Search Documents

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By J. Forster, C. A. Pickles, Mackowiak. K.

The future development of nickel laterite deposits is crucial with regards to satisfying impending nickel demands. The commercial implementation of new hydro/pyrometallurgical processes in recent years has led to significant improvements in the extraction of nickel from the laterite ores. One potential alternative pyrometallurgical processing route would be to selectively reduce the nickel and produce a concentrate with nickel contents similar to those attainable in the conventional flotation of sulphide ores. However, even bench scale studies have not yet been able to produce a high grade (>15% nickel) concentrate from a low grade laterite ore. The present research involved the microwave vacuum reduction roasting of a nickel laterite ore to yield a high grade concentrate, rich in nickel. Firstly, the effects of temperature and pressure on the nickel grade and recovery were investigated using a thermodynamic model. Secondly, briquettes containing a mixture of charcoal and a low grade silicate nickel laterite ore were reacted in a microwave vacuum system. The experimental variables studied were the input microwave energy, pressure and absorbed microwave power. Thirdly, the ferronickel in the reacted briquette was concentrated by magnetic separation and nickel grades of up to 21% could be achieved.

Jan 1, 2015

By James G. Lyons

All machines vibrate and make noise. An increase signals impending trouble. Vibration and noise analysis allows the condition of the machine to be determined without costly interruption in service for disassembly and physical inspection.

Jan 1, 1977

By Anton Gronningsater

MR. J. R. GORDON: The authors are to be congratulated for their excellent papers on Copper-Nickel Matte Converting. Mr. Drummond's paper contains the results of a thorough and exhaustive study of a series of converter charges. Mr. Gronningsater has presented convincing arguments in favour of his claim that the converter has been neglected as a smelting machine for ore. Some of us may not be inclined to agree with his conclusions. Converting, like most metallurgical operations, is a compromise between an ideal and a practical operation. If it were possible for one to neglect entirely the matter of converter linings, I believe we would all agree that the proper flux for matte in a converter would be pure quartz. Under such ideal conditions, one would, if proper temperature were maintained, make the smallest quantity of slag containing a minimum of magnetite. Converter slags are notorious for their high metal content and must always be subjected to a further cleaning treatment before being discarded. For that reason, the tonnage of converter slag produced should be minimized. If norite is used as a converter flux, then the tonnage of converter slag would be greatly increased if the silica content is maintained at 27 per cent or higher. I cannot agree with Mr. Gronningsater's suggestion that, in con¬sidering a converter flux, the sum of the silica, alumina, alkaline-earths, and alkalis should be considered as being of value. The alkalis and alkaline-earth contents of the flux will replace iron in the silicates formed and tend to increase the viscosity of the slags. However, if the converter is to be used as a smelting machine, it will be necessary to drop the silica content of the converter slag in order to avoid production of excessive slag tonnages.

Jan 1, 1942

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

By Dolea Gabriel Gheorghe

In the present paperwork is proposed an economical-mathematical model (fuzzy) that aims optimize the technological variants of the mechanized coal face. By fuzzification, the issues to solve become more flexible and allow the decision maker to acquire more variants for the functions objectively established. The description of technological solutions is carried out by a set of controllable variables of "category" type by which the type of the machinery is defined within the frame of the actual geological & mining conditions. In the paperwork are used concepts of "successions graph" and "matrix of compatibilities"; with their help a methodology to choose between different technological variants of coalfaces is proposed. It treats the problem of developing the functions that express the membership degree in vague concept. In the end it is presented an assessment procedure for the technological variants of mechanized coal face.

Oct 1, 2009

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Paul Guliov

Coal-bearing Tertiary sediments of the Ravenscrag Formation in southern Saskatchewan host numerous deposits of clinker resulting from in situ coal combustion. Clinker deposits form when sediments of relatively low temperature firing properties overlie coal seams which are undergoing prolonged spontaneous combustion. The resulting fired material is useful for decorative landscaping aggregate, rock gardens, driveways, mud control and others. Predicting the occurrence of clinker deposits requires a knowledge of the spatial distribution of coal seams and the nature ofoverlying sediments. Knowledge ofpaleotopography at the time of coal combustion can assist in locating more highly-fused material which can yield greater block sizes. Coal data bases can be used as a predictive tool by outlining areas where coal is or was at or near surface and therefore may have been susceptible to spontaneous combustion.

Jan 1, 2001

By David Davidson

Overview- Points To Be Addressed ? Review the building blocks of a successful and vibrant industrial economy ? China?s current position in the global economy ? China?s voracious appetite for raw materials ? Distortion in import/export trends ? Areas of strategic importance for China - Steel and its components - Agriculture self sufficiency - Energy now and for the future ? Do current valuation techniques fairly value ?strategic? assets? China ? The Economical Miracle - Massive shift in population from rural to urban - ?Middle class? growing rapidly, hence strong consumer growth - China is the manufacturing center for the world ? cheap labour and - modern facilities - Infrastructure build out ?US$585b stimulus package and 5 year plan - Rail ? 30,000 kms of new track planned by 2020 - Power ? 50% capacity increase, including 35 nuclear reactors - 100 major new airports - State of the art process and manufacturing facilities - Port capacity ? 100m TEU capacity increase by 2020 Class 1 national highway ? 35,000 km?s by 2020

May 1, 2010

By A. J. Makoka, B. C. Qi

Reliable monitoring of corrosion is vitally important in the combat against corrosion and over the last two decades the interpretation of electrochemical noise has received considerable attention as a means to discriminate between different types of corrosion. To this end, many different analytical methods have been proposed, such as power spectral density analysis and analysis via various other stochastic criteria. However, although many corrosion systems are nonlinear and therefore not readily interpretable by the abovementioned analytical approaches, few studies in the analysis of electrochemical noise to date have exploited advances made in the analysis of nonlinear systems. In this paper, the use of phase space methods to analyze and detect change in corrosion systems via electrochemical noise is considered. In particular, the electrochemical noise data are used to reconstruct trajectories in the so-called phase space of the system and changes in the topology of these trajectories or attractors as represented by correlation dimension curves are consequently interpreted as an indication of change in the dynamics of the system.

Jan 1, 2005

By Nadarajah Nanthananthan

Mine backfill has been widely used as a means of ground support. While proper design of backfill is important to ensure ground stability, understanding the failure mechanism and the various influencing factors in a filled block is essential. This paper presents a modified sliding failure model of a confined backfill block. The model considers both the gravity load of the backfill itself and the overlying load from fragmented ore or backfill on the top. A series of new equations were derived and the relationships between factors such as factor of safety, friction angle, cohesion and the exposed stope height were developed. This modified model will be a very useful tool in backfill design, for example, to optimize the design of backfill for a given stope geometry or to determine the maximum backfill height for a particular type of backfill.

May 1, 2007

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By David A. Orava, Richard C. Swider

"The technical knowledge and practical experience accumulated by industry and others in abating acid mine drainage (AMD) is being proactively applied at every phase of the mine life cycle. This paper traces the mine life cycle from exploration to post closure monitoring and maintenance, and reviews AMD abatement measures that have become an integral component of exploration and mining activities.Attention is increasingly being given to evaluating AMD potential as part of exploration work, and studies related to project feasibility and design. Mining, mineral processing, and waste management options are selected taking into consideration their suitability to inhibit AMD. These inhibition measures are typically committed to in closure plans submit-ted at the permitting stage. Mines are operated and decommissioned, often progressively, as planned and in accordance with environ-mental protection policies."

Jan 1, 1996

By Hassan Ghaffari

? HPGR Process/Overview ? HPGR vs. SAG ? The Manufacturers ? Mine Operations using HPGR ? Projects by Wardrop/Tetra Tech ? Economic Benefits ? Questions Main Operating Parameters ? Press Force (N/mm2) ? Roll Speed (m/s) ? Moisture Content (%) ? Feed Particle Size Distribution Specific throughput M* = throughput/D*L*V (ts/hm3) Flake thickness/strength in balance with the compressing force (floating roll situation)

Aug 1, 2013

By S. Torres, J. Álvarez, R. Castillo, R. Fuentes, C. Sandoval, R. Parra, Myakalwar A. K., M. Velázquez, J. Yáñez, D. Sbarbaro

Rapid analytical assessment in copper mining industry is a limiting factor for operational purposes and for the improvement of processes. The present work aims to review the analytical assessment in the copper industry utilizing emerging spectrochemical techniques such as laser induced breakdown spectroscopy (LIBS) and UV-Vis-IR Hyperspectral Sensing. LIBS is a plasma based spectroscopic method where the sample surface is irradiated by high power laser. The light emitted from the plasma contains atomic -molecular spectral information and can be detected using a simple CCD based spectrometer. UV-Vis-IR Hyperspectral Sensing is produced by the reflection of light from the sample’s rough surface in all directions and it can be collected by using an ellipsoid or paraboloid mirror arrangement. The electromagnetic radiation emitted by the samples in the UV-Vis, NIR and MIR region can be used for molecular characterization. The spectrometer splits different wavelengths through a CCD arrangement in 2D spatial and spectral dimensions, thus a hyperspectral cube of data is generated. Chemometric techniques such as principal component analysis (PCA), K- nearest neighbors (KNN), support vector machine (SVM) among others, can be applied to LIBS and Hyperspectral data for better classification and quantification purposes in copper ores. Real- time determination of elemental and mineral species used for online processing control will help to achieve the copper industry 4.0. INTRODUCTION The demand for copper mineral resources is intensely growing with the increase in population, per capita GDP, the development of new technologies and the increase in global living standard. With the rise in consumption of copper, it is important to optimize mining and metallurgical processes tending to the copper industry 4.0 (Ge, Song, Ding, & Huang, 2017). The real-time analytical assessment in the mining and metallurgical processes is a crucial part for allowing the global improvement in mining industry. The features considered for better analytical assessment are the instrumental automation and interconnection, real time results, low cost, quality in terms of accuracy and precision. Furthermore, improving recovery (extraction), timing and quality of final products avoiding environmental impacts. Some elements such as Cu, Fe, Ag, Au, Mo, S, As, Pb, Zn are important to be determined in the process control. Additionally, rapid mineral identification of few species such as CuFeS2, Cu4FeS5, FeS2, CuS, Cu2S, MoS2, Cu3AsS4, FeAsS, among other can be challenging.

Jan 1, 2019

By L. Haavanlammi

Iron is a significant component of all copper concentrates leached in the HydroCopperTM process. The metals in the concentrate are leached in a chloride solution by oxidation with cupric ions. Copper enters into the solution as a cuprous chloro¬complex. Iron dissolves at the same time in the ferrous form, but it is immediately oxidized to the ferric state. Oxidation is effected by sparging air or oxygen into the leaching reactors. Because the pH is 1 - 2.5, ferric ion precipitates as akaganeite (T<90°C) or hematite (T> 90°C). Arsenic, antimony and the main part of the bismuth co-precipitate with iron and report to the leach residue. Cupric leaching is faster than iron oxidation; thus, leaching of low-iron concentrates (secondary copper minerals) is quicker than leaching high iron concentrates (chalcopyrite). Pyrite does not dissolve during copper leaching, but is oxidized slowly at higher redox-potentials after the copper has been leached.

Jan 1, 2006

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By J. A. Bos, Z. Dai, P. Quinn, A. Lee

A flowsheet is being developed for processing Thompson ultramafic low-grade nickel ores. This type of ore is characterized by high content of serpentinized magnesium silicates which generate slimes during comminution. Flotation of this type of ore proves difficult due to problems associated with the slimes. The flowsheet, based on extensive laboratory and miniplant flotation tests, consists of two key components: desliming by hydrocyclones prior to flotation and using soda ash for pH control in flotation. Satisfactory metallurgical results have consistently been achieved in laboratory full circuit simulation and miniplant tests.

Jan 1, 2009

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008