Search Documents

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By Dorothy Walters

As an increase in the number of producers alters fact ors affecting supply, long-term prospects in traditional markets for many minerals weaken. At the same time, conflicts between national and international objectives undermine existing competitive elements in mineral markets and Canadian costs escalate. Such changes may dramatically alter the environment in which the mining industry operates.

Jan 1, 1979

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006

By A S. Leitch

This paper is based on the accident prevention pro-gram carried out in the coal mines of Alberta. It defines the role of the Alberta Mines Branch and of The Work-men's Compensation Board, and relates how a safety pro-gram was initiated. The formation of the Alberta Class 1 Mining Safety Council is also described. The responsibilities of both management and the individual worker are then outlined, and the main features of a successful accident prevention program are delineated. T HE purpose of this paper is not to repeat generalities and platitudes about industrial safety, but rather to relate the experience of Alberta coal mines during the past number of years in their efforts to keep accidents to a minimum. It has been learned from experience that many basic principles are as sound today as they were 20 years ago. How-ever the complexities of modern mining methods and the modern man or miner have created problems that did not exist then.

Jan 1, 1964

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By S. G. Hardcastle

The effects of air velocity in promoting cooling through the evaporation of sweat generated when working at a high metabolic rate and/or in hot environments is well known. Many of the environmental heat stress indices consider the effect of air movement directly or indirectly within their determination, be it through the use of a specific instrument i.e. a wet-bulb globe temperature meter or Kata thermometer, or inclusion of in the calculation of a stress index, including the effective temperature, air cooling power, thermal working limit, ISO 7933?s predicted heat strain model. Within these models, ambient air temperature, relative humidity and barometric pressure are also considered in varying degrees to quantify an airstream?s capacity to evaporate sweat. Deep mine studies have shown cumulative increases in heat exhaustion rates with both decreasing air velocity and decreasing air cooling powers. However, despite a capacity to cool, the resultant cooling is very dependant on sweat production and its availability for evaporation; these are included where sweat rates and skin wettedness are considered. The first depends on hydration and physiological factors whereas the second is more an engineering factor related to the degree of clothing required. As sweat rates deteriorate with aging, the benefits of evaporative cooling potential can similarly be expected to be diminished. This paper continues to report upon on-going physiological studies exploring the potential for heat stress in deep underground mines through the simulation of mining activities in environmental chambers and a human calorimeter facility. The focus of this paper is to introduce preliminary data suggesting that increasing air velocity (0.5, 1.5 & 3.0 m/s) is beneficial for young subjects (22 ± 1 yrs), as indicated by lower core and skin temperature measures and heart rate during an intermittent work protocol, and then show a lesser benefit for older subjects (62 ± 2 yrs). Both subject groups performed the same task under the same environmental condition (35°C, 60% RH) wearing a standard mining ensemble. The study similar to others being performed under the Deep Mining Research Consortium funded research continues to provide evidence that a greater understanding of heat management processes is required and that worker education is critical as environmental measures and health and safety regulations may not be expected to include all demographic factors such as age, sex and health which are known to affect human thermoregulatory response.

Aug 1, 2013

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

"The Australasian Joint Ore Reserves Committee (JORC), which is sponsored by the Australian mining industry and its professional organisations, developed the JORC Code to provide minimum standards for public reporting. JORC was first published in 1989 and later incorporated into the Listing Rules of the Australian and New Zealand Stock Exchanges making compliance mandatory for listing public companies in Australia and New Zealand."

Jan 1, 2003

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By Roger Potvin

Abstract The demand for pure zirconium and titanium metals in Germany increased considerably during the war. Pure zirconium was used in flash bulbs, in vacuum tubes, and in time fuses for bombs, where it has a decided advantage because it gives no gas in burning. Under the form of alloy, it was used with other rare elements for making substitutes for platinum; it was also used as a scavenging agent in high-grade steels. Metallic titanium was mainly used in connection with the manufacturing of special alloys. The authors were sent to Germany by the Department of Reconstruction and have investigated the German process developed for producing these rare metals. They describe the procedure and special equipment used for their commercial production in Germany during the war. General Metallic zirconium and titanium were .produced on a commercial scale in Germany by the thermal reduction, with metallic sodium, of potassium fluozirconate and titanium chloride, respectively, using a mixed potassium and sodium chloride flux. According to the information gathered, the sole German producer of these rare metals in pure form was the Deutsche Gold und Silber Scheideanstalt (commonly called Degussa), at their Werk II, 215 Gutleutstrasse, Frankfurt/Main, which was visited by the authors on September 18th, 1945. As far back as 1934, Degussa was carrying on active research on the manufacture of zirconium, and nearly one ton of the pure metal had been produced before September, 1939. Concurrently, a quite similar process was worked out for the recovery of titanium and it was in commercial operation in the year 1938, during which the production totalled about half a ton (metric). The demand, especially for pure zirconium, increased considerably during the war, attaining a total of about 48 tons during the period October, 1939, to the end of 1944, and reaching a peak of more than 15 tons in 1943. In 1944, the plant was slowed down due to the frequent and disastrous bombing by the Allies, especially in March and September.

Jan 1, 1946

By Ian Thomson

OBJECTIVES OF EXPLORATION ? Prove/Disprove presence of potentially economic mineralization ? Keep on budget ? Minimize negative environmental impacts ? Gain a ?Social License to Operate? (SLO) WHAT IS A ?SLO? ? Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Approval (BSR and AccountAbility) ? Ongoing Approval, broad social Acceptance (Joyce and Thomson) ? Ongoing Acceptance (Nelson, and many others) ?Expression of the quality of a ?relationship?

May 1, 2010

By Thomas Glück

Established and emerging mining companies face significant challenges in managing their operations and projects. Outcomes often do not meet the expectations of all the stakeholders of particular developments. This paper reviews typical management practises used by mining companies to undertake mining projects and improve their operations. A simple application of the House of Quality (HOQ) tool used in the Quality Functional Deployment (QFD) management approach is presented. It is shown that a QFDMMPtg approach could lead to innovation in mining processing plant development practice.

Jan 1, 2015

By Michio Okada

Dissociative adsorption of hydrogen (deuterium) on thin gold films grown on Ir{111} surface has been studied with temperature-programmed desorption using a quadrupole mass spectrometer and nuclear reaction analysis. Thin Au{111} films are epitaxially grown on Ir{111}. Surprisingly, H2 (D2) can dissociatively adsorb on these Au{111} films, although it is well known that Au surfaces are noble enough not to dissociate hydrogen molecules [B. Hammer and J.K. Nørskov, Nature 376, (1995) 238]. We attribute this to the sensitivity of hydrogen to changes in the local surface properties, e.g., electron localization (the narrowing of the s-band, the s-band center model), which could explain the upto now unexpected high for the reactivity of a thin Au{111} surface. Moreover, we found that H (D) atoms can be confined into a Au thin film and/or the interface between an Ir surface and the thin Au film. We demonstrate how anomalously reactive thin Au films grown on an Ir surface are, and also compare the Au films with Ag films grown on Ir to test the validity/generality of our proposed s-band center model.

Oct 1, 2003

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007