Search Documents

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By H. E. Miard

"IntroductionIT HAS BEEN SAID, with good reason, that the future of the coal mining industry, in our mountainous regions at least, depends on ability to extend operations successfully to depths greater than those reached until now. However, at many points, Nature has given definite hints that trespassing there could be fraught with very un-pleasant possibilities, unless the intruder be governed by a series of rigidly observed principles. In the coal mines of British Columbia, so far, bumps have taken place only at the Coal Creek colliery, but there they gave ample evidence of the extent to which they can hamper underground operations. Some of these manifestations have also been experienced at the McGillivray Creek colliery, in Alberta, at Carbonado, in Washington, and at Sunnyside, in Utah.Cognate phenomena, known as 'air blasts', have been experienced also in some deep metalliferous mines in British Columbia. Such occurrences were responsible for three fatal accidents at the Le Roi and War Eagle mines, near Rossland, in 1916 and 1917.In more or less disturbed coal fields, another form of stress release, equally detrimental, has been still more generally experienced than have been the bumps. Coal outbursts have taken place at Morrissey and Coal Creek, in the Crow's Nest Pass district, and at Cassidy, South Wellington, and the Nanaimo Reserve colliery, on Vancouver island. Manifestations of this kind have been made the subject of intensive study in European countries where they occurred on a really impressive scale, which must not be construed as meaning that some of our own outbursts did not approach a comparable magnitude."

Jan 1, 1953

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By M D. Winning

The historical development of the elemental sulphur recovery industry in Western Canada is reviewed for the period 1952 to 1965. A brief technical description of a typical modified Claus sulphur recovery unit is presented. Some predictions are made concerning the future of the elemental sulphur recovery industry in Western Canada. THERE are evidences of sulphur or its compounds having been used for religious and medicinal purposes as far back as we have a recorded knowledge of history. As typical examples, sulphur was burned as a sort of inverse incense to drive away evil spirits at religious festivals, sulphur ointments were used by the early Egyptians to cure eye ailments, and hot sulphur-spring water was used as a cure for a variety of ailments. Thermopyle was called "Hot Gates" be-cause of its fame as a spa as well as a mountain pass. The Romans discovered the sulphur deposits in Sicily and mixed sulphur with bitumen for incendiaries; and, of course, anyone familiar with the travels of Marco Polo knows about the Chinese development of gunpowder, which contains sulphur. In some aspects things haven't changed much today. We still use sulphur-bearing ointments, and we still use the hot sulphur springs such as the one at Banff in Western

Jan 1, 1965

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013

By Mike D. Riley, Alan V. Bell, Ernest K. Yanful

Acid mine drainage (AMD) research under the MEND program has been ongoing since 1988 at the Heath Steele Mines waste rock piles including sulphide material, outside Newcastle, NB. In 1989 approximately 10,000 mt of waste rock was placed on a prepared sand base with an underlying impermeable membrane. The waste rock pile was heavily instrumented for measuring oxygen concentrations and temperatures. In September 1991, a composite soil cover designed for the Heath Steele climatic conditions, using local soils, was placed over the pile, creating a totally enclosed system. Moisture content and oxygen probes were installed within the composite soil cover to monitor changes within the soils over time, while two large-size lysimeters were installed below the cover to monitor the hydraulic conductivity of the cover. The waste rock site has been monitored on a monthly basis since installation of the cover, for performance of both cover and waste rock. The monitoring shows very clearly that the placement of the composite soil cover has had a major impact on the generation of AMD. Major reductions in temperature and oxygen concentrations within the waste rock pile indicate that the cover has significantly inhibited the oxidation reaction that generates the AMD. Performance data have shown that the cover has maintained its integrity under the climatic conditions of the area.

Jan 1, 1995

By M. P. Filion, K. Ferguson, L. L. Sirois

Acidic drainage is the largest single environmental problem facing the Canadian mining industry today. Technologies to prevent acidic drainage from occurring in wasterock piles and tailings sites, and on the walls of open pits and underground mines, need to be developed and demonstrated. There are two groups in Canada which have accepted this challenge: the national Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Mine Drainage (BCAMD) Task Force. This paper summarizes the activities of these two organizations.

Jan 1, 1990

By A. G. Ballachey

Introduction This paper will describe the mining plant and underground operations at Quemont. Details of geology and milling are beyond its scope. Papers on these subjects will be prepared and presented separately. A detailed account of the exploration and development, 1944 to 1947, has been given by W. L. Brown (1). Location The mining concessions of Quemont Mining Corporation, Limited, are in Rouyn township, Rouyn-Noranda county, northwestern Quebec. These concessions total about 640 acres in area. They lie within the limits of the City of Noranda, contiguous to, and directly north of, the Horne mine of Noranda Mines, Limited. A large area in the southern part of the property is covered by the north arm of Osisko lake. Production The present operating rate is about 2,100 tons per day. Three flotation concentrates are produced: copper, containing a large proportion of the gold and silver in the ore; zinc; and pyrite, which carries an appreciable additional proportion of gold. The copper and zinc concentrates are shipped to smelters as produced. The pyrite concentrate is cyanided to recover additional gold, after which it is filtered, dried, and shipped for the manufacture of sulphuric acid. The principal revenue metals are copper, gold, and zinc. Silver and pyrite are important by-products.

Jan 1, 1952

By J. C. O'Rourke

"This paper presents an overview of Alberta Oil Sands Technology Research Authority's in situ oil sands recovery project at its underground test facility near Fort McMurray. It covers the rationale for horizontal wells drilled from tunnels below the oil sands, the tunnel layout, the drilling program, and the recovery process and facilities. INTRODUCTIONThe Alberta Oil Sands Technology and Research Authority (AOSTRA) has constructed an Underground Test Facility (UTF) in the Athabasca oil sands deposit in northern Alberta, approximately 50 km northwest of Fort McMurray (Fig. 1). The facility initially is to serve as an underground laboratory from which to field test new approaches to in situ recovery of the bitumen (oil) in the Athabasca deposit.The UTF employs mine access to get at the effective exploitation of an oil reservoir. It does so, however, under conditions considerably more difficult than those faced by most other applications of the technology. Because of the unconsolidated nature of the McMurray formation, the development of drilling chambers directly in the reservoir would be prohibitively expensive. Further, mobilization of the extremely viscous bitumen requires intensive steam stimulation with the attendant concerns of large, complex well completions and potentially hazardous operations Over-all, the oil sands presents mining, drilling and operations challenges which push the technology to a new state-of-the-art. The UTF as it now exists consists of:• a 20 000 ha lease with all-weather road access;• 925 m of 5 m by 4 m tunnels in the limestone 15 m below the oil sands at roof depth of 178 m below the surface (Fig. 2);• two 3 m diameter steel lined shafts to a depth of 213 m;• administration and sur face mine support facilities from which to operate the UTF (Figs. 3 and 4);• underground piping systems to transport drill fluids, steam, produced fluids and services to and from the future well heads underground (Fig. 5);• surface steam generation and production handling facilities (Figs . 3 and 4).• a drilling rig and auxiliary systems specifically designed to drill long horizontal wells into the oil sands from tunnels in the underlying limestone (Fig. 6);• an experienced staff to engineer and operate the facility (Fig. 7)"

Jan 1, 1989

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

Session 1 ? Intro to MiHR ? Business Case for Aboriginal Inclusion ? Overview of the Mining HR Guide for Aboriginal Communities ? Two presentations of Programs featured in the Guide ?? The RAP Program from NWCC ?? First Nations Youth Employment Program PDAC-MM Session 2 ? Presentation from MAC ? Taking up the AFN Corporate Challenge ? Presentation on Mastering Aboriginal Inclusion in Mining About MiHR Who we are: ? National Sector Council for the Minerals and Metals Sector ? 18-person Board of Directors ? 100+ Industry Leaders volunteer on our project committees ? PPP - Funded by HRSDC and industry What we do: ? Identify national HR challenges and opportunities for the minerals and metals industry ? Create national solutions through collaboration, partnerships and Synergy

May 1, 2009

By P. L. Richard

An open pit a mine can be thought of as a business unit, with capital, operating and maintenance costs that exceed those of many large business enterprises. Truck-and-shovel operations have an inherent ?looseness? to them, unlike manufacturing or processing operations where production components are tightly coupled (through conveyors, material flow in pipes, assembly lines, and so on). Effective monitoring and control of truck-and-shovel operations requires a combination of both information systems and performance management. Production monitoring systems can impact operations at three levels: minute-by-minute decisions during the shift, procedures, and policies. The technology of production monitoring ranges from real-time data collection to manual entry of time card data into a computer. Time card information is too coarse to effectively manage a multi-million dollar fleet of mobile equipment, so a higher level of production monitoring is required. People issues affect whether the implementation will be a success or a disappointment. Considerations that affect the people issues are discussed, including common obstacles, and key success factors. A balanced scorecard approach must be used, since uni-dimensional measures of performance like tons produced give no indication of whether the production was achieved at the expense of another factor.

May 1, 2004

By P. L. Richard

An open pit a mine can be thought of as a business unit, with capital, operating and maintenance costs that exceed those of many large business enterprises. Truck-and-shovel operations have an inherent “looseness” to them, unlike manufacturing or processing operations where production components are tightly coupled (through conveyors, material flow in pipes, assembly lines, and so on). Effective monitoring and control of truck-and-shovel operations requires a combination of both information systems and performance management. Production monitoring systems can impact operations at three levels: minute-byminute decisions during the shift, procedures, and policies. The technology of production monitoring ranges from real-time data collection to manual entry of time card data into a computer. Time card information is too coarse to effectively manage a multi-million dollar fleet of mobile equipment, so a higher level of production monitoring is required. People issues affect whether the implementation will be a success or a disappointment. Considerations that affect the people issues are discussed, including common obstacles, and key success factors. A balanced scorecard approach must be used, since uni-dimensional measures of performance like tons produced give no indication of whether the production was achieved at the expense of another factor.

Jan 1, 2004

By M. P. Kat, R. J. Barclay

"In 1984, a provincial inquiry into ground control and emergency preparedness in Ontario mines was commissioned by the Minister of Labour for Ontario. One of the recommendations put forth by the committee conducting this inquiry was that the Ontario mining regulations be modified to address more effectively the assessment of mine design. Mining regulations now require that every mine in the province annually assess its design with respect to ground stability. Subsequently, the Ministry of Labour has embarked on a ground control audit program to gather as much information as possible about the ground control programs in place at Ontario mines. In 1988, 47 underground mines were audited. The audits are intended to provide an overview of the level of engineering effort that is devoted to ground control on a provincial basis, by identifying the type of geotechnical information that is collected by each mine and how this information is used for stability analysis purposes in rationalizing excavation and support system designs. Also, the audits serve as an indicator of the severity of ground stability problems at individual mines, and how these problems are dealt with.This paper consists of information that has been extracted from the first series of ground control audits that were conducted in 1988. Specifically, the paper describes the types of support systems that are used in Ontario mines. It also discusses the rationale for local ground support selection, and the quality control programs that are in place for assessing the performance of installed ground support. As well, the type of geotechnical information that is collected, and to what extent it is used for the purpose of designing ground support systems, is reviewed"

Jan 1, 1991

By W. Rostoker

Packing Experiments The porosity and most of the other physical properties of a coherent mass of any material built up by the packing together of discrete particles will obviously vary with, and be governed by, the manner of association of the particles. The relation of packing to powder metallurgy has been discussed in some detail by at least two authors. Packing Theory Theories of particle packing have been put forward by C. C. Furnas and A. E. R. Westman. Although their approach to the problem is not the same, their conclusions are similar. In the process of packing, they visualize the voids of a uniformly sized material becoming filled with particles of a smaller size, and the voids between these being filled in turn with still finer particles. Obviously, if this process is carried ad infinitum, the resultant mass will have the same density as the constituent particles. In practice, of course, such a density of packing is never attained. In addition, the premise is made that successive particle sizes must fit into the voids left by the immediately larger particles- an assumption requiring definite size gradations and also particle shapes. It remained, then, for theory to correlate relative diameter ratios, and proportions and numbers of sizes of particles, for requisite packed densities. Briefly, the following principles were postulated: (a) For an infinite diameter ratio between largest and smallest sizes, an infinite number of particle sizes in proper proportion is required to give natural density. (b) For a given diameter ratio, there is a maximum number of permissible particle sizes for maximum packed density (Furnas). (c) Provided the particle shape is spherical, or approximately so, the proportions o particle sizes can be calculated. (d) The ratios of successive diameters of particles are in geometric progression.

Jan 1, 1947

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013