Search Documents

By R. A. Ozerkevich, R. J. Voisey

"SherrGold's MacLellan V ne is located about five miles south east of Lynn Lake immediately to the east of the Keewatin River. (Figure # 1)The property is accessible by an all weather road, leading north from the provincial highway 391, which links Lynn Lake with the Town of. Leaf Rapids and the city of Thompson to the south.The MacLellan Mine (formerly the Agassiz property) was discovered in the early 1950's and optioned from Comiesa Corporation in 1979 by Sherritt. SherrGold Inc. was formed in September 1985. Sherritt then transferred the MacLellan Mine, 15 other gold prospects in the Lynn Lake area and the old Lynn Lake nickel-copper mill to SherrGold. At the same time Sherrgold entered into a management agreement with Sherritt whereby Sherritt would develop and operate the MacLellan Mine and conduct SherrGold's exploration activities.The ore body as outlined in the original feasibility study is expected to produce in excess of 300,000 ounces of gold and 450,000 ounces of silver over the next 5 years. However the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 30 miles west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan mine or relocated to Sherritt's Ruttan Operation."

Jan 1, 1987

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By I. I. Inculet, M. A. Bergougnou, J. D. Brown, R. M. Quigley, D. K. Faurschou

"Coal from Hat Creek, B. C., has been successfully beneficiated to remove ash while retaining calorific value by a dry electrostatic separation process using a fluidized bed for triboelectrification. Two samples of Hat Creek coal used in the beneficiation experiments have been characterized particularly with respect to their mineral and clay content. The calorific value recovery exceeds the simple dry coal recovery because of the heat lost in altering the clay minerals of the ash fraction during burning. Recoveries and ash contents of the beneficiated coal are comparable to recoveries by water washing, but the dry process avoids the potential water pollution problems.IntroductionProposals have been made which suggest an interim Canadian coal production target for the end of the century which will require a four- to fivefold increase over the 1977 production. This implies a nominal annual growth rate of about 6070 to achieve a production rate of 115 to 140 million tonnes/year. Whether or not this target is realistic, it is becoming increasingly evident that coal must be utilized more fully on a world-wide basis. The crisis in Iran has provided the latest stimulus to renewed interest in Canadian coals for domestic use and export.The emerging new era of coal utilization for fuel and chemical feedstock will not, however, generally tolerate the level of coal technology which prevailed prior to the availability of abundant cheap oil and natural gas. Economic, environmental and resource management considerations will necessitate, for example, the use of improved methods of beneficiating coal. Continued development and application of conventional processes, principally aqueous, involving heavy media and cyclones will solve many of the problems. However, less conventional processes may be preferable or necessary in certain applications."

Jan 1, 1980

By J. Y. Hascoet, M. Marya, S. Marya

Additive manufacturing (AM) brings disruptive changes over the ways parts and products are designed, tested, qualified, assembled, inspected and marketed. With these changes come real technical challenges, therefore, concerns that mainly stem from the maturity and diversity of today’s AM processes, the feedstock materials, and the interactions between the numerous process parameters. Additive manufacturing is somewhat similar to laser and electron-beam conduction-mode welding and involves a multitude of dynamic physical events between projected feedstock and moving heat source that influence process robustness, thus deposit properties. For this paper, a simple air vent, selected for its size, thin-wall, hollow geometry and materials (specifically 316L) was made using a laser-based powder blown technology (Construction Laser Additive Direct or CLAD) and systematically inspected by optical microscopy, microhardness indentations, and electron-back-scattering diffraction (EBSD). This exemplary part is first analyzed to broadly discuss metallurgical phenomena in additive manufacturing, particularly solidification and texture development. The paper then expands to other alloys and continues correlating metallurgical observations to process parameters and part properties, also borrowing from past experience with the same 3D printing CLAD system.

Jan 1, 2014

By Michael J. Rosko

Methods have been developed for processing and analyzing reflected solar radiation data obtained by Landsat 5 Thematic Mapper multispectral scanner. Spatial resolution for the Landsat series satellites is 30 meters per side per pixel. Materials on the Earth?s surface absorb or reflect different parts of the electromagnetic spectrum depending on their physical and chemical properties and, therefore, typically have characteristic spectral ?signatures?. Using these signatures, environmental parameters such as surface water and vegetation may be identified and analyzed. Principal advantages of the satellite image method for environmental monitoring include: a relatively long historic period beginning in 1985 for which information is available, the reliable numerical basis for the results, and the ability to assemble a historic environmental baseline and provide on-going monitoring for large or remote areas where standard monitoring methods may not be practical. However, because the long-term continued operation of Landsat 5 is problematic due to the age of the equipment, QuickBird and IKONOS satellite images were processed to determine if the two systems are sufficiently similar in their results to allow continuing monitoring using QuickBird data. The QuickBird satellite was launched in 2001 and collects the same visible and near infrared spectral bandwidths as Landsat 5, allowing for equivalent process algorithms for QuickBird, IKONOS, and Landsat 5 data. Spatial resolution for the QuickBird images is 2.4 meter per side, allowing for more detailed characterization of the land surface; spatial resolution for the IKONOS images is 4 meter per side. Because of several differences between the satellite systems, including degradation of the Landsat 5 sensor, it is necessary to calibrate QuickBird and IKONOS results to the Landsat results to verify similarity. Recent images from the satellite systems have been processed and results have been compared to determine the validity of comparing Landsat 5 and QuickBird/IKONOS images so that these newer data can be used reliably in the future instead of Landsat 5 data. Results from this comparison are presented in this paper and suggest that analyses for vegetation using the two satellite systems are comparable, and that little calibration is required. Results from comparison of surface water results from the two systems are less comparable and is currently being investigated by the authors.

Oct 1, 2009

By G. J. Hawkes

"We all know that every man who works for us should have a thorough knowledge and understanding of his responsibilities. But how about ourselves? Du we have a thorough knowledge and understanding of our own responsibilities as Mill Superintendents?I once had an occasion to say to a Manager that I did not know something was my responsibility and he replied with suitable emphasis ""Everything inside those four walls is your responsibility"". That makes the extent of our responsibilities clear but does not give us a check list to keep an eye on as we do our job from day to day.What are our responsibilities? I suggest they are the following:1. Developing and maintaining efficient operating and maintenance crews.2. Milling the required tonnage.3. Recovering the economical maximum amount of gold.4. Keeping costs at the economical minimum.5. Seeing that the figures are reasonably accurate for tonnages, assays, production, losses, and costs.6. Preventing accidents.7. Preventing fires.8. Maintaining the equipment and building and keeping them clean and tidy.9. Enforcing company rules and regulations."

Jan 1, 1965

By K. R. Coulter

"Good morning gentlemen. I am very pleased to have this opportunity to tell you a few of the things that happen within a completely unrelated activity, the electroplating industry, except that it does consume metals and has some slight similarity of problems so far as cyanide is concerned.First, just a few general terms about the industry. It is a relatively unsophisticated industry technically, and in many instances there are serious problems in obtaining staff that can operate the various systems that are currently available for destroying cyanide or precipitating metals.I would suggest to you that if you are investigating any system that you consider very seriously the personnel that are actually going to run it. The installation people; probably have some idea what it is all about but the operators must be chosen for their ability and not because they just happen to be available.We perhaps have another area in common. There is very little money for capital expenditures that produce no immediate return or even eventual return on the investment.The industry is largely made up of ""Jobbers"" who are strictly electroplating. There is another group in which the electroplating is captive as in large companions where it is a convenience operation. Also there are specialists, who do other things besides plating but it is a very major part of their operation. This applies to the automotive parts industry.Cyanide applications in the plating industry will be for copper, zinc, cadmium, silver, brass, and gold. Cyanide waste solutions come from those solutions adhering to the plated parts, and from the occasional discharge of the plating bath solutions. Also, in a related industry, the heat treating people with cyanide case hardening have some high concentrations of cyanide to dispose of. Concentrations of cyanide that we treat are 2500 parts per million or higher especially in wastes from heat treating. Solution volumes might be as low as 100 gallons per hour in a well run, carefully operated rinsing system. It may be as high as 3000 gallons per hour where dilution occurs."

Jan 1, 1973

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By John Postle, Maureen Jensen, Marcel Vallee, Bernie Haystead, Dan Hora, Graham Clow

The Committee's proposed standards establish definitions and guidelines for the reporting of Exploration Information, Mineral Resources and Mineral Reserves in Canada and are identified as the "CIM Standards" and referred to as such hereafter in this document. To provide additional clarification to Qualified Persons (QPs), guidelines have been included with the respective definitions. The CIM Standards are applicable to all minerals including industrial minerals, diamonds and other gemstones. Reserve definitions for bitumen, natural gas and oil are not included in these Standards. The CIM Standards are not intended to cover mineral inventory estimates that will be reported to government agencies.

Jan 1, 2001

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By R. Harrisson, K. Esmaieli

Brunswick mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance of ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions, etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Jan 1, 2008

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017

By H. W. Wevers

This paper is the result of an intensive literature search and practical study of the problems experienced by a mining company with the frame cracking of their large-tonnage haulage trucks. It explains the advantages of particular HSLA steels for applications in the welded structures of such equipment. Examples of existing welds in truck frames are analyzed. Modern fatigue models and linear elastic fracture mechanics techniques are explained.

Jan 1, 1978

By B. Benmokrane, G. Ballivy

"RésuméLe mécanisme de transfert des charges et le processus de décohésion le long des scellements d'ancrages scelles dans des massifs rocheux sous des charges de tensionnement peut être examine par instrumentation de l'ancrage à l'aide de jauges de déformation. Dans ce contexte il est présente ici les résultats d'une étude, en vraie grandeur sur chantier, ayant porte, d'une part sur des essais d'arrachement conventionnels et d'autre part sur des essais déflagrée barres d'ancrages instrumentées et scellées à l'aide d'un coulis de ciment dans un massif rocheux sain et compètent. Les résultats décrits ici, particulièrement les profits de contraintes de cisaillement le long de l'ancrage, obtenus à partir des valeurs de déformations relevées sur les jauges, ont permis de préciser le niveau de chargement correspondant à la décohésion initiale du coulis de scellement, d 'examiner l'effet de la décohésion sur la distribution des contraintes et de caractériser le fluage du système barre d'ancrage/coulis de scellement.ABSTRACTThe load transfer mechanism and the debonding process along grouted rock anchor, subjected to tention loads, can be examined through the instrumentation of the anchor with the aid of strain gauges. In this context, the resultsof a full-scale site investigation including classical pull out tests and creep tests are presented in this paper. These tests were performed on instrumented bars which were cement grouted in a competent rock mass. Results presented in this paper concern, among others, shear stress pro/ties along the grouted anchors which were determined from strain values obtained from the strain gauges. These results have been used to: (1) predict the load level corresponding to initial debonding of the grout; (2) study the effect of debonding on shearstress distribution along the anchor; and (3) characterize the creep behavior of the bar anchor/cement grout system."

Jan 1, 1991

PRESENTATION PURPOSE ? Provide an overview of BC?s Environmental Assessment Actand environmental assessment process ? Identify key issues influencing environmental assessments in BC ENVIRONMENTAL ASSESSMENT ACT ? Major project proposals require an EA before a project can proceed ? Considers potential effects of proposed projects and ways to minimize or avoid adverse effects Minister of Environment and the Minister designated as responsible for project category decide whether or not to certify a project or order further assessment

May 1, 2006