Search Documents

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

By Meimei Zhang

In the overall open pit mine planning process, mining phase design is a strategic driver in guiding and constructing the block extraction sequence and determining the annual net cash flow distribution. Mining phase design should obey some practical constraints, such as ?minimum mining width? and ?flat mining phase bottom?, to allow space for haul road development and truck and shovel access on each bench. However, these practical mining phase design requirements are not taken into account in all first-cut mining phase design methods and post-processing is always required to convert an impractical design to a practical one, resulting in a potentially significant loss of Net Present Value (NPV) relative to the first-cut impractical designs. In this paper, we present a method using a meta-heuristic algorithm ? Simulated Annealing ? to enforce those practical constraints in determining a mineable phase design whilst ensuring minimum NPV loss.

Oct 1, 2009

By Fridrik J. Kristjansson, Stephen R. Hicock

"Three varieties of till are recognized in the Beardmore-Geraldton area: local lodgement till, nonlocal carbonate till, and local supraglacial till. The local lodgement till unit is examined in detail for the first time in this paper. It is the best potential overburden exploration medium for gold and other metals because its particles were locally-derived and deposited subglacially, probably within a few kilometres downglacier (southwestward) from their sources, and have not been diluted by distantly-derived glacialdebris. Both local tills are richer in gold and other metals, relative to nonlocal carbonate till. Local lodgement till rests on bedrock and was encountered frequently at or near the surface in thin drift/bedrock terrain (a widespread terrain type within the west half of the study area), and commonly at the base of boreholes in thick till terrain.INTRODUCTIONDrift prospecting in areas of glaciated terrain has been well documented (in a variety of journal publications and symposium volumes; e.g . Strobel and Faure 1987; MacDonald and Mills 1988) and has proven valuable especially where overburden thicknesses hinder traditional exploration techniques. Drift prospecting techniques may well prove valuable in the Beardmore Geraldton area. This applies especially to the Wildgoose Lake Turkey Lake area where a thick and laterally extensive sheet of nonlocal carbonate till has impeded conventional mineral exploration programs (Fig. I; note the lack of gold occurrences around Wildgoose Lake).Till in .particular has been cited as the best prospecting medium among the various types of glacial sediment (e.g. Shilts 1984). Three end member till varieties are recognized in the study area: (I) local lodgement till which rests directly on bedrock; (2) non local carbonate till; and (3) local supraglacial till which occurs predominatly within, or just downglacier of, upland areas where it commonly mantles the other till varieties. Previous authors have documented how the non local carbonate till hinders gold exploration (Geddes and Kristjansson 1986; Karrow and Geddes 1987; Kristjansson 1986; Hicock 1986, 1987a, b, 1988; Kristjansson and Thorieifson 1987; Thorleifson and Kristjansson 1987, 1988a, b) and why the local supraglacial till may be a good unit for prospecting (Hicock 1986). One detailed surficial geology map sheet of the area has been published (Kristjansson et al., 1988) and others are in preparation. Closs and Sado (1981) reported on the geochemistry of soils and glacial sediments in the west half of the study area. This paper documents the local lodgement till unit and demonstrates why it is the best overburden unit to use for drift prospecting."

Jan 1, 1989

By R. B. Casault, J. D. Boyd, D. R. Bell

"Full-scale sections of three different types of Grade 483 line pipe have been evaluated extensively. The variations in chemical composition, optical microstructure, tensile properties, hardness and Charpy impact toughness with specimen orientation and location were determined. Significant variations in several properties, notably Charpy shelf energy, impact transition temperature, inclusion content and ferrite grain size, were observed for different locations in the pipes. The results indicate that current specifications call for test samples for the most conservative locations, except for impact tests. Minimum Charpy impact values generally occur at the II2-width location, which may be a more appropriate specified test location than the present I/4-width location. The anisotropy of impact toughness, and the importance of low sulphur content and inclusion shape control for adequate toughness in the transverse/rolling-direction orientation were demonstrated. The orientation of impact specimens is critical for spiral-weld pipe, and the current specification test is non-conservative in that it can give results which are two to three times higher than the minimum value for the steel.IntroductionThis report presents the results of an extensive metallurgical evaluation of three different Grade 483 line-pipe steels. The sample material came from full-scale sections of line pipe, which represented current commercial practice at the time of manufacture (1975-1977). Since then, significant improvements have been made in the manufacturers' procedures for producing skelp and pipe, and the line-pipe specifications have been revised. Hence, the information in this report is dated in terms of current design, but it is unique and significant in several respects:"

Jan 1, 1982

By A. Griffiths, G. Vickell

"INTRODUCTIONA successful cyanide destruction process has to ensure environmental compliance at reasonable cost. That this is possible with hydrogen peroxide is shown by the fact that over twenty gold mines either already use H2O2 or intend to start using it within the next few months. About half of these mines are in Canada.This growth is remarkable, considering that the first treatment plant to use H2O2 for detoxifying cyanide was commissioned less than five years ago at Ok Tedi, in Papua New Guinea.Hydrogen peroxide is being applied to a wide range of situations, including:Treatment of CIP pulps; examples: Ok Tedi, PNG; Hope Brook, Nfld.Treatment of barren bleeds and filtrates; examples: Nickel Plate, B.C.; Puffy Lake, Man.Treatment of tailings pond discharge; examples: Detour Lake, Ont., Page Williams, Ont.Treatment of excess heap leach solution; examples: Hope Brook, Nfld; Gordex, NS.Treatment of barren heaps after heap leaching; examples: Alhambra, NV; Wharf Resources, S.D.Treatment of pond reclaim water to prevent either ""preg-robbing"" or depression of gold-bearing pyrite in a flotation step; example: Getchell, NV.Treatment of backfill to prevent possible groundwater contamination; example Hope Brook, Nfld.Treatment of tailings ponds to prevent bird kills; example: Paradise Peak, NV.""Emergency"" units to deal with unusual events such as freak storms or dam failures."

Jan 1, 1989

By J. B. Morrow

Methods of Coal Preparation Fundamentally, the object of coal preparation is to increase, economically, the value of a fuel by making it more suitable to the uses of the consumer. This can be accomplished in three major ways: 1.Screening or sizing 2.-Mixrng or blending 3.-Cleaning By combinations of any or all of these methods we can prepare coal to meet standard specifications-a process of standardization which is the more desirable the more nearly it approaches the unvarying quality of packaged goods, where the package you buy today and tomorrow is the same as that you bought yesterday. It should be noted that it is readily possible to get good cleaning and still have poor preparation because of faulty screening and mixing, and, on the other hand, it is possible to get a passable grade of cleaning, combined with good screening and mixing facilities.

Jan 1, 1931

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By W. H. Patterson

The history and experience of early companies in the Islands is illustrated by the typical transactions of Trans-Western from 1959 to date. Trans-Western had entered into farmout agreements with companies strong enough to carry out at least the required minimum exploratory work and then such development as might be warranted. The farmee companies were required to make deposits to guarantee work performance during the first period of validity, i.e. the first 3 years of the 12-year life of the permits, and at the rate of 5 cents per acre. At that time, a good deal of geology was available, as a result of extensive exploration that had been carried on by the Geological Survey of Canada and other geological enterprises, with field parties travelling over and camping on all of those Islands. Trans-Western's farmees then selected, from Trans-Western's priority on 13.5 million acres, what they believed were the lands most prospective of producing large oil and gas discoveries, and, having the right to trim off acreage which they considered less prospective, thereby reducing the acreage of Trans-Western and its farmees to in excess of 5.5 million acres. The farmees then commenced a 3-year program carrying out geological exploration to the required minimum of 5 cents per acre, and with some permanent and many mobile camps.

Jan 1, 1969

By M. L. Trépanier

"Engineering and technical services are supplied by the Engineering Department, located at Thetford Mines, Quebec, approximately 60 miles southwest of Quebec City. The department serves the three operating mines in the Thetford area, the Asbestos Hill mine at Putuniq, Nouveau Quebec, and the Nordenham plant at Nordenham, West Germany. The Engineering Department is responsible for supplying the following services. 1. Administration and coordination of capital projects. 2. Engineering, design and drafting services for in-plant changes or improvements. 3. Preparation of geological plans for mine planning and ore reserves determinations. 4. Short-, medium- and long-term mining plans. 5. Rock mechanics studies and monitoring. 6. Grade control monitoring. 7. Environmental control engineering and construction. Details of the organization and services rendered will be the basis of the paper."

Jan 1, 1976

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

By J. R. Giegerich

"IntroductionMINING operators in common with other operators are confronted today with two serious problems, shortage of experienced workmen and rising costs. The following review of practices at the Sullivan mine of The Consolidated Mining and Smelting Company of Canada, Limited, outlines certain measures that have been responsible, during recent years, for minimizing the effect of these two problems. The paper is divided into three main sections:( 1) Training programmes and job studies( 2) Improved mechanization and equipment( 3) Large-scale methods of operationTraining Programmes and Job StudiesJob TrainingJob training courses were introduced at Cominco immediately after the last war and proved to be a great benefit to the operations. There were three courses given, Job Instruction Training, Job Safety Training, and .Job Relations Training. These were spread over a period of two years and were taken by all operating supervisors and some key operators.The courses were introduced by a trained instructor from the British Columbia Department of Labour. This man trained twelve of our employees as instructors by giving them an intensive one-week course. Similarity between the three courses was such that the instructors trained in the first one were very readily trained for instruction in the two succeeding courses."

Jan 1, 1952

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By A. A. Sizikov, V. A. Sizikova

Key parameters to consider for any producer: bring down production cost and lead time; Lean production as a tool to achieve maximum efficiency; How to implement lean principles: discontinuous vs. continuous production (aluminum industry); About RUSAL: global top-three aluminum producer; Lean tools at use at RUSAL's production facilities; Pull system, Standardization of work, Just in time, Continuous improvement, Customer-Supplier relations, etc.

Jan 1, 2006

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By A. Ignatieff

Introduction Some interest is being shown in Canada in underground gasification of coal and, as developments have now taken place in several countries of the world, it is thought that a review of progress, particularly from the viewpoint of a mining engineer, may be of interest. The literature on the subject, and notably that of Russian origin, is already very voluminous. The various methods of underground gasification of coal have evolved from initial attempts to employ underground workings as gasifiers of previously fragmented coal or to use some method that involves little or no preparatory work underground. The 'stream' method, shown schematically in Figure 1, has been the only one used in tests to date in countries outside the U.S.S.R. Other methods, involving preparatory work underground prior to gasification, are the early 'chamber' method, where fragmented coal was gasified in rooms between inlet and outlet entries, and the underground borehole' method, illustrated in Figure 2, where gasification is developed in a succession of boreholes which are temporarily sealed and then abandoned in turn after gasification. The stream method appears. to be particularly suitable for pitching seems as it is claimed that the pitch prevents ash accumulation or serious blockage from roof falls, and it also aids the circulation of the stream. As a considerable proportion of Canadian medium and high-rank coal seams are inclined, it would seem that, at least at the outset, the stream method or a modification thereof would be the one most applicable to all but the Saskatchewan lignite fields and the flat domestic-coal fields of Alberta.

Jan 1, 1949

"A simple approach to optimizing the performance of an operating carbon in pulp (CIP) or carbon in leach (CIL) plant is presented. It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch tests in which the rates of gold leaching and carbon adsorption are determined, coupled with mathematical models that translate the batch kinetic data into predicted steady state profiles of gold in solution and on the carbon across multi-stage adsorption circuits.Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the stepwise change can be determined. In this way it is possible to inexpensively optimize the design of both greenfields CIP or CIL circuits and plant expansions, or optimize the operating parameters of an existing plant, with no disruption to plant operations and no economic risk to the mining company.This approach has been adopted by IAMGOLD Corporation, to the immediate benefit of two of their existing gold operations. The methodology adopted and the results achieved are presented.INTRODUCTIONThe carbon in pulp (CIP) and carbon in leach (CIL) processes became firmly established in the gold mining industry in the 1980s, initially in South Africa and Australia, from where they spread rapidly to all the gold producing regions of the world. The percentage of annual global gold production by activated carbon-based processes grew from zero in the 1970s to almost 70% by the turn of the century, which represented a phenomenal rate of acceptance of a new technology by a traditionally conservative industry. The main reason for this rapid acceptance of the new technology was the fact that the first few large plants built in South Africa convincingly demonstrated better gold recoveries than the traditional filtration/Merrill Crowe process, with lower capital and operating costs. And as the plants developed an operating track record over their first few years of life, they proved to be remarkably robust mechanically, and highly tolerant of plant upsets, changes in feed composition and solution phase contaminants that had caused problems in Merrill Crowe plants."

Jan 1, 2011

"THE GOLD MINING REGION of Timmins - Val d'Or, astride the Ontario-Quebec border, has long suffered the effects of rising costs during the period when the U.S. price of gold was fixed at $35 per ounce. The federal government, through such assistance programs as that set up under the Emergency Gold Mining Assistance Act (E.G.M.A. ) in 1948, has subsidized the gold mining communities of Canada for a total of over $300 million to March 31, 1972. Of this, the Timmins - Val d'Or ""gold belt"" has received more than twothirds, almost $220 million. In spite of these continuous subsidies, only 12 gold mines are still producing in the Timmins - Val d'Or belt, whereas 71 mines have received subsidies for some period since 1948. The vital question is how the communities previously supported principally by the mining of gold will survive in the long run, as many of the older mines either are already depleted or are quickly becoming so. With the rising price of gold on the 'free market in recent months, prospects look a little brighter for the time being. Even with the increased official price of U.S. $38, which made the maximum government subsidized price about $48 per ounce, gold mines have not sold any gold to the government since January 1972 and some stopped doing so months before that. The populace of the region has not been enthusiastic about relocation nor about extensive retraining programs in the past and probably will not be in the future. So, when the remaining gold mines become depleted, the old problems of community depression will remain."

Jan 1, 1973

By A. R. Kinkel JR.

"The Buffalo Ankerite mine is in the southern part of the Porcupine gold district of northern Ontario. The mine has a history of exploration and development reaching back to 1911, and has been operated continuously since 1932. From 1932 to 1942 a total of 510,874 oz. gold was produced from the mine. In 1941 the production was 71,654 oz. from 448,621 tons of ore.With few exceptions, the ore-bearing veins did not crop out. They were discovered during the prospecting of the prominent outcrops of barren or low-grade quartz-carbonate breccia near the veins.GEOLOGICAL SETTINGThe Porcupine gold district lies in an area of folded and sheared Precambrian lavas, sediments, and intrusives. The Buffalo Ankerite mine is in the southern part of a large fold. The structure appears to be a continuation of the Vipond cross anticline and accompanying syncline described in earlier papers (1, 2). The orebodies lie along both flanks of the synclinal part of the fold, and are known as the north and south vein systems, respectively. No mineable veins have been found on the axis of the syncline (Fig. 1).The rocks found in the mine area are pillow lava, dacite, conglomerate, quartz porphyry, tuff, and fragmental lava. The tuff and fragmental lava are now largely altered to chlorite schist. Productive veins have been found only in pillow lava, dacite, and conglomerate, but a minor amount of gold occurs in some of the quartz porphyry. The Porcupine Creek fault, a zone of intense shearing over 1,000 feet in width, lies immediately south of the mine. A spur fault branches to the northwest from the Porcupine Creek fault, separating the north from the south vein systems ( Fig. 1) ."

Jan 1, 1954