurrence of rich ore at the intersection of 'leads,' 'veins,' 'beds,' etc.

Jan 1, 1928

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Carl Faessler

Abstract Some Canadian geologists believe chat, in the Grenville sub-province of Eastern Canada, there is no granitic intrusion older than the anorthosite. The writers are among those who hold the contrary view. They suggest a new means to distinguish between rocks belonging to intrusions respectively older (Laurentian) or younger (Pine Hill) than the anorthosite. This new method is based on microscopical observations which demonstrate that the Pine Hill intrusives contain a large amount of exsolution perthite, whereas the Laurentian intrusives are completely devoid of exsolution perthite. Where perthite is present in Laurentian rocks, it is the result of lacer hydrothermal replacement. Introduction The present paper is the result of a systematic study of some acidic intrusive rocks in the Grenville sub-province. These rocks underlie large areas of the Canadian shield in the Province of Quebec, mostly along the southern border of the shield.

Jan 1, 1946

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By John S. Stevenson

"Although we have no uranium- producing mines as yet in British Columbia, uranium, associated with gold and cobalt, has been found in two deposits in amounts such that the combined value of the metals not only warrants the further exploration of these deposits, but also encourages the search elsewhere in the Province for other similar deposits.Where uranium-bearing veins have been found in British Columbia, the uranium mineral is the crystalline variety of uranium oxide, uraninite, rather than the massive, non-crystalline variety, pitchblende, such as found in the Great Bear Lake deposit and in other similar deposits along the southwestern margin of the Precambrian shield.The principal occurrences of uranium known so far in British Columbia are associated with bodies of granodiorite and quartz diorite along the eastern side of the Coast Range belt of batholiths. In this part of the Province, interesting amounts of uranium occur on the Gem property in the Bridge River area and on the Victoria property south of Hazelton; and smaller amounts occur on the Red Rose, Rocher Debouze, Delta, and Ohio properties, also south of Hazelton. At the Gem and the Victoria, the uranium mineral, identified as uraninite, occurs in deposits that also contain abundant cobalt-nickel sulpharsenides, and molybdenite.At these properties, the uraninite occurs as clusters of small black crystals of sub-metallic lustre that may be seen upon careful -searching of a highly radioactive specimen with a hand lens. Under the microscope, the uraninite is seen to be in the form of cubes or modifications of cubes that may occur as individual grains widely scattered throughout the gangue or may be gathered into clusters of several grains. The grain size of the uraninite is in general small. Although a few clusters of grains are up to about 10 mesh in diameter, the individual grains, whether in clusters or widely disseminated, are rarely more than 400 mesh in diameter."

Jan 1, 1950