Search Documents

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By J. Budac, J. Dennett, D. Mayne, P. Nawrocki

"The Nickel/Cobalt operation in Fort Saskatchewan, Alberta has successfully used an oxidative ammonia leach process to refine a variety of feeds into high quality nickel and cobalt products for over 60 years. Fundamental changes to the refining process were made when the major feed was converted from nickel concentrate to cobalt rich mixed sulphides in the early 1990s. Since the early 1990s, the production capacity of the refinery has expanded to match increases in both mixed sulphides and other feeds. In addition to increasing the production capacity of the refinery, other changes have been required in order to improve the operability and reliability of the refinery as well as to deal with increasingly stringent safety and environmental requirements. This paper describes recent changes at the refinery including changes to the flow sheet, improvements in unit operations, incorporation of new feeds, management of byproducts, and control of impurities.INTRODUCTION The Cobalt Refinery Company (Corefco) plant in Fort Saskatchewan processes nickel-cobalt mixed sulphide intermediate produced at the lateritic nickel mine and high-pressure acid leach (HPAL) facility in Moa Bay, Cuba. Both operations are jointly owned and operated by Sherritt International and General Niquel of Cuba. The mixed sulphide, along with other feed materials, is processed at the Fort Saskatchewan refinery using a pressure ammonia leach-hydrogen reduction process to produce nickel and cobalt metal. This refinery was originally constructed in 1954 to treat nickel concentrate from Sherritt’s Lynn Lake mine in Manitoba. (Benson and Colvin, 1964; Boldt and Queneau, 1967; Forward, 1953; Forward and Mackiw, 1955; Kerfoot, 1989) From the mid-1970s until the early-1990s, the facility operated as an independent refinery, treating nickel-bearing feeds from around the world. The flowsheet was changed in 1992 to address the increased cobalt content of the feed. (Cordingley and Krentz, 2005; Kerfoot and Cordingley, 1997) The flowsheet was adapted further in 2009 to improve cobalt speciation in the leach process, which allows better cobalt-nickel separation. The 2009 iteration is shown in Figure 1. Three ammonia leach stages were used to ensure high recoveries of nickel and cobalt. Underflow solids from the final leach stage contained mainly iron oxides. One of the features of the leach process is the innovative recycling of ammonia. Ammonia vented from the leach process in tail gas and from atmospheric tanks is recovered and recycled into the refinery using water based scrubbers and a high pressure distillation process. Indeed, roughly 250 t NH3/d is recovered as distillate and recycled back into the process. Also, air enriched with ammonia which is vented from the later first stage autoclaves is recycled to the lead first stage autoclaves to maximize oxygen and ammonia utilization."

Jan 1, 2017

By A. Christoffersson, T. Nillson-Wullf, H. R. Manouchehri

"Mining industry has been the building blocks for human development through millennia and will continue to play its role in sustainability and meeting society’s needs for raw material. In the way towards sustainability, the next generation of efficient and heavy duty of Sandvik’s crushers, CH860 and CH865, are introduced for efficient crushing. As the secondary, tertiary and/or pebble crusher, these new crushers are designed to over perform in tough mining environment. Featuring higher crushing forces relative to the mantel diameter and 500 kW motor, combined with advanced automation system, i.e., sophisticated HydrosetTM and Automated Setting Regulation (ASRTM), combined with overpressure system with dedicated air supply in dust collar, etc., the new crushers provide higher safety, productivity, and reliability with the same foot-print of conventional cone crushers.Since crushers are more energy efficient than mills it makes sense to effort in fine crushing to save energy and protect environment. That has been the logic behind development and introducing stronger and more efficient crushers by Sandvik. The results on crushing hard iron and gold ores by CH865 have proven its efficiency in fine crushing at a higher productivity, availability and reliability rates through increasing throughput for defined size fraction and extended crushing chamber liner life.Within this paper the performance of the CH865 to deal with two different ores are presented discussed with a glance at how the downstream milling process can be benefited by saving energy and reducing the operation cost. In plant practice, the implementation of the new CH865 provides between 25 and 30% of the crushed ore in the size range of first step milling, i.e., < 2 mm, that offers opportunity for reduction in energy consumption in milling and even changing the process plant configuration by directly forwarded that part to gravity separation. Furthermore, potential of converting the rod mill to ball mill to improve productivity has been considered by plant engineers. Furthermore, some potential applications for such efficient crushers are brought into considerations and discussed. The new developments provide about 30% higher crushing force to efficiently deal with competent ores and pebbles. The CH860 and CH865 crushers are well suited to replace conventional secondary and tertiary crushers respectively; nevertheless, CH865 is virtual option for pebble crushing in SAG and AG milling circuits."

Jan 1, 2016

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By James R. Hein

Manganese nodules form at the sediment surface of abyssal plains throughout the global ocean at water depths of about 4000-6500 m. The nodules form a continuum from purely hydrogenetic (all metals from seawater) to purely diagenetic (all metals from sediment pore waters), which will determine which metals of potential economic interest are enriched in the nodules. Another important factor in metal enrichment is whether diagenesis in the bottom sediment is oxic or suboxic. There are several nodule fields in the deep ocean that have received much attention with regards to economic potential, the most important being the Clarion-Clipperton zone (CCZ) in the NE Pacific, where the International Seabed Authority (ISA) has signed 12 contracts for exploration areas, each spanning 75,000 square kilometers. Those nodules are rich in nickel (mean 1.3 wt. %), copper (mean 1.1 %), and manganese (28%), with moderate amounts of cobalt (mean 0.2%), molybdenum (587 g/t), and lithium (129 g/t). A conservative estimate is that there exists 21,100 million dry tonnes of nodules in the CCZ, yielding more manganese, twice the nickel, three times the cobalt, and four times the yttrium than the entire land-based reserve base (economic plus marginally economic plus subeconomic reserves) for each metal. Total rare-earth elements (REEs) as oxides average 0.09% in CCZ nodules, a potential byproduct even at that grade because the heavy REE complement averages 26%, compared to less than 1% for the large land-based carbonatite REE deposits. The price for HREEs is much greater than for the light REEs. For comparison, the REEs in deep-ocean ferromanganese crusts are 3 to 5 times greater than nodules and the HREE complement averages 18%. Of the 12 CCZ contracts, 7 are with States (China, France, Germany, Japan, Korea, Russia, and a group of States (IOM); and 5 are with companies: G-Tec Sea Mineral Resources NV, Nauru Ocean Resources Inc. (NORI); Tonga Offshore Mining Ltd (TOML), UK Seabed Resources Ltd (Lockheed UK), and Marawa Research and Exploration Ltd. Three other nodule fields that have received attention are in the Peru Basin, which has nodules very rich in manganese (34%) and lithium (mean 311 g/t), the Penrhyn Basin (Cook Islands Exclusive Economic Zone), with nodules very rich in cobalt (mean 0.4%); and the Central Indian Ocean Basin (CIOB), where India has an exploration contract with the ISA. CIPB nodules have mean nickel, copper, and manganese contents of 1.1%, 1.0%, and 24% respectively.

May 1, 2013

By Seher Ata

"Virtual reality, a three-dimensional computer generated environment, has become recognized delivery system for many forms of education. This article describes the application of virtual reality to mineral processing education. An interactive mineral processing visualisation module has been developed at University of New South Wales (UNSW), Australia. The module provides students with an overview of a base metal concentrator, details about each stage of the process, as well as revealing how the mined ore progresses from stage to stage. The module also involves developing a number of instructional based plant layouts and flowsheets in the virtual environment that are intended to assist the user in understanding the essential components of the base metal concentrator.INTRODUCTIONVirtual Reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through a host of technologies such as three-dimensional graphics, audio feedback and special peripheral devices to produce interactive environments.VR has been used in diverse fields including medicine (Riener & Harders, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Schofield, Lester, & Wilson 2005; Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 2014). VR is also becoming recognized delivery system for many forms of education, including engineering education (Bell & Fogler, 1996; Bell & Scott, 1998; Shin, 2002). For example, virtual laboratories have been designed and developed to teach students fundemental features of the heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron making process (Babich & Senk, 2009) and to guide students to identify various safety measures while working in real laboratory (Bell & Fogler, 1996)."

Jan 1, 2016

By David W. Smith

"This paper is devoted mainly to a discussion of the hydrocarbon potential of the offshore, with a few brief remarks concerning the inorganic mineral potential.OFFSHORE OIL AND GAS POTENTIALIN ORDER TO HAVE HYDROCARBON ACCUMULATIONS, we must satisfy three basic requirements. First, we re-quire a sufficient thickness of sedimentary rocks which contain some porous and permeable formations to act as reservoirs. Second, we require some type of trapping mechanism, such as faulting, folding or stratigraphie trapping. Finally, we require that large quantities of hydrocarbons have been generated within the sedimentary rocks and have migrated to the traps."

Jan 1, 1969

By François Robert

The rate of new mineral discoveries in Canada has been declining in the last two decades. In response to the challenge and to stagnating investments in mining-related R&D, twenty Industry partners, supported by PDAC and Natural Resources Canada, established in 2010 the Exploration Innovation Consortium (EIC). This Consortium seeks to promote the discovery of new resources in Canada through coordination and sponsorship of industry-focused innovative and collaborative research and technology development, as well as training and education in mineral exploration. The two main themes of the integrated R&D program focus on exploration targeting in Deep and Mature Environments and in Remote and Covered Terranes.

May 1, 2011

By R. B. Rao, B. Das, J. K. Mohanty, D. S. Rao

Physical, mineralogical and geochemical characterization, along with some beneficiation approach to pre-concentrate the Ni content of the chromite overburden material of the Sukinda Valley, India, have been carried out in detail. Mineralogically, the overburden consists of geothite, quartz, hematite, magnetite and secondary silicates in varying proportions. A specific Ni mineral phase is absent in this material with the Ni and Fe being mostly enriched in finer fractions. Distribution of Ni and Fe in various size fractions and increase of Ni with increase in Fe (goethite content) indicate that goethite is the major Ni-bearing mineral phase. Quantitative estimation of goethite from chemical analysis and weight loss data indicates that the goethite quantity varies from 40% to 90%. Electron microprobe analysis (EPMA) indicates that Nirich and Ni-poor goethite are present in the overburden material. A sequential dissolution study indicates that more than 50% of the Ni are present within the goethite lattice as a lattice substitution. The results of pre-concentration studies (size classification, gravity, flotation and magnetic separation) indicate that Ni is richer in finer fractions. Further, the enrichment of Ni content is limited to 1.1% with 50% recovery by classification followed by hydrocyclone separation of the below 53 m m fraction.

Jan 1, 2000

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By Robert D. Brown, Robert B. Parsons

"Careful tax planning and proper attention to the regulations can result in an optimum deduction ""of the 25% federal resource allowance. Introduced in the Income Tax Act in1976, in part to compensate for the disallowance of provincial mining taxes and royalties. the 25% ""resource allowance"" is a permitted deduction in computing taxable income from mining and petroleum. However, the rules relating to the deduction are complex, and the importance of the deduction which can readily exceed 25% of net income- is frequently underestimated. This month, Tax Notes discusses the basic rules of calculating the resource allowance, and suggests some tax planning aspects which may warrant consideration.May 6, 1974 - "" .. . our provinces have adjusted royalties, mining taxes and other arrangements to derive what they perceive to be a fair share for the benefit of their people. However, a provincial resource is also a national resource... I am proposing that revenues derived by provincial governments in respect of production from a… mineral resource should no longer be.\ deductible in computing the income of the operator. .. I am proposing that. .. there be an extra abatement from federal income tax in respect of taxable production income.. .fifteen points in the case of mineral profits. .. "" - The Honourable John N. Turner, Minister of Finance. June 23, 1975-"" &apos;"" to meet, at least in part, the request for some form of deductibility in the tax system for provincial resource levies... to offer more incentive to those who explore and develop in Canada. .. I am now proposing, the extra fifteen point abatement of federal taxes would be withdrawn... at the same time, I am introducing a new resource allowance, which would be an extra deduction from income equal to 250/0 of production income.. ."" - The Honourable John N. Turner, Minister of Finance."

Jan 1, 1980

By C. McLachlan, J. R. Donald

"Positioned at the forefront of the seafloor minerals industry, DeepGreen Resources is on track to becoming a leading producer of base and strategic metals obtained from vast high-grade seafloor polymetallic nodule deposits. DeepGreen believes the seafloor minerals industry is an opportunity for developing a more environmentally and societally attractive way to produce cleaner base and strategic metals. Polymetallic nodules contain nickel, manganese, copper, cobalt and other base and strategic metals. Polymetallic nodules represent an exceptional multi-metal-bearing resource, and no current metallurgical operation or flowsheet exists that can recover the primary metallic values while managing the distinct mineralogy. DeepGreen Resources is developing a new process to maximize the business outcomes consistent with the highest environmental standards, including targeting a near zero waste facility. The present paper discusses the history, context and driving forces of polymetallic nodule project development. An overview of DeepGreen?s Nauru Ocean Resources Inc. (NORI) project is presented along with a literature review of polymetallic nodule processing and the on-shore project development scope and plan at DeepGreen Resources is outlined.INTRODUCTION AND CONTEXT Polymetallic Nodules in the Clarion-Clipperton Zone Containing nickel, cobalt, copper and manganese, polymetallic nodules occur in most oceans of the world. The nodules lie on the seafloor sediment. The largest deposit in terms of nodule abundance and metal concentration occurs in the Clarion-Clipperton Zone (CCZ) on vast abyssal plains at a depth of 4,000 to 6,000 metres. The CCZ is located almost entirely in international waters as presented in Figure 1. It has been estimated that the CCZ contains (International Seabed Authority, 2010): •,>21 billion tonnes of nodules; •,>270 million tonnes of nickel; •,>6 billion tonnes of manganese; •,>234 million tonnes of copper; •,>46 million tonnes of cobalt. There are several active hypotheses for the mechanism of formation of the nodules including precipitation, hydrothermal decomposition of basaltic debris, and involvement of microorganisms. Nodules require a nucleus to start forming, which could be a piece of pumice, a shark tooth, old nodule piece, basalt debris or even microfossils like radiolaria and foraminifera. Nodules form concentrically with layers of iron and manganese hydroxides around a core. Although composed mainly of Mn, Fe, silicates and hydroxides, it is the significant content of Ni, Cu, Co, Zn and Rare Earth Elements (REE) that is generating the economic interest in harvesting these deposits. Nodules vary in size from micro-nodules to about 20 cm, the common size being two to eight centimeters. A typical polymetallic nodule and polished cross-section is presented in Figure 2."

Jan 1, 2017

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By Owen Owens, W. P. Armstrong

The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors&apos; experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993