Search Documents

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

By M. H. Haycock

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By A. Brown

The swift decline of coal during the period of unprecedented expansion in the Canadian economy is a phenomenon deserving careful examination, because the underlying forces contributing to this decline may have broader implications in our national economy. At the present level of technology, coal is more difficult to process, transport and utilize than liquid and gaseous fuels. Fundamentally, it is a matter of limitation in technique. Because coal is a vast store-house of energy in Canada, the reduction of these limitations is in the long-term national interest.

Jan 1, 1967

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By Philip W. Johnson, Charles D. Haynes

"Abstract - The coalbed methane industry has become a prominent source of domestic natural gas, with its technology having evolved over the past 30 years. Whereas most coalbed methane wells are able to produce without major interruption over their economic lives, wells operating in an underground mining area are subject to being mined-through. If mine-through occurs, the productivity of the well is at least compromised, and may even be terminated. The economic consequences of mine-through may be relatively simple if mineral ownership and extraction rights are common for the coal and coalbed methane. However, if ownership is not common and a superior coalbed methane lease exists, the coalbed methane ownership must be compensated for lost production caused by mine-through. This paper presents a relatively straightforward method to calculate the value of the lost production caused by the mine-through. It uses technology from mining and petroleum engineering, as well as simple economics and financial management techniques.Sommaire - L’industrie de la production de méthane houiller est aujourd’hui une source importante de gaz naturel domestique dont la technologie a considérablement évolué au cours des trente dernières années. Bien que la plupart des puits de méthane houiller peuvent être mis en production durant l’entièreté de leur vie utile sans interruption majeure, les puits implantés en périphérie de mines souterraines sont sujets à être recoupés par ces dernières. Un tel recoupement peut compromettre, ou même mettre fin à la production d'un tel puits. Les conséquences économiques du recoupement par une mine souterraine peuvent être relativement simples quand les droits miniers et les droits d’extraction sont détenus en commun pour le charbon et le méthane houiller. Si toutefois ces droits ne sont pas détenus en commun et qu’il y a eu octroi d’une concession de méthane houiller de qualité supérieure, les détenteurs du méthane houiller doivent être compensés pour la perte de production résultant du recoupement par une mine souterraine. Cet article présente une méthode relativement simple pour calculer la valeur des pertes de production suite au recoupement par une mine souterraine. Cette méthode fait appel aux technologies de l’industrie minière et pétrolière ainsi qu’à des techniques simples d’économie et de gestion financière."

Jan 1, 2006

By C. A. Hardie, G. F. Leichtle, J. A. Finch, J. A. Watson

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibres for use in newsprint. The mineral processing group at McGill University, in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network), has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University’s flotation column test work at a Québec wastepaper recycling facility. IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world’s largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and United States municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year, but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World’s solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity."

Jan 1, 1999

By A. D. Burns, K. M. Nikolaisen

Electrolytic reduction followed by the addition of sulfuric acid and the application of heat can be used to selectively crystallize uranous sulfate from solution. This approach, when coupled with downstream thermal decomposition, forms the basis of a process for primary uranium recovery and purification where much of the sulfuric acid value can be recovered and recycled. In this process, a purified uranium (VI) leach solution is first electrolytically reduced to uranium (IV) in a membrane electrolysis cell. Sulfuric acid is then added to the solution which, in conjunction with the input of heat, causes the crystallization of uranous sulfate tetrahydrate. The precipitate is then dried and thermally decomposed to U3O8, which releases a mixture of high-purity SO2, SO3, oxygen, and water vapour. This gas can be recovered as sulfuric acid in an existing acid plant, processed through a new wet sulfuric acid process, or absorbed directly into the upstream electrolyte as a substitute for fresh acid in the crystallization step. This process has been shown to be practical, efficient, and cost-effective on the laboratory scale, and could be practiced on the industrial scale using commercially available equipment. This paper focuses on the thermal decomposition process and options for acid recovery.

Jan 1, 2020

By Stephen van Duin

As productivity in coal extraction demands increase in underground coal mines, the industry is faced with finding new ways to support production without jeopardising safety. In modern mines the capacity and scale of longwall coal extraction has steadily increased to a point that support processes are failing to keep pace. In particular, roadway development is continually placed on the critical path of activities which maintain mine production, so any inefficiency in this area is quickly exposed. Original equipment manufacturers are under immense pressure to modify their machines to be more interconnected with each other, with machine communication and logistical sharing of space becoming a known requirement. This paper looks at the changing trends in mining practice, analysing available technology as well as currently emerging research into hard automation and discusses the need to integrate machinery and processes in order to see increases in productivity and safety.

Aug 1, 2013

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980

By Brian A. Ferguson, Raynald O. Vezina, Marielle Gaudet, Raoul R. Boissonneault

"Kiena has been committed to developing a fresh management and employee relations approach since the commencement of production in 1981. The functional organizational structure encourages joint participation and commitment on the part of all employees to common goals in safety and production. The results over the last four years have been extraordinary. Kiena won the John T. Ryan Canada Trophy for 1983 for its safety record and has experienced a steadily increasing productivity through the application of new mining equipment and technology in the hands of a well-trained and motivated team of employees.This paper serves to highlight the fact that productivity, safetyand technical innovation are closely linked to employee participationand involvement which are likely to be the key to theCanadian mining industry's survival in the years ahead.This presentation follows up on an earlier unpublished paper, given at the 84th Annual Meeting of CIM in Quebec City in April, 1982, which discussed the philosophy and the planning which took place before implementation of the management and employee relations system at Kiena. This present paper reviews and expands on material given in the earlier work. IntroductionThe mining industry, which has always been considered as rather conservative in its approach, has experienced with some regularity, cyclical periods related to metal prices. These cycles, previously foreseeable to some extent have become less coherent over recent years during which time the industry has had to face fierce international competition. The issue to productivity is without doubt the major concern of the mining industry in Canada today and it represents the greatest challenge facing us during the present decade. Developments that have been made in mining technology over the precious two decades have failed to completely produce the significant advancements in higher over-all productivity that were expected."

Jan 1, 1987

By John C. Luck Jr.

"DEVELOPMENT of oil emulsion mud dates back to the early days of rotary drilling when oil was added to the drilling mud solely for the purpose of freeing stuck drill pipe. After the drill pipe was freed, and drilling resumed, this oil was considered a contaminant. Efforts were made to remove the oil but some of it remained and was emulsified with the drilling mud, thus forming a mechanical emulsion.During the late 1930's, operators found that adding crude oil to drilling muds seemed to alleviate 'sticky-hole' problems and so oil was allowed to remain in the mud. This practice was adopted when it was found that faster drilling rates and longer bit life were obtained. These observations led to the development of emulsion drilling muds. During the past five years their application has become more widespread because of the lower fluid losses obtained, greater lubrication qualities, faster penetration rates, and generally better hole conditions.An emulsion may be defined as a two-phase system consisting of a mixture of either finely divided oil droplets in water or of finely divided water droplets in oil. The surrounding liquid is known as the continuous phase. The emulsifiers reduce the interfacial tension, making the droplets tend to repel each other so that they remain dispersed and stabilized. These emulsions are classified as oil-in-water or as water-in-oil, depending upon whether water or oil, respectively, is the continuous phase. Briefly, close inspection shows that they consist essentially of globules of• the one liquid suspended in a continuous mass of the other liquid. Oil emulsion muds are usually of the oil-in-water type. Two basic types of emulsifiers •commonly used in Canadian muds are soaps and lignites."

Jan 1, 1954

By Peter C. Jones, Wanda M. Carter, David H. Watkinson

"Abstract - Pyrrhotite, chalcopyrite, and pentlandite are the dominant sulfide minerals in the 740 zone of the Kelly Lake orebody (Inco Ltd.), Copper Cliff Offset, Sudbury. Petrographic and quantitative electron microprobe analyses of minerals, from sulfide assemblages and host quartz diorite, of the 740 deposit have revealed three processes that have affected sulfide mineralization and associated sulfarsenide and platinum-group-mineral (PGM) distribution: magmatic, hydrothermal, and tectonic. Accessory, zoned cobaltite, and gersdorffite occur in sulfides as a result of these three processes, and PGM occur dominantly in hydrothermally remobilized and deformed ores. Where PGM are present in sulfarsenides they provided nuclei for sulfarsenide growth. Solitary PGM are orders of magnitude larger than those PGM found within sulfarsenide minerals. Five varieties of PGM occur, michenerite and sperrylite being the most common, with lesser froodite, hollingworthite, and ruarsite.The effect of a deformation is a localized fabric in the ore, revealed by pyrrhotite and chalcopyrite bands; pentlandite porphyroblasts also partially define the foliation. The deformed ore is also characterized by alteration of the adjacent quartz diorite, which produced an alteration assemblage including almandine garnet, Fe-rich biotite, and chlorite."

Jan 1, 2001

By M. Sanchez

In the last decades, the Chilean copper mining and metallurgical industry have had to modify their technological processes to meet the environmental regulations implemented by the Chilean government, and also to support the pressure of the public opinion. Thus, air quality standards for sulfur dioxide and particulate matter (primary and secondary), plans for reducing emission of arsenic by the Chilean copper smelters, effluents discharge limits, among others regulations were applied by the environmental agency. Additionally, agreements on cleaner production were carried out by mining sector and government. Now, a draft law on mine closure, and another on environmental mining wastes (abandoned mines) are being discussed by the authorities and the mining sector. In the context, production and environmental impacts in different ways to produce copper in the Chilean mining industry are reviewed and regulatory tendencies as well as abatement technologies today used are exposed and discussed in this presentation. Pyro, hydro and electrometallurgical processes employed and their current effluent and contaminants are presented showing various alternatives of treatment in the copper industry. An update of regulations established in Chile vis a vis copper production, with an especial attention to mine closure are also presented.

Jan 1, 2007

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By F. H. Samuel, A. M. Samuel, H. R. Ammar

Casting imperfections, such as porosity, in cast aluminum components greatly influence their fatigue properties. The effect of porosity on the fatigue life of 319-F and A356-T6 aluminum alloys was studied, where the porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The results show that porosity has the most detrimental effect on the fatigue life: 92 % of all tested samples fractured due to porosity acting as the main crack initiation site. In the absence of casting imperfections, other microstructural aspects such as slip bands can be responsible ( 4 % ). The porosity was investigated in terms of the pore size at the sample fracture surface and its location i.e. near the edge or close to the interior. It was found that porosity located far from the sample surface (edge) has less influence on the fatigue crack initiation, and the fatigue life decreases as the size of the pore located at the sample surface increases. Aluminium

Jan 1, 2006

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By N. A. Beier, N. Slingerland

"Oil sands tailings impoundments rank among the largest (spatially) in the world, covering a total of approximately 220 km2 of northern Alberta, Canada. A preliminary geomorphic design for an oil sands tailings storage facility (TSF) landform was completed with the goal of eventual closure and delicensing in mind. This paper outlines methods identified during the design process that streamline closure when implemented early in the mine planning and TSF design stages. With most oil sands TSFs currently in active operation (and some still in the planning stages), geotechnical engineers and mine planners have the opportunity to make operational and design decisions, such as those outlined herein, that are likely to improve the geotechnical and environmental performance of the landform post closure. ¦ KEYWORDS Alberta, Athabasca oil sands (AOS), Landform design, Reclamation, Sand dam, Tailings storage facility (TSF) RÉSUMÉ Les bassins d’accumulation des résidus issus des sables bitumineux font partie des plus grands (en termes d’espace) au monde, et couvrent au total environ 220 km2 dans le nord de l’Alberta, au Canada. Une conception géomorphologique préliminaire a été réalisée pour le modelé d’une installa¬tion de stockage des résidus (ISR) issus des sables bitumineux en gardant à l’esprit la fermeture et le retrait de permis à terme. Cet article présente les méthodes identifiées pendant le processus de conception qui simplifient la fermeture lorsqu’elles sont mises en oeuvre dès les premières étapes de planification de la mine et de conception de l’ISR. La plupart des ISR issus des sables bitumineux se trouvent dans des exploitations actives (dont certaines en sont encore aux étapes de planification), aussi les ingénieurs géo¬techniques et les planificateurs miniers ont la possibilité de prendre des décisions en termes d’exploita¬tion et de conception, telles que celles présentées ici, qui pourraient améliorer la performance géotechnique et environnementale de la phase suivant la fermeture du modelé. ¦ MOTS CLÉS Alberta, assainissement, barrage de sable, conception du modelé, installation de stockage des résidus (ISR), sables bitumineux de l’Athabasca (SBA)INTRODUCTION The Athabasca oil sands (AOS) underlie 140,200 km2 of land in northeastern Alberta, Canada. Oil sands located within 100 m of the original surface account for 4,800 km2 of the total area and are considered to be economically mineable (Figure 1; ERCB, 2009). Bitumen, the thick, tar-like substance contained in the AOS, is extracted through open-pit mining and in-situ methods. During mining, the overburden is first removed as waste and the sandy, bitumi¬nous ore (“oil sand”) is transported to processing facilities via conveyor belts and 400 t trucks. Warm and hot water, as well as process aides such as caustic soda, are mixed with the oil sand, creating a slurry from which bitumen is mobilized and extracted. The resulting slurry waste product is called “tailings” and contains mineral solids, process water, and small proportions of unrecovered bitumen (Masliyah, Zhou, Xu, Czarnecki, & Hamza, 2004; Sobkowicz & Morgenstern, 2009)."

Jan 1, 2019

By Bruce Mennie

PT Freeport Indonesia (PTFI) operates copper and gold mining operations in a mountainous area of the Mimika regency, near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. The mining and concentrating operations typically produce 240,000 metric tonnes per day of Copper and Gold ore from the combined mining of an 80,000 tonne per day (ore) block cave operation (DOZ Mine) and a 160,000 tonne per day (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open pit mine will be complete in 2016 at which time PTFI?s operations will convert to Underground. Mining operations will transition from today?s mixed surface and underground operation to full underground mining over the next 6 years. This paper reviews the history of Redpath?s relationship with PTFI, beginning with a raiseboring contract in 1981 and evolving into vertical and horizontal development contracts of up to 37,700 equivalent metres of lateral development and 4,000 metres of vertical development in 2011. An overview of the current operations (PTFI?s Grasberg Open Pit and DOZ Underground Mines) and transition period (challenges for the transition from current to future underground mines) is presented with details of development of common underground infrastructure and future mines; Big Gossan Mine, DMLZ Mine, Grasberg Block Cave Mine, and the Kucing Liar Mine.

Oct 1, 2010

By N. V. Mel'nikov

This paper discusses the reserves of oil, natural gas and coal in the USSR, with particular attention to the future role to be played by coal in supplying the energy fuel resources of the country.

Jan 1, 1972

By F. E. Lathe

RECENT events have emphasized with renewed force the well known fact that war greatly intensifies the demand for certain metals, particularly for iron, copper, and zinc. Any increase in the use of iron and steel, whether in war or peace, is also accompanied by increased consumption of those metals which find their chief application as ferro-alloys, such as nickel, chromium, manganese, molybdenum, tungsten, and vanadium. Further, since high temperatures are essential for the production of all these metals, activity in the metal industry is inevitably accompanied by an insistent demand for refractories. For example, in North American practice the consumption of magnesitic hearth refractories is frequently expressed in pounds per ton of steel. This quantity (not including straight dolomite) ranges on individual plants from about 7 to 12 pounds. When the industry is operating at approximately full capacity, the ratio of refractory to steel tends to increase, since the tonnage of steel produced is recognized as of paramount importance, and this leads to the harder driving of furnaces and less regard for the effect on refractories. It should also be observed that the cost of refractories per ton of metal produced is always so low, in comparison with other items, that it may even increase while the cost of metal per ton is being reduced through more continuous operation and the use of higher temperatures. As one prominent Canadian copper metallurgist has tersely expressed it, he is "not in business to save refractories but to smelt ore". The effect of war demands and of general industrial activity upon the production of basic and neutral refractories is clearly shown in Figure 1, which gives the value of chrome ore and magnesitic-dolomite produced in Canada during the period 1907 to 1937. Tonnages have not been shown, as these are not available for the full period; such figures as have been published from time to time are not strictly comparable, since both raw rock and finished products have on occasion been included. The preliminary figures for 1938, which are now available, have been prepared by the Dominion Bureau of Statistics on a different basis from those immediately preceding, and have therefore not been shown.

Jan 1, 1940