Search Documents

By Stewart W. Daniel

"Increasing labour costs, the trend to larger mills, the processing of lower grade ores and a diminishing sup-ply of well-trained and experienced mill operators contribute to the necessity of automating a grinding circuit. With sophisticated process control techniques, supervision of the mill line is reduced to an occasional inspection by the shift supervisor. Process operating decisions and/or adjustments are quickly and accurately performed by the electronic devices to be described. When the variables in the grinding circuit are stabilized using the sensors and controllers as discussed, the over-all grinding circuit is maintained at its optimum grinding load level, with ample protection against under-and overloading."

Jan 1, 1967

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By Mauricio Olivares

About Largest combined Phosphate and Potash company in the world Corporate headquarters in Plymouth, Minnesota Publicly traded on NYSE under MOS

Aug 1, 2013

By R. W. Pugh, D. G. Bellow

"This paper will describe how cultivator shanks are made in one company and how the manufacturing was studied with a view to increasing product consistency and reducing manufacturing cost. The product: which is used extensively in the agriculture industry, was analyzed to determine which geometric parameters optimized its design and whether there was justification for the great variety of styles and shapes that are available in the market. Finally, an extensive series of field trials were undertaken which showed that it is advantageous to the manufacturer to be better aware of the loads and forces that his product is subjected to by another industry.IntroductionStelco maintains a Research Group for its Western Region operations headquartered in Edmonton, Alberta. Because of the small staff, a location that is isolated with respect to its Burlington, Ontario centre and a diverse set of processes and products, a university relationship has developed which may be different from that which would be developed at a larger integrated Steel Works. This paper outlines the type of cooperative studies carried out by Stelco Inc. in Edmonton and the University of Alberta. .To meet the research needs covering a wide variety of steelmaking processes and steel products produced in Edmonton would require more staff and equipment than the sales volume in the West justifies. The gap is filled by cooperation with university personnel. This cooperation has provided these benefits to Stelco Inc.:• access to specialized test equipment and a trained staff to operate it; and• assistance from experts in the areas of product testing and problem solving.Moreover, the close proximity of the university to the plant allows frequent meetings and ensures that practical solutions are developed and implemented. A good example of the ongoing university I industry relationship developed is the joint work on improving cultivator shanks."

Jan 1, 1982

By C. R. Stelck

"AbstractThe Cardium formation of northeastern British •Columbia •contains an erosional unconformity that becomes progressively more severe northward until, •at Liard river, the stratigraphic hiatus eliminates the underlying Lower •Cardium sandstone, the Kaskapau formation, and the upper Dunvegan sandstones. The area of unconformity roughly coincides with the distribution of the continental facies of the earlier Dunvegan formation. Along Wapiti river, the zone fossil Scaphites ventricosus Meek and Hayden is found in the Bad-heart member of the overlying Wapiabi shale; Scaphites :preventricosus. Cobban marks the base of the Wapiabi shale; Scaphites cf. corvensis •Cobban is found in the middle shale member of the •Cardium formation. The log of the Red-Willow No. 1 well shows close similarity to the outcrop sections south of Wapiti river. The Cardium formation is mainly late Turonian in age. Two other pre-Cardium Turonian sands of north-eastern British Columbia are named the Wartenbe and Tuskoola sands.IntroductionTHE Upper Cretaceous Cardium (Bighorn) sandstone formation of the Foothills of northeastern British Columbia carries within its formational limits an erosional unconformity. The unconformity decreases to the southeast, becoming in immediate shoreline regions, now under the plains, a minor diastem. Such diastems, or stratigraphic intervals of non-deposition, occurring in the shallow unda-zone are paralleled in the deeper portions of the unda-zone by the phenomena of sub-aqueous winnowing. '.This winnowing and re-working •at critical depths creates sand areas with porosity."

Jan 1, 1955

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By M. King Hubbert

"The present large-scale use of energy and power by the human species represents a unique event in the billions of years of geologic history. Furthermore, in magnitude, most of the development has occurred during the present century. In the United States, the peak in the rate of petroleum production occurred in 1970 and that for natural gas is imminent. The peak in the world production of crude oil is expected to occur at about the year 2000 and that for coal production at about 2150 or 2200. For other sources of energy and power, water power, geothermal power and tidal power are inadequate to replace power from fossil fuels. Nuclear power, based on the breeder reactor and utilizing lowgrade deposits of uranium and thorium, has a larger potential than the fossil fuels, but it also constitutes a large perpetual hazard. The largest source of energy available to the earth is solar radiation. This source has a life-expectancy of a geologic time scale, is nonpolluting and is larger in magnitude than any likely requirements by the human s pecies. In consequence of the large supplies of available energy, the period since 1800 has been one of an unprecedented exponential industrial growth. This also has been accompanied by a world-wide ecological disturbance, including that of the human population. It can easily be seen that such a period of growth must be ephemeral in character and, in fact, is now almost over. One aspect of this transition from a state of exponential growth to a state of nongrowth is the present alarm over an ""energy crisis."" Actually, the world's present problems are by no means unmanageable in terms of present biological and technological knowledge. The real crisis confronting us is, therefore, not an energy crisis but a cultural crisis. During the last two centuries, we have evalved what amounts to an exponential- growth culture, with institutions based on the premise of an indefinite continuation of exponential growth. One of the principal consequences of the cessation of exponential growth will be an inevitable revision of some of the tenets of that culture."

Jan 1, 1973

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By J. A. Meech, C. A. Harris

"The application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved and because of problems with accurate on stream measurement of process variables. Conventional control is based on proportional, integral and derivative functions of a continuously measured error term. Computer control can enhance these actions by incorporating logical routines to switch from one relationship to another. The success of this logical approach depends on our understanding of the process dynamics and the stability of the process and model under all conditions. Typically the model does not apply at all times in mineral processing because of frequent and unmeasurable changes in the ore parameters.Recent advances in the theory of fuzzy sets have led to the application of this science to process control. Fuzzy Logic can be used to develop heuristic or rule-of-thumb controllers with the strategy based on the actual operating practice of experienced plant operators. Control action has increased flexibility through the adaptation of human reasoning. Acceptance of the control system by operating personnel is significantly higher because of their participation in its formulation. The requirement of an exact model is not essential.A heuristic controller has been designed and tested with a computer simulation model of a secondary crushing plant. The results of this study are discussed and future applications of this control technique to other mineral processes are suggested. IntroductionThe application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved. Mineral processes typically are characterized by non-linear relationships between input and output variables. Many of these variables cannot be monitored accurately on-stream and so long time lags on the measurement loop are features of the system. The processes, themselves, often have long time-varying responses while the process loads fluctuate significantly on a short-term basis.Attempts to control these processes have led to the formulation of mathematical models to describe each unit activity. Adaptive techniques have also been tried to compensate and account for process changes and vageries. These approaches are mathematically rigorous so that their complexity and precision limit their usefulness when applied to ""vague"" processes."

Jan 1, 1987

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992

By Dale A. Walters

The thermal recovery of bitumen reservoirs by steam assisted gravity drainage (SAGD) is often designed to maximize the operating pressure. In general, the benefits of higher operating pressures are higher steam temperatures that maximize the reduction of oil viscosity, potential permeability enhancement associated with lower effective stress and shear dilation, and a larger pressure window to allow flexible control of the producer. This is especially important for shallow reservoirs where the pressure window for injection and production is smaller. Higher operating pressure can reduce thermal efficiency (due to heat losses), but the other benefits usually compensate. The limitation of the maximum operating pressure is then based on maintaining caprock integrity. Thus, shear and tensile failure mechanisms must be quantified and managed. This paper presents a geomechanical analysis of caprock integrity for SAGD operation. Both analytical and numerical approaches are used to investigate the modes of caprock failure. Main factors in the analysis are the knowledge of the initial stress state and proper representation of the complexity of the geomaterials. Typical initial stress states for northern Alberta are presented showing the potential for low initial minimum total stress and elevated initial shear stress levels. The stress-strain behavior for the sand and caprock materials is discussed focusing on the potential for shear dilation in the sand and shear strength behavior in the caprock. Elasto-plastic constitutive models used to represent the sand and caprock are presented and compared using numerical analysis. The increase in pressure and temperature alter the stress state and disturb the soil matrix. This disturbance results in shear dilation of the sand matrix creating regions of enhanced permeability and porosity. Also, the transfer of stress and strain to the caprock causes dynamic stress changes and, therefore, dynamic behavior of shear and tensile failure conditions. Calculations are presented showing the stress paths associated with SAGD operations, suggesting better design of lab testing programs and the implications for shear dilation in the sand and shear failure in the caprock.

Jun 1, 2012