Search Documents

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration . Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet ,Processing the are as received resulted I n 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J."

Jan 1, 1988

By Wenxue Chen

This paper presents a new type of bolt with full thread and uniform strength, and fabricated with a Glass Fiber Reinforced Polymer (GFRP) bolt-making machine designed by the authors. The mechanical performance of the new bolt is assessed with strength tests conducted with the bolt in acid, alkaline and saline water conditions, with increasing concentration. The purpose is to test the new GFRP bolt?s mechanical performance in harsh conditions, especially metal mines with acid or alkaline environments. Comparison of the color, weight, size and antistatic ability of the GFRP bolt before and after it is immersion in solution is presented. Changes in tensile and shear strength, torsion, and anchoring force were evaluated in the laboratory. The results show that the mechanical properties of the GFRP bolt are more sensitive in alkaline than in acid and saline water. However, the loss ratio of mechanical properties of the GFRP bolt is very small according to the results of tensile and shear strength, torsion and anchoring force. The new bolt can be useful for applications in acid or other harsh mines.

Aug 1, 2013

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By G. G. Bowser

PERUSAL of a list of present-day commercial explosives perhaps does not convey a full realization that there has been a great deal of improvement since the original dynamite was discovered nor that, in recent years, great developments have taken place in specialized explosives. This is true particularly of high-explosives for use in metalliferous mining or what is more commonly termed 'hard-rock' mining. Not many decades ago, only two or three types of explosive were avail-'able for commercial use. One was black blasting powder. Another was ordinary nitro-glycerin dynamite in various strengths. Black blasting powder remains with but very little change. Despite its ancient lineage, it is still with us as perhaps the sole explosive in use today which is almost identical in appearance, physical properties, and working ability or execution co the original. Which dynamite the story is different. Its evolution may be likened to that of the dog, nitro-glycerin as first discovered being the counterpart of the wild dog and, like it, dangerous and hard to control. The original dynamite as made by Nobel might then be considered as representing the first domesticaced species. This original dynamite, however, has been 'crossed with other bloods' until one sees now many distinct 'breeds' in the list. Present-day explosives still have the 'bark' and the 'bite', but with control and research have come many improvements; and types have been created which are specially adapted for particular kinds of work. We still have the direct descendant of Nobel's dynamite in the form of an improved nitro-glycerin dynamite. This C-I-L explosive, Polar Dynamite, is no longer the best type to use in the hunt for gold, silver, iron, and other metals. There have been developed other explosives more suitable for chat work. In Canada, such explosives are accomplishing this work effectively, not only where climatic conditions are moderate but through the rigours of our northern winters, with their sub-zero temperatures.

Jan 1, 1938

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By J. J. Crowder, A. L. Coulson

Ground support is a significant component of underground mining costs. The rehabilitation of failed support, however, is often much more expensive than the initial installation. This paper investigates whether the right type and length of support can be designed correctly the first time, through forward modelling of the support and the mining process. Back analyses demonstrate how high-quality instrumentation and monitoring can help with the estimation of the post-peak (post-failure) rock mass parameters required for a comprehensive analysis. A hybrid modelling approach combines a three-dimensional mine-wide boundary element model with a non-linear finite element model to allow for the failure process in the rock mass. The back analyses demonstrate that, for the case study site, the post-peak Generalized Hoek-Brown value of mr must be reduced significantly in order to properly simulate displacements observed in instrumentation data. High-quality instrumentation data is the key to post-peak rock mass parameter calibration. The procedures outlined in the paper highlight the need for a new hybrid numerical modelling package that can use the influence of three-dimensional mining-induced stresses to predict displacements in, and potential failure of, rock masses surrounding mining infrastructure in order to radically alter strategic and tactical mine design.

Jan 1, 2007

By Jay Tuttle

THE spiral stoping method of mining was first seen by the writer at the Granby Consolidated Mining, Smelting & Power Company's Hidden Creek mine, at Anyox, British Columbia. Where the method received its name, or by whom it was named, is a question, but it was employed by the Granby Company at their Phoenix mine, in the Boundary district, B.C., as early as 1901-02 after they had tried unsuccessfully other methods at that large, law-grade property. its adoption there was suggested by two miners, John and Steve Swanson, then working at Phoenix, who had previously been employed in the hard iron-ore mines of Michigan and Wisconsin, where they had learned this system of mining. The method proved successful at Phoenix and also, later, at the Company's Hidden Creek mine at Anyox, where some 40,000,000 tons, or more, of ore was mined in this manner during a period of about thirty-five years.

Jan 1, 1939

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

By L. A. Homeniuk, R. Bonnar

"The Athabasca Basin has been the scene of an intense exploration effort since the late 1960s, resulting in the establishment of this area as one of the major uranium districts in the world.The A thabasca Group is of Helikian age and unconformably overlies metamorphic rocks of Aphebian and Archean age. Most of the known uranium deposits have a close spatial relationship with the unconformity, graphitic meta-sediments, major northeast-trending structures and the basin edge. It should be noted that, in regard to the latter, some of the Cluff Lake deposits are exceptions.The pre-Helikian rocks underlying the Athabasca Group have been divided into six Iithostructural domains. The known uranium deposits are concentrated in the Wollaston and Mudjatik domains in the southeastern portion of the basin.The orebodies typically have a narrow high-grade portion below the unconformity and a broader, lower-grade disseminated zone in the overlying sandstone. Over-all grades average over 1% U3O8 and our estimate of known reserves totals more than 400 million pounds of contained U3O8. Some of the deposits have high concentrations of other metals, including nickel, arsenic, cobalt and gold. Ubiquitous chlorite and clay alteration is characteristic of the orebodies.Other Proterozoic basins in Canada of similar ages and having analogous geological settings to the Athabasca have received far less attention. Although little of the known uranium mineralization in these basins is related to the Helikian unconformity, there may be an exploration potential for deposits similar to those of the Athabasca basin.IntroductionThe Athabasca sedimentary basin is located within the Churchill Structural Province of the Canadian Shield in Northern Saskatchewan. The basin is elliptically shaped and is approximately 800,000 square kilometres in area.The objective of this paper is to summarize the various elements in the genesis of the unconformity-type uranium deposits of the Athabasca Basin and to evaluate the comparative potential of other Proterozoic basins to host similar unconformity-type deposits."

Jan 1, 1982

By V. Chatain

The environmental assessment of historical mining sites contaminated with various inorganic species, as also the determination of remediation targets require a better knowledge of pollutant-bearing phases. The objective of this paper was to investigate the operational fractionation of arsenic (As) in an As contaminated (ca. 3 wt%) soil collected from a gold mining site in France, where mining activities and smelting processes of gold ores took place until 2004. Single and sequential chemical extraction procedures were performed to evaluate the potential mobility of As according to the fractions to which it was associated in the contaminated soil, and also the part of As sorbed onto soil particles. These procedures used provided information on the nature of As fixation processes in the mining soil studied. Results showed that As appeared mainly sorbed (ca. 72%) with iron on the soil particles, in particular amorphous iron oxyhydroxides. These results confirmed a potential risk of arsenic mobilization under acidic and/or reducing conditions, which frequently occur in mining environment. This research evidenced the importance of the knowledge of As-bearing phases to better predict the mobility of this pollutant and in turn improve the management of As contaminated sites.

Aug 1, 2013

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

By M. M. Hajdasinski

"Any study in the field of theoretical investment analysis, or practical project evaluation, must be based on the assumption of one of the commonly applied models of time and value representation, and the corresponding interest convention. The lack of clear assumptions in this regard may easily confuse both the author of the study and the reader, and sometimes even lead to inaccurate results.In the first part of this paper formal definitions of the continuous and discrete models of time and value representation are introduced; in the second part, the importance of transparent assumptions is shown using a concrete example of inflation calculation in project evaluation.IntroductionIn his recent paper, L.D. Smith(10) discusses an important aspect of mine investment analysis: inflation in project evaluation. His interesting presentation of current practices of handling inflation by Canadian and international mining companies in their feasibility studies ends, in the conclusions, with a call for clear assumptions made when evaluating mining projects.With this call, an important issue has been addressed. The lack of clearly stated assumptions, or their incompleteness, are relatively frequent with regard to the interest convention or the model of time and value representation assumed when evaluating mining projects. It is, for example, fairly common that the quantitative evaluation of a project is performed according to the discrete model of time and value representation and the discrete interest convention, and the graphical presentation, supporting this evaluation, reflects the continuous model.Sometimes such an ambivalency means nothing more than just a formal inconsistency; there are cases , however, that may well lead to a serious confusion and /or to inaccurate results . Before this can be demonstrated on a specific example, a concise description of the models of time and value representation used in the evaluation of industrial projects seems to be in order. Although these models (especially the discrete one) have been in common use in the research and practice of financial analysis for considerable period of time, they have been applied rather intuitively, and their forma] definitions are difficult to find even in the standard textbooks on Engineering Economy."

Jan 1, 1990

By J. B. De Hart

In the September issue of the Bulletin, 1923, there is a paper by J. A. H. Church on "The Spontaneous Combustion of Coal in Mines", which is more or less a general discussion of the subject. Mr. Church gives a list of mine fires which have occurred in Alberta. Of the total of thirteen fires, six are attributed to spontaneous combustion. Of these six fires, it will be noted that five are in thick pitching seams. These fires occurred in the following mines during the years shown, at Frank in 1909; at Lovett in 1916; at Cadomin in 1920; at Yellowhead in 1922, and at Cadomin in 1923. Every one of these fires has occurred, as Mr. Church points out, in a seam of over 12 feet in thickness, and furthermore not one of these fires has been extinguished, although in every case large sums of money were expended and considerable risks . taken in fire fighting. Now it is quite evident from these facts that mines working seams of this nature are faced with a very grave danger and it behooves us to study the matter and endeavor to arrive at some practical method of preventing the loss of our coal mines from this cause.

Jan 1, 1924

By William Petruk, J. R. Schnarr

The behaviour of minerals during flotation of a fine-grained pyrite-rich base metal ore was investigated by studying the feeds. concentrate and tailings from every flotation cell in the mill of Brunswick Mining and Smelting Corp. Ltd. Bathurst. New Brunswick. The samples were analyzed for Zn, Pb, Cu. Fe, Ag. Sb, Sn, Bi, In. Hg, Mo and As. Mass balances were computed and recoveries of all metals from each cell. from each circuit and from the mill were calculated. The percentages of sphalerite. galena and chalcopyrite occurring as free grains in each product were determined with an image analyser, as were size analyses for free mineral grains and middling particles, and compared with screen analyses. The results show that the behaviour of minerals is defined much better by the recovery of free mineral grains than by the recovery of elements. The recovery of free sphalerite in the zinc circuit is 96 wt %, whereas Zn recovery from the same circuit is 88 wt %. the difference being due to unliberated sphalerite. The recovery of free sphalerite from the mill feed is 88 wt % and Zn 78 wt %. The recovery of free galenafrom the mill feed is 88 wt % and Pb 64 wt %. The recovery of free chalcopyrite is 75 wt % and Cu 45 wt %. Size analyses show that more sphalerite and chalcopyrite can be liberated by regrinding. but the galena is so fine grained that regrinding would not necessarily improve liberation. Silver occurs mainly in tetrahedrite and galena; the main loss in the tailings is due to large (+ 26 um) and small (-1 um} free and unliberated tetrahedrite grains.

Jan 1, 1981