Search Documents

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By E. W. J. Thornton

During the past six or seven years extensive research has been performed on ore samples procured at the Bruns1,vick Tin Mines which is located in the south-west corner of New Brunswi.ck. This property was originally staked by Mount Pleasant Mines and they did considerable metallurgical and geological work on a small copper, zinc and tin deposit. In 1969, the property was obtained by the Sullivan Mining Group and after much geological and diamond drilling work, an entirely separate ore body \Vas located two miles south of the previous workings. The major economic metals in this ore zone are tungsten, bismuth and molybdenite, but many other metals exist as well. As the ore contains a host of different mineral species, it can be seen that considerable time WRS required to develop a practical flow sheet.

Jan 1, 1977

By S. Fuentes, J. Cáceres

"During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs.This paper describes improvements in mine design, mine planning, and mine management, including methods enabling the Chilean and international mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low-cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine. IntroductionDuring the last fifteen years, block caving mines have experienced huge changes in designs, planning and administration. These changes have permitted operators to drastically reduce costs, improve equipment productivity, and improve overall business performance. As a consequence of this situation, the block/panel caving mining system is challenging actual open pit operations to maximize the net present value (NPV)."

Jan 1, 2004

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By Karl J. C. Harries

"9.1. INTRODUCTIONIn Chapter 5 of Volume I royalties are dealt with and several topics would appear to be duplicated in this Volume. However, Volume I may be looked upon as a general guide, whereas this Volume is a reference volume. It deals in considerable detail with specific provisions and concepts relating to royalties between private parties. This does not, however, mean that Chapter 5 can be ignored. It should be looked upon as a source of general information concerning royalties between private parties and as a negotiating aid intended to give an overview of various topics. You may well find that in its general approach it will lead you to ask a question which, hopefully, will be dealt with in this Volume .It should be remembered that royalty agreements are agreements with a particular focus, and so the concepts set forth in Chapter 1 apply to them. This chapter addresses a few considerations specific to royalties that will usually form part of an agreement rather than a stand-alone agreement.9.2. FORMAT FOR ROYALTY PROVISIONSIn many of the cases where royalties arise, they are adjunct to, or part of, other arrangements. For example, a royalty may form part or all of the consideration to be given to an owner upon purchase of his property, or it may arise if a joint venturer ceases to contribute to the venture and has his interest converted to a royalty.1 It is with such situations that this section primarily deals; if the royalty is contained in an agreement that is singularly, or primarily, concerned with creating it, then it is just a normal agreement.Commonly, by the time the right to receive the royalty arises, at least some of the other provisions of the agreement have been performed and/or become redundant. For example, in an option agreement the royalty will be a continuing obligation of the optionee, usually arising only after the option has been exercised.2 In a joint venture agreement, a royalty will often arise where the interest of a non-participating venturer has been diluted and converted to a royalty, in which case the recipient will usually become a passive party, entitled only to his royalty, and most of the rights that he enjoyed as an active venturer will cease to be effective."

Jan 1, 2003

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By E. H. Henderson

MR. R. V. NEILY stated that he had at one time operated at Goldenville. The practice and results are much the same now as in the olden days. Inside plates were then found to be a source of trouble and had been removed. At the Libbey mine, Queen's county, the sulphides carried considerable gold, and $45.00 to $60.00 per ton had been recovered from the concentrates by roasting and chlorinating. Later, concentrates were treated with bromocyanide. Following that practice, a cyanide leaching plant was installed, which did not require concentration of the tailings. Cyanidation brought a recovery of around 95 per cent, with but $300 worth of plant. In Nova Scotia, the ore of each locality presents an individual problem of its own as to treatment required. Ma. W. B. Timm stated that, in the majority of Nova Scotia gold ores, more than 75 per cent of the gold content is free-milling and, naturally, stamps are most efficient for collecting and amalgamating this gold. In Ontario and the West, they had got away from stamps, and perhaps the main reason was that the supply of battery-men, who came from Nova Scotia, had died off. Ball-mills had been installed, which required smaller space and handled large tonnage, even though, as far as amalgamation goes, the stamps were probably more efficient. If concentration is to be done, ore from stamps is usually in better shape for recovery in passing over the tables, as there is no slime. With the ball-mill, flotation is necessary. The better practice, undoubtedly, is to take out what gold is possible before it is all smashed up, as in the ball-mill, though recent developments in the ball-mill make it possible to trap and take coarse gold directly from the mill. In this way, cyanidation is speeded-up, due to saving of the time the coarse gold would take before going into solution. PROFESSOR A. E. FLYNN found it unusual in these days to read anything in favour of the stamp mill, and thanked Mr. Henderson for the excellent paper in which he upholds the stamps and backs his opinion with facts from actual operations. For the typical Nova Scotia ore, containing coarse gold, stamps are un¬excelled. It used to be said that the virtue of stamps is that they brighten the gold for amalgamation. Although this saying is almost classical, it is not true, for gold is never brighter than in the native, untouched state. Any hammering that gold gets makes it more difficult to amalgamate.

Jan 1, 1935

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By Julie Dénommé

Today few in business would argue with the idea that we are living in a world that is Volatile, Uncertain, Complex, and Ambiguous. Coined VUCA by the US Army War College, these four words define the ?turbulence? and ?continuous white water? that the business literature has been documenting for the last decade. This VUCA world became even more relevant to business in 2007 when the Institute for the Future fellow Bob Johansen published the idea of transforming VUCA into Vision, Understanding, Clarity, and Agility. We call this VUCA Prime (VUCA'), and place an infinity loop (8) between them to show their dynamic interaction. This paper presents an exploration of the impact of VUCA 8 VUCA' on business and the conditions under which these dynamic forces help to successfully navigate change.

Oct 1, 2010

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By Pierre Sauvé, Guy Perrault, Armand Savoie, Pierre Trudel

"La Mine Doyon est une entreprise détenue à parts égales par Cambior Inc. et par Minerais Lac Ltée qui en est l'opérateur. Les statistiques de production au 1"" janvier 1990 indiquent que, depuis le début de son exploitation (1980), 10.3 Mt de minerai d'une teneur moyenne de 5,9 g Au/t ont été usinées. Les réserves sont estimées a 10,4 Mt à une teneur moyenne de 6,6 g Au/t jusqu' à une profondeur de-450m.Trois zones minéralisées sont présentement en exploitation. Ces zones sont caractérisées par la présence de veines de quartz-pyrite accompagnées localement de chalcopyrite. Les roches encaissantes sont les schistes a séricite (zone# 1), les roches volcaniclastiques de composition felsique (zone #2) et intermédiaire (zone #2, zone ouest) ainsi que les roches intrusives appartenant au pluton de Mooshla (zone ouest). Toutes ces roches ont subi un métamorphisme régional dont l'intensité correspond à la limite supérieure du facies schiste vert ( -425°C}.Les zones minéralisées sont situées à I' intérieur des zones de déformation et d'altération les plus intenses. L'étude des structures mineures nous indique que la région a subi plusieurs épisodes de déformation ductile a fragile qui sont antérieurs, contemporains et postérieurs al a minéralisation. L'analyse structurale indique également que la déformation majeure est associée à une importante phase de compression orientée N-S a NNE-SSW.L’ensemble des observations suggère que la minéralisation et I' altération associée sont de type épigénétique. La mise en place du minerai se serait effectuée à la fin de l'épisode principal de métamorphisme et de la déformation."

Jan 1, 1990

By D. J. Hallbom

This paper presents a novel methodology for the hydraulic design of mine backfill distribution systems. The ?operating range? method uses the concepts of the hydraulic grade line and equivalent pipe length to determine flows and pressures as the pipeline route and static head change over the life of the mine. The operating range method is easy to learn because it is semi-graphical and uses well-known design concepts (e.g., the hydraulic grade line) and slurry design models (e.g., the Durand deposition velocity model). However, by changing the paradigm in which these concepts are used, the operating method allows all potential pipeline cases to be analysed simultaneously without the need to know the exact pipe routing. It also allows the hydraulics engineer to quickly identify ?pinch points? and ?slack flow? zones, to estimate the effect of changing the size or length of any given section of pipe, to assess the impact of changing the material properties of the backfill slurry, to size the slurry pumps, and to size and locate rupture discs when required.

May 1, 2007

By Ian D. Pirie

Presentation outline ?Project location ?Geology ?Resources and reserves ?Results of the FEED study ?Social and environmental considerations ?Project path forward

May 1, 2010

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016