Search Documents

By G. J. Ackland, K. Saksl, F. Brunke, M. Kohnke, B. Tegner, C. Siemers

The application of titanium alloys is limited to 550°C due to their poor oxidation resistance. It is known that the addition of niobium decelerates the oxidation of titanium alloys whereas elements like vanadium do not improve titanium’s oxidation resistance. The underlying mechanisms are not yet well understood. In the present study, different binary titanium-niobium and titanium-vanadium alloys as well as commercially pure titanium were investigated. Oxidation experiments were carried out at 800°C up to 288 hours followed by metallographic analyses to study the oxide layer morphology as well as the microstructure at the interface. Energy-dispersive X-ray spectroscopy mappings were used to identify possible changes in the distribution of the alloying elements. In addition, micro-focused hard X-ray experiments were performed to layer-wise analyse the phase composition in selected samples. As expected, the niobium containing alloys show a better oxidation performance compared to commercially pure titanium and the titanium-vanadium alloys. The oxide layer consisted of TiO2 and Ti2O3. Depending of the niobium content, a niobium-rich layer developed below the metal-oxide-interface minimising oxygen diffusion into the titanium matrix. Based on these results, the minimal niobium content needed for improved oxidation resistance was identified so that alloys of technical relevance can now be developed.

Jan 1, 2014

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By Margarete Kalin

"Difficulties arise in implementing environmental technologies in the mining sector because important fundamental processes, which lead to the environmental degradation, are ignored. Weathering rates, the role of bacteria in the process and the incomplete application of the matching principle of accounting at the time the mining disturbance take place. Mining is a multi-stakeholder activity and the environmental problems have multivariate dimensions also effecting process.The limiting factors in the contaminant generation process are the transport of oxygen by advection, convection or diffusion in air or water and the associated microbial activity. Weathering products are transported from the mineral surface by atmospheric precipitation to surface and groundwater. This contamination takes place at different rates, requiring a long time to evaluate technological choices.Restoration efforts have to focus on slow reaction rates in the contaminant generating processes. Technology, which does not address the reaction rates and is selected based on inappropriate time scales, will not provide long-term solutions. Natural approaches to reduce acid generation, based on Ecological Engineering principles have required decades of research and field testing, but now show promise in addressing the cause of AMD and ameliorating its effects."

Jan 1, 2005

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By Keith Eldridge, Robert Kelly

"Quality management has a/ways played an important role at the Iron Ore Company of Canada; particularly since the early eighties when the iron ore markets favoured buyers as opposed to sellers.Since thot time, IOC's quality system has evolved from basic quality control to the Deming philosophy and its 14 points, and on through various other phases to the ISO 9000 series.ISO 9002 Registration was' first requested by IDC's customers and development plans were prepared in 1988. At this time, Quality System Registration was unheard of in the mining sector and TDC found itself struggling with the concept. The 1U!Xt three years saw the company develop a Quality System to meet ISO 9002 in a two phased approach, setting new standards for the mining industry when registration was achieved in December 1991.The company now sees ISO Registration as the cornerstone of its future quality efforts. IOC's quality system has been integrated with several other initiatives such as loss control and functional training, both of which focus on training and management the workforce to do the job safely, the right way.This paper addresses the steps required to develop a quality system for the mining industry within the guidelines of the ISO 9000 Series and the subsequent integration of other quality related initiatives."

Jan 1, 1994

By Leslie F. Sawatsky

Each potential oil sands developer deals with the question of optional sources of raw water to supply large water demands that range from 50 to 80 million cubic metres per year for each of six existing and planned developments. The Athabasca River currently supplies nearly all of the water to the existing mines via conventional bank intakes, which has resulted in some concern over the effects of reduced river flows. This paper describes the various water supply options, and the likely scenario for future oil sands water supply projects. Various water supply options have been suggested including Athabasca River water via infiltration galleries, groundwater, combined Athabasca River water and alluvial groundwater using wells (i.e. bank filtration systems), diversion of tributary rivers, utilization of large lakes in the region and pumping from other large rivers in the region. Investigations show that the size of river catchment needed to support raw water usage by a typical oil sands mines exceeds 5,000 km2 eliminating all tributary rivers that are located in the oil sands region except those rivers with large drainage areas like Firebag and MacKay Rivers. Lakes cannot be used as a source of supply due to large water deficits for smaller lakes and the large cost of sourcing water from a lake as large as Lake Athabasca. A groundwater source alone would not likely meet the large water demands. River intakes on the Athabasca River will likely continue to be the most practical water supply option for oil sands mines north of Fort McMurray, although various types of Athabasca River intakes are possible. Existing intake systems include screened riverbank intakes, forebay intakes, and river bottom intakes. Infiltration galleries are not feasible for most sites, though some bank-filtration-type systems using high capacity wells may be an option if there is sufficient thickness of high-permeability alluvium at a suitable location in the Athabasca River valley.

May 1, 2004

By Euler De Souza

This paper presents a study conducted to assess sillmat behaviour during undercut mining and to provide a comprehensive understanding of the effects of arching and sillmat thickness on stability. The design study investigated the effects of such parameters as stope width and height, closure strains, orebody geometry and inclination, wall roughness, fill properties and cure time on the stability of cemented sillmat during undercut mining. Arching effects have been quantified based on centrifuge modeling studies for the different mining conditions. Observations have indicated that the degree of arching is a function of stope geometry, wall roughness, fill cohesion, and wall closure. Arching effects increased with decreasing stope width, increasing backfill cohesion and frictional resistance, increasing wall roughness and with wall closure.

May 1, 2002

By Karl J. C. Harries

This paper looks briefly at some of the agreements and types of royalties that may be met during exploration activities, but does not go into details relating to them. Agreements can either make or break a deal or relationship. A well drafted, comprehensive and fair agreement can create good relations and trust among the parties and will go a long way towards making a deal work. In the best of all worlds the agreement will be put away and not need to be referred to after it has been signed (but it will be there if needed to sort out potential problems). On the other hand, a poorly drafted agreement or one that is inappropriate to the circumstances or unfair to one of the parties can break a deal and end up with the parties facing each other in that expensive, unproductive and time-consuming occupation ? a lawsuit. Accordingly, it is advisable to involve professional advisers with any agreement. The straightforward one may involve no more that a read through whereas the more complex agreement will require considerable involvement. There is, however, one rule for every explorationist to remember: a professional adviser is only an adviser. His responsibility is to make sure that you have the necessary information to make a reasoned decision but the decision is yours, not the adviser?s. It is your deal, you are going to have to live with it, and it is inappropriate for an adviser to introduce new concepts or amend negotiated ones without your specific instructions. Mineral exploration agreements, although basically option, acquisition and joint participation agreements, come in all the shapes and forms, appropriate to give effect to the endless variety of deals negotiated by the ever-active minds of explorationists. You will note the reference to "joint participation agreements" rather than "joint venture agreements". The latter term was purposely avoided because, with the current activity of explorationists from common law jurisdictions in civil law jurisdictions, it has become necessary for the explorationist to become familiar with corporations and shareholders agreements. As most of you are no doubt aware, under the civil law system a joint venture is normally not recognized as a legal entity and, therefore, joint participation in projects is usually by way of corporations.

May 1, 2003

By Benoit Bissonnette, David Gelderland

"The Campbell Mine Constructed Wetlands has been in full operation, processing effluent from the water treatment plant of the mill circuit for the last two years.The overall results are extremely positive with dramatic improvements for the originally targeted parameters – Ammonia, Copper and toxicity.• Ammonia concentrations were reduced from an average of 5 mg/L to an average of 0.43 mg/L which translates to an average reduction of 91%.• Copper concentrations were reduced from an average concentration of 0.054 mg/L to an average of 0.019 mg/L, which translates to an average reduction of 65%.• LC50 Acute toxicity testing revealed no impact.• IC25 Chronic toxicity tests revealed no impairment to growth or reproduction.As a result of the improvements in discharge water quality from the wetland, 100 percent compliance with respect to all Certificate of Approval, MISA and MMER regulations for effluent will be consistently achieved.The system has proven to be very easy to operate and maintain, with a minimum of care. Given some basic rules are followed, the construction of the wetlands was straightforward and relatively inexpensive compared to other treatment methods.The ecological benefits of the operation of the wetland are also quite substantial, as is the positive image of the corporation in environmental stewardship.INTRODUCTIONOver the last four years, Campbell Mine has adopted an aggressive schedule for the development of wetlands for use as the final stage of effluent treatment within the tailings management facility. The focus of this work has been to utilize natural biological systems to provide Campbell Mine with a 100 percent compliant water quality with respect to all MISA, MMER and COA discharge criteria at all times throughout the effluent discharge period."

Jan 1, 2003

By Mory Ghomshei

Pebble Creek Geothermal Power project is associated with a massive recent volcanic eruption in Southwestern British Columbia Canada. Slim holes drilled to depths 1100 m in the prospect area, show very high temperature gradients around 80?100?C/km. The temperature and chemistry of the Pebble Creek hot springs indicate the possibility of a steam reservoir in the prospect area. In addition to high temperature gradients, presence of host rocks with high permeability, along with abundance of recharge waters (from the Lillooet River) provides clear signature of a high-grade geothermal power reservoir at depth 2000 to 3000 m. Data show that over five hundred Megawatt of green power can be generated from the prospect area in a commercially viable manner. The generated power will be base-load, which in comparison with large hydro has the advantage of lower capital costs and a significantly smaller footprint. The final hurdle to overcome, before starting the development phase, is deep exploratory drilling for resource confirmation. This paper is a summary of the data available on the Pebble Creek geothermal power prospect, presented in the context of viability of the resource for large-scale commercial power generation.

Aug 1, 2013

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

By M. Dupuis

It has been previously demonstrated [l] that there is no obvious thermal balance related issue limiting the size of a Hall-Héroult cell. Yet, it is well known that a forced-air sidewall cooling system is part of the AP50 cell design [2], In the present study, the authors analyze the impact of thermal loading on the mechanical deformation of high amperage cell potshells. The effect of adding cooling fins or a forced-air sidewall cooling system is then assessed.

Jan 1, 2005

By Mike Johnson, Greg Andrews, Niels Verbaan, David Dreisinger

"The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper INTRODUCTIONSearch Minerals Inc. (Search) is exploring and developing a number of deposits for rare earth element (REE) recovery in Labrador, Canada. The Port Hope Simpson District is in the southeast of Labrador and is highly prospective for heavy and light rare earth elements. The Foxtrot deposit sits within the Port Hope Simpson REE District (Figure 1), which is 70 km long by up to 10 km wide. The infrastructure available at Foxtrot is excellent; a deep-water port, air strip, and road and power infrastructure are pre-existing at St. Lewis. The three communities of Port Hope Simpson, St. Lewis and Mary’s Harbour are in close proximity to the site."

Jan 1, 2016

By C. Robinson

The Diavik Diamond Mine is located in one of the most remote and forbidding places in the world, 220 kilometres south of the Arctic Circle and on the bed of a vast northern lake, Lac de Gras. A single road, built out of ice and crossing frozen lakes, connects the mine with other operations and Yellowknife, the capital of the Canada's Northwest Territories. Diamonds were first discovered in the Lac de Gras region in the early 1990s, and construction of the Diavik Diamond Mine was completed in 2003. Diavik currently mines three kimberlite pipes. Open pit mining has now concluded and all three pipes are mined using underground mining methods. In early 2010, Diavik began mining and processing initial ore from its new underground mine; underground mining operations are expected to continue beyond 2020. The initial mine ventilation system was an exhausting (pull) system with fresh air supplied by a fresh air raise and a main ramp. Return air was exhausted via two raises and a secondary ramp. The system had a total flow capacity approximating 401-411 m3/s. With planned increased production and with changes in mining method, it has been proposed to change the mine ventilation system to a positive (forcing) ventilation system in order to meet projected increases in flow requirements of 566-708 m3/s. Extensive engineering work was developed in order to successfully achieve the changes in system configuration. In the proposed configuration, the main ramp is in an exhaust configuration and exhaust raises are converted to fresh air raise. A number of system implementation options were investigated and phased plans for system execution have been developed. The proposed changes to the ventilation system are substantial and involve extensive construction work. Work was commenced in 2011, each planned phase has been successfully completed to date, and system changes continue today in order to achieve complete system flow reversal and increased flow distribution. This paper details the design of the modified ventilation system and commissioning work which will allow the mine to meet its future production targets.

Aug 1, 2013

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By Humphrey Dean

"Canadian mining companies now operate numerous Koepe-type friction hoists in a variety of different shafts, most of which have a depth in excess of 3,000 feet. Rope performance reliability is an absolutely essential ingredient of most installations and, for this to be provided, a more comprehensive understanding of rope reactions to applied stresses is required.It is the intent of this paper to illustrate for the operators the importance of the critical stresses encountered and to provide a maintenance program designed to circumvent potential difficulties."

Jan 1, 1970

By R. Mulligan

"The Cordilleran tin belt extends from the Seward Peninsula in westernmost Alaska to Mexico. Throughout the Canadian section, tin occurrences are mainly confined to a belt along the northeastern fringe of the Western Cordilleran sub-region; the boundary of this sub-region with the Eastern Cordilleran sub-region is most simply defined as the practical eastern limit of granitic and metamorphic rocks. The stratified rocks underlying this restricted belt are mainly late Precambrian and early Paleozoic miogeosynclinal sedimentary rocks, which are more or less metamorphosed but otherwise are generally equivalent to the less severely deformed rocks underlying the Eastern Cordilleran sub-region. They contrast with Late Paleozoic - Mesozoic eugeosynclinal volcanic-sedimentary assemblages farther west, but the granitic intrusions throughout are mainly of Late Mesozoic age. Thus, narrowly defined, the tin belt largely coincides with a lead-zinc-silver metallogenic province, whereas copper deposits characterize the eugeosynclinal regions to the west. In addition to the tin occurrences, which include the Sullivan lead-zinc-silver mine, Canada's only significant producer, the belt contains all the beryllium, most of the tungsten and many Iithophile-type molybdenum occurrences. Several types of occurrences of each metal are represented. Lithium occurrences in the Canadian Cordillera are notably rare, and these few are insignificant."

Jan 1, 1971