Search Documents

By M. Kawata, T. Amano, T. Miyamoto, K. Shibayama

"The High Pressure Acid Leach (HPAL) plant of Taganito HPAL Nickel Corporation (THPAL), located in Taganito, Philippines, with a nameplate capacity of 30,000 Ni-t/year started commercial operation on October 2013. The plant load was smoothly ramped up and it achieved monthly production equivalent to 33,000 Ni-t/year in 2016. Partial improvement of the plant capacity for the achievement of 36,000 Ni-t/year, as evaluated from the current operation progress of each system is planned for 2017. In this paper, aside from presenting the progress of the plant ramp-up, research and development activities such as the reduction of nickel loss and the improvement of filtration capacity which was achieved by particle size control of ZnS precipitates in the Zinc Removal system are also discussed.INTRODUCTION Taganito HPAL Plant Project History of THPAL Taganito HPAL Nickel Corporation (THPAL) was incorporated in August 2008, as a joint venture of three (3) companies, namely Mitsui Corporation with 15% share, Nickel Asia Corporation (NAC) with 10% share and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 75%. Aside from its capital share, NAC’s Taganito Mining Corporation (TMC) supplies the ore for the HPAL plant located in Taganito, Claver, Mindanao, Philippines. The objective of THPAL is to produce 30,000 MT of nickel and 2,600 MT of cobalt as mixed (Ni/Co) sulfide by treating nickel laterite ore in the Philippines and exporting to Japan as raw material for SMM’s Niihama Nickel Refinery (NNR) for the next 30 years. In other words, 1.15 wt% of nickel in ore is refined to 99.99 wt% nickel in electrolytic nickel. The mixed (Ni/Co) sulfide is shipped to NNR and SMM provides the technology and management personnel to THPAL plant as well as sulfuric acid which is the main reagent for HPAL process. Figure 1 shows the location of THPAL and current relationship between the stake holders.The Characteristics of THPAL Plant In terms of plant design, a 2-train system is applied for the HPAL circuit considering the reliability of the process, facility and avoidance of whole plant shutdown due to HPAL troubles. The technical data, operation know-how and improvements gained from the successful operation of Coral Bay Nickel Corporation (CBNC) which was established in April 2002 were reflected in THPAL’s plant design. As for the H2S plant, a more economical design was considered which is different from CBNC."

Jan 1, 2017

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By K. Svens, M. Lahtinen, L. Lehtinen

"Outotec's direct leaching process is an atmospheric leaching process for sulphidiczinc concentrates. The direct leaching process, based on special leaching reactors developed by Outokumpu and leaching know-how, is the most economical way to produce electrolytic zinc. The newest industrial-scale application of Outotec's direct leaching process will be started up in 2008 in China at Zhuzhou smelter. The process isintegrated to the existing production plant, replacing part of the old production facilities by modern technology and increasing the production capacity significantly. The process equipment supplied by Outotec includes also tailor-made reactors designed on the basisof the work and experience of Outotec Research Centre."

Jan 1, 2008

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By S. D. Tolgyesi

Kidd Creek Background ? Located in Northern Ontario, Canada ? Underground base metal mine ? Operating since 1966 ? Total of 125Mt mined to date (2.43% Cu, 6.60% Zn) ? Current plan at 2.4Mt/Y (6575t/D) Current Practices ? Evaluating stope margins to ensure that value is added ? Scheduling sulphide and Cu stringer ore to limit oxidation in passes ? Scheduling to maintain uniform grades to concentrator ? (SOPs highlight problem stopes on mine plans, and limit blast sizes in those stopes which may contain sulphides prone to oxidation) ? Scheduling high-Pb stopes to avoid spikes to concentrator ? Providing weekly, monthly and long-term forecasts ? Reconciling mine and mill production ? Underground grade and dilution estimates by mine supervision ? Terminate mucking when grade becomes sub-economic ? Laser cavity surveys to provide feedback and improve Designs Cut-off Grades ? Ore value is obtained from copper, zinc and silver ? Ore outlines at 2% copper equivalent used to guide stope planning; sulphide outlines obtained from contacts while copper stringer outlines drawn from block model (kriged) ? Datamine block model and CADD software used to evaluate alternative stope shapes ? Stopes classified as waste, incremental, or full-cost based on margin calculations for each stope ? Incremental ore may be mined if it does not displace fullcost Ore Conclusions ? Grade control remains an important function for optimizing the ore extraction at Kidd ? The scope of the function has changed to a scheduling focus ? A change in grade control practices over time has not led to significant changes in concentrator feed ? The lead and iron sulphide content of the ore display upwards trends and may require more attention in the future ? The key function of field observations has shifted to flagging exceptions and terminate mucking at grade cut-off

May 1, 2003

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

This paper outlines the position and capabilities of Western Canada&apos;s bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By J. Olaf Sund

"THE November issue of the Bulletin carried in it ""Origin of the New Bruns1viclc Gypsum Deposits"" by J. Olaf Sund. This paper was a digested account of a Master's thesis at the University of New Brunswick which was a very useful compendium of information of gyp-sum in New Brunswick. It was a warded the President' s Gold .Medal and the First Prize in the Graduates' Section of the Students' Essay Competition. The present writer presents his congratulations to the winner of the competition. At the same time he must comment on the use of certain terms and on certain conclusions presented in the paper.The term ""unconformable"" has been used in several places in the paper to describe the relationship of gypsum to anhydrite in various deposits in New Brunswick in a sense which is quite alien to the accepted meaning. It has long been known tl1at the gypsum at the surface or near the surface in deposits in the Atlantic Provinces has come from hydration of anhydrite by surface and ground waters. The gyp-sum must be looked upon then as an alteration or even a weathering product. It cannot in this sense be called ""unconformable"" and thus arguments using the word in the accepted sense are invalid."

Jan 1, 1960

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984

By Heribert F. Broicher

By the very nature of mineral deposits the quality of the raw material generally fluctuates and should be known for optimum processing. Early classification, for example, of limestone into road-metal grade or lime grade or of run-of-mine ores into high grade, low grade and waste as well as information for blending or for dosage of reagents are prerequisite for economic processing. Non-contact, real-time and on-line rock identification or assessment of quality parameters can be realised by introducing the analysis of laser-induced fluorescence (LIF) into the mining industry. LIF analysis is an optical method evaluating the basically known photoluminescence properties of matter, however, extending the application into hitherto unimagined fields by use of high-energy pulsed lasers and time-resolved analysis of fluorescence in the ultra-violet, the visible and near-infrared domains of light. LIF analysers and test work in a limestone quarry and a cement plant in Germany as well as in an iron ore mine in Sweden are described. First results of test work are available and proof this technology to be promissing.

May 1, 2002

By R. C. Wallace

Since the time when Canada&apos;s East and West were joined by the railway, and communication was established into the interior, settlements grew on the southern fringe of the great Precambrian area that formed the northern protaxis of the continent during its vicissitudes of growth. They clung precariously to the fringe of that ancient land, for the Precambrian is not generous to those who wish to live by the fruits of the soil, except in those limited areas where the Pleistocene ice-sheet has been profuse in its gifts of clay to cover the hard surface of the Precambrian rock. Later settlements spread westwards over the expanse of Cretacean plains that now form the wheatfields of the Canadian West; but there still remained in northern and western Ontario, in eastern and northern Manitoba, a pioneer race, to whom agriculture had attractions only in so far that it provided the wherewithal to lay siege to the riches of the Precambrian. And they had a vision beyond their time. More than they knew, they had seized the fact that for the complete rounding out of Canadian national life, a8 well as for the establishing of the necessary contributions towards the economic stability of Canada and its provinces, an industry in mining sh01.dd be well and truly built in the hinterland of the central provinces. Failing the winning of mineral from the rocks, and timber from the forests, there would remain between the East and the West an enormous barrier of unproductive country which would not only be an incubus to the agricultural people in their struggle for economic liberty, but would effectively, and for all time, remain an un-populated void across which the aspirations of East and West would be unable to unite.

Jan 1, 1924

By R. P. Viljoen, A. L. Sokolov

"The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth&apos;s crust including ancient platforms, mobile belts and zones of tectonicmagmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonicallycontrolled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian platform, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu mineralization. It does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By F. S. Thurner

This paper, a description of the new ore-unloading and stockpiling facilities at the Sydney Works of DOSCO Steel Limited, deals with a new approach to arrive at the most economical solution to combine ore unloading facilities for common bulk carriers and for different types of self-unloading vessels. Also discussed is the design and installation of a 1-mile-long steel-cord belt conveyor sys-tem with a most modern type of mobile belt conveyor stacker, along with automatic and semi-automatic controls for the entire ship-unloading and stockpiling operations.

Jan 1, 1968

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969