Search Documents

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By J. E. Gill

"THE YEAR 1959 appeared to be a good one in which to attempt a summary of progress in the location and study of sulphide deposits in Canada because a temporary surplus of metals caused prices to fall and many geologists who had been working like beavers were suddenly not so hard pressed. So it was •decided to arrange a Symposium. The response to the call for contributions was excellent and the result is the interesting collection of papers that follow.Activity in the search for massive sulphide deposits has never been as intense as in Canada since 1954. That was the year when the airborne electro-magnetometer first became generally available on a contract basis. These instruments work best on massive sulphide bodies, as do most of the ground electrical survey devices, so much of the new information relates to these. It was decided, therefore, to focus attention in the preparation of symposium papers on such masses. This served also to keep the survey within reasonable limits."

Jan 1, 1960

By F. G. Pickard

"The Strathcona Concentrator is one of three concentrators presently operated in the Sudbury District by the Nickel Division of Falconbridge Nickel Mines Limited. Production commenced in 1968 at a milling rate of 6,300 tons per operating day. Milling capacity was increased in 1970 to 7,200 tons per operating day. 7he ore contains iron, nickel and copper primarily in the form of pyrrhotite, pentlandite and chalcopyrite, while the common gangue minerals are feldspar, quartz, mica, talc and chlorite. The primary function of the concentrators is not only to liberate sulphides from silicate gangue minerals but also to separate pyrrhotite from the more valuable minerals pentlandite and chalcopyrite.SummaryExcessive wear on steel liners and blinding of grates in a regrind pebble mill of the Hardy Concentrator was corrected by the use of rubber liners and grates. The success of these resulted in their installation as original linings In all grinding units except the rod mills at the Strathcona Concentrator. The operation of rubber liners and grates when sized mine ore was used as the grinding medium was satisfactory confirming the Hardy Concentrator experience. Problems developed when the grinding medium was changed from sized mine ore to steel balls in that blinding of the grates occurred. This resulted in conversion of the units to overflow type mills through removal of the grates. The lifter bar life was significantly increased by using higher lifter bars.Grinding PracticeOperation of a regrind pebble mill commenced in 1961 in the Hardy Concentrator. This operation demonstrated the economic feasibility of using sized mine ore as grinding medium. Problems caused by excessive wear of metal liners and grates combined with blinding of the grates were corrected in 1964 through installation of rubber liners and grates."

Jan 1, 1974

By M. Yavuz

As a branch of Operations Research, decision making is a widely used application in both science and social sciences. There are many different methods developed to solve decision making problems in the literature. In this study, Fuzzy Analytic Hierarchy Process (AHP) method is performed for the selection of reclamation project selection in an open pit mine and the optimal solution of the problem is investigated. Different reclamation project alternatives are prepared for an open pit mine, which continues to its production activities in magnesite sector in Turkey. The data obtained from Magnesite Cooperation is used in the application of the method. A decision-making process is prepared as considering the project alternatives for the purpose of selecting the most suitable reclamation project. The entire criteria that affect the decision-making process are identified and transformed into a hierarchical structure. The problem is solved by using Fuzzy AHP method developed according to this structure. It is found that Fuzzy AHP is a method that may help decision-makers in solving different decision-making problems in mining.

Aug 1, 2013

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By K. Peake, A. Dalvi, V. Hernandez, S. Chang, M. Oliazadeh

"Ironstone Resources Ltd. is developing the Clear Hills oolitic iron ore deposit in northwest Alberta, Canada. Sources of oolitic iron ore worldwide are abundant and ubiquitous, but there is currently no commercial technology to extract iron from oolitic iron ores. Mineral processing of the ore to generate a commercial iron ore concentrate is very challenging due to the nature of these ores. Accordingly, Hatch and Ironstone are developing a new pyrometallurgical process (Hatch Ironstone Chloride Segregation) to produce metallic iron from high silica and high phosphorus oolitic iron ores. Following the chloride segregation process, the treated ore is subjected to fine grinding. The iron is then separated by magnetic separation. The iron grade and phosphorus content of the final product shows a strong dependence on the separation methodology and the grind size. The pyrometallurgical process has been developed and tested at a lab-scale pilot plant. The commercialization of this technology could provide an opportunity for the development of a new alternate iron making technology. This paper presents the results of test work done on the raw iron ore to create a concentrate and also on the products of the pyrometallurgical process for the production of a high grade 90% metallic iron product.INTRODUCTION Oolite is a sedimentary rock formed from ooids – spherical particles with concentric layers. There are a number of large oolitic iron deposits where the mineralogical form features a low iron content and high concentration of impurities making them presently impossible to exploit on either a technical or economic basis. The fifteen largest oolitic iron ore deposits in the world are estimated to contain approximately 337 billion tonnes of iron ore, which would be a significant source of supply for worldwide steel production. A viable process that can economically recover iron from these oolitic iron ore deposits could become an important new technology to meet future demand in the steel industry. Hatch and Ironstone have demonstrated that oolitic iron ores can be exploited to produce direct reduced iron (DRI). Direct reduction ironmaking is a method for producing solid metallic iron using different techniques compared to the blast furnace process, which is the more conventional ironmaking route. The demand for the construction of direct reduction ironmaking plants has increased in response to the increasing demand for crude steel. It is viewed as a method of providing low-residual iron sources to scrap-based steelmaking in electric arc furnaces."

Jan 1, 2014

By Jean-François Dorion

La corrosivité des environnements miniers souterrains est un phénomène peu étudié au Canada. En plus de détériorer les systèmes de soutènement, la corrosion s?attaque aussi à divers installations et équipements souterrains. Cette étude, débutée en janvier 2007, est l?établissement d?une banque de données afin de caractériser les environnements miniers souterrains selon leur potentiel de corrosivité pour les systèmes de support de terrains. Pour ce faire, cinq (5) mines ont été sélectionnées afin de comparer les environnements : Laronde, Géant-Dormant, Niobec, Mouska et Doyon. À chacune des mines, trois (3) endroits ont été étudiés. Les résultats préliminaires démontrent une grande variabilité des conditions d?une mine à l?autre ainsi qu?à l?intérieur même d?une mine. La minéralogie des roches et du gisement influence la composition des eaux souterraines et la présence des sulfures joue un rôle important sur l?agressivité de l?eau et de l?air des mines de l?étude. Afin de déterminer le potentiel de corrosivité, plusieurs paramètres doivent être considérés et la mine doit être zonée selon l?agressivité des endroits.

Feb 1, 2008

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By Norman B. Davis

THE ceramic group of industries is comprised of those engaged in the manufacture of cement, glass, artificial abrasives, whiteware, including earthenware, stoneware, porcelain tableware, porcelain sanitary ware, electrical porcelain, floor and wall tile, porcelain enamel on metals, refractories of all kinds, sewer-pipe and structural clay products, such as terra cotta, brick, and hollow tile. The various sub-divisions of the industry produce a wide range of articles on which we depend for our creature comforts from day to day, perhaps to a greater extent than we generally realize. The industry, in turn, depends on a great number of minerals, and chemical products derived from minerals, and it is the object of this brief paper to present a list of these with notes indicating the particular applications. In order to bring home the importance of the industry to your daily life, stop and consider the many things around you accepted as a matter of course. Cement provides the smooth surfaces of many of our highways, city streets, and sidewalks. It enters into nearly all types of construction, alone or in combination with other clay products. Glass we hardly appreciate because we can see through it so easily, but it is there to serve us in windows, doors, and other light-transmitting structures. Glass is the universal means of transporting liquids and beverages, our beverages are usually served in it, and, with the recent development in fine spun glass textiles, there is a possibility of glass clothing in the future. Chinaware, a general term for table dishes, may be earthenware (not vitrified), semi-porcelain, or bone china, but it is before us three or more times a day ?and we seldom think of the minerals that have made these products possible. Floor tile, wall tile, and other ceramic specialties for interior and exterior use and decoration please the eye and provide sanitary surroundings.

Jan 1, 1938

By Zhiyang Long, Ruiling Xiao

"A mine shaft is one main development method of establishing access in an underground mine. The construction technology of the mine shaft sinking is complicated and large equipment setup on surface and in the mine shaft. The paper briefly reviews a single-line operation method, parallel operation method and mixed operation method as well as the features of the one operation method with the excavation, lining and installation. The special construction technology mainly would include ground freezing methods, full diameter shaft drilling methods, caisson methods, grouting technology and concrete curtain methods as well as other methods. The paper summarizes the shaft sinking numbers and effects by the special construction methods during different periods. The paper states the shaft sinking conditions and the each created record conditions in the coal, metallurgy, non-ferrous metal, hydropower, highway, railway, nonmetallic and other industries. The paper has a prediction on the shaft sinking requirements and development tendency in the future for China.INTRODUCTIONA mine shaft is one main development method of access in an underground mine. In recent years in China the new shaft mines represent 45% of the total number of new mines. With the development of new mining area under construction and the development of deeper mines, the ratio of the mine shaft as access for underground mines will increase. The construction technology of the mine shaft engineering will be complicated, the operation site footprint will be small and the working environment will be more difficult. The mine shaft sinking operation will often be varied by the geological conditions and affected by underground water inflows, seam gas outbursts, geothermal and other natural conditions. The safe construction of the mine shaft sinking will be challenged by all these conditions. Although the mine shaft engineering will only be about 5% of the total mine roadway engineering, the mine shaft construction period often will take over 40% of the total mine construction period. With the progress of modernized mine production technology and the construction of a high production and high efficient mine, the mine transportation roadways mostly would be set in the seam and the engineered amount of the mine rock roadways reduced year by year could cause more prominent long extensions of the mine shaft construction period. Therefore, in order to speed up the construction, to shorten the mine construction period and to realize the investment benefits as early as possible, the technical level of the mine shaft sinking should firstly be improved and the construction speed of the mine shaft engineering and sinking should be speeded up, which would have important significant benefits."

Jan 1, 2019

By Sergio Romo, Gerardo Fuentes, Adriana Garcés

Refractory ores with gold entrapped in a sulfide matrix, must be processed in a first stage with chemical or physical treatment in order to liberate the gold for a subsequent step with cyanide. The goal of this research was to compare the refractory behavior of a gold concentrate treated using two pretreatment methods: pressure oxidation and fine grinding. Gold concentrate from Viacha Mining in Bolivia, assaying 50.11 gpt, with a P80 of 131 ?m was used. The concentrate contains arsenopyrite and pyrite as main sulphides in the matrix. A preliminary test with cyanide resulted only 13.5% of gold extraction with 4 hours of stirred leaching. Using an autoclave oxidation with sulphuric acid and 12 bar oxygen pressure at 220°C pretreatment, the cyanide gold extraction increased to 69.0% in 4 hours. When material was ground in a pulverizer, producing a P80 of 20 ?m and the product directly cyanided, stirred leaching gave a gold extraction of 65% in 4 hours. For both techniques, the effect of temperature, sulfur produced in autoclave oxidation, optimization of the cyanide and the nature of residues were also studied.

Jan 1, 2014

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By D. Mark Richards

Highland Valley Copper (HVC) is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using GPS has been utilized at the mine since 1996 for blast hole drill navigation and since 2000 for shovel and dozer navigation. Since 1997, rock recognition has been part of the drilling process. This allowed the mine to develop a Mine to Mill strategy using the rock hardness information from drill monitoring systems to both refine drilling and blasting parameters as well as downstream crushing and grinding strategies. Although this preliminary effort has been very successful at HVC, the current intent is to gain further benefits through better use of existing information while also deriving an enhanced data set from monitoring production drills. In the latter case, the objective is to acquire and process drill variables in such a manner as to permit more detailed definition of rock mass characteristics. The subsequent focus will be to use the derived geotechnical and geological information as part of a practical process to more prescriptively blast the rock mass. Through the definition of domains based on drill monitored derived rock mass properties, the intent will be to enhance blast outcomes that lead to optimized downstream (from blasting through to concentration) processes in a more proactive and timely manner. This paper examines a proposed approach to be able to derive more accurate and consistent rock mass properties from production drilling. In addition, the discussion will identify potential benefits to be gained from process improvements that result in enhanced productivities, and crushing and grinding optimisation due to blasting strategies that are more closely matched to identify rock mass characteristics.

May 1, 2007

By Yongsheng Song, Yong Chen, Wenjuan Li

"Detailed characterization and improved recovery of a micro-fine, low-grade refractory gold ore from a beneficiation plant in Yunnan Province, China, was investigated. Different analytical techniques, such as videlicet size analysis, scanning electron microscopy, and mineral analysis by a Mineral Liberation Analyser, were used for mineralogical characterization of the ore. This paper describes an experimental study on the effect of the grinding fineness and the use of various flotation reagent regimes involving collectors, depressors, and activators on the flotation behaviour of micro-fine auriferous pyrite. Two-stage flotation resulted in high gold grade (32.71 g/t) and gold recovery (80.02%) of the bulk gold concentrate. This process opens the possibilities of maximizing Au recoveries in a micro-fine low-grade refractory gold ore where low recoveries are common.INTRODUCTIONWith the rapid development of the gold industry, refractory gold ores are becoming increasingly important resources for gold production (O’Connor & Dunne, 1994; Agorhom, Skinner, & Zanin, 2012). Among these refractory gold ores, sulfur and micro-grained native gold ores represent a significant challenge, since they are not amenable to gold recovery by direct cyanidation. The gold contained in this type of ore is very finely disseminated and encapsulated in sulfides, which makes it inaccessible to the cyanide solution during direct cyanidation (Bulatovic, 1997; Allan & Woodcock, 2001). Autoclave pressure oxidation (AC POX) of the sulfide ore and subsequent cyanidation is a common technology used to recover the gold in such types of ore. Flotation is often used as a pre-treatment method to refractory gold ore (Monte Lins, & Oliveira, 1997).As the gold-carrier minerals are usually finely disseminated (sometimes under 10 µm) and intimately associated with gangue minerals, a fine grind is necessary to get a high degree of liberation. At the same time, the fine grind usually causes the production of significant quantities of slimes, which comprise easy-to-float gangue minerals such as mica, dolomite, and calcite. These mineral phases are naturally hydrophobic and float readily, competing with the value minerals in the froth phase and resulting in lower concentrate grades."

Jan 1, 2016

By Dirk van Zyl

The world is consuming more and more electronic products every year. This has caused a dangerous explosion in electronic scrap (e-waste) containing toxic chemicals and heavy metals that cannot be disposed of or recycled safely. But this problem can be avoided. We are pressing leading electronic companies to change; to turn back the toxic tide of e-waste. Every year, hundreds of thousands of old computers and mobile phones are dumped in landfills or burned in smelters. Thousands more are exported, often illegally, from the Europe, US, Japan and other industrialized countries, to Asia. There, workers at scrap yards, some of whom are children, are exposed to a cocktail of toxic chemicals and poisons.

May 1, 2008

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018