Search Documents

By Rolf Andreas Lauten, Yanhong Wang, Yongjun Peng

"In mineral flotation, bentonite as a kind of clay mineral imposes deleterious effects on the flotation of valuable minerals, possibly through its ability to increase the pulp viscosity. A higher viscosity lowers the amount of froth and affects the bubble-particle collision frequency. A previous study found that adding gypsum to a bentonite-ore mixture lowered the viscosity, possibly by inhibiting the formation of interconnected network structures. In this study, sulfate as an anion with different types of cations, Na+, K+, Mg2+ and Ca2+ were used to reduce bentonite viscosity and to improve flotation performance. It was found that at the same concentration, MgSO4 was the most effective salt in reducing bentonite suspension viscosity, while CaSO4 was not as effective likely due to the lower solubility of CaSO4. Na2SO4 and K2SO4 reduced bentonite suspension viscosity at high concentration. Flotation kinetics of ore blended with bentonite was increased with increasing the electrolytes concentration, which generally correlated with the reduction of bentonite viscosity. Meanwhile, significant discrepancies were found between flotation results and rheological measurements in the presence of monovalent ions. It is indicated that the morphology of bentonite aggregates in electrolytes solution is likely to influence the hydrodynamics in the froth zone.INTRODUCTIONClay is present in many ore bodies as a gangue mineral. Presence of clay presents several challenges in the processing of valuable minerals. They are soft compared to valuable minerals, which means that during grinding of the ore, clay particles are likely to obtain a smaller particle size than the valuable mineral. Often clay particles may be within the colloidal size domain (<20 µm). The smaller size increases the probability of entrainment in the concentrate. Another challenge is their anisotropic charge distribution, where depending upon the pH, edges (E) and faces (F) carry charges of opposite sign. This facilitates formation of aggregation structures that may impede percolation of bubbles through a froth, but also increase the viscosity more than expected from the mere change in volume fraction. In addition to lowering the froth mobility, a high slurry viscosity will have implications for the gas dispersion in the flotation column as it affects the dispersion of the suspended particles, and it modifies the bubble-particle collision rate and attachment efficiency (Bakker, Meyer, & Deglon, 2009; Shabalala, Harris, Leal Filho, & Deglon, 2011). A pragmatic approach to this problem is to blend high clay ore with ore of lower clay content, reducing the overall clay concentration. Alternatively, one may lower the solids content of the flotation slurry to counteract the viscosity-building properties of clay. While feasible, this approach has the disadvantage of increasing required flotation volume, and it also affects the properties of the froth. Thus, there are currently limited options in lowering the impact of clays and their tendencies to increase viscosity in flotation slurries."

Jan 1, 2016

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d&apos;asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l&apos;amiante peut offrir les performances souhaitées et l&apos;augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d&apos;une faible teneur en amiante courte il l&apos;enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C&apos;est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu&apos;on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991

By K. Shikaze

"For the last three years (1967-9) the value of the output of mineral resources in the Province of Ontario exceeded one billion dollars per year. To produce this great wealth, it was necessary for the mining industry in Ontario to dispose of an estimated 80 million tons of waste mill tailings. Some of these tailings were returned underground but the greater proportion was disposed of above ground in lakes, watercourses, marshy areas and in engineered impoundment basins. This volume of tailings, if accumulated in one location would cover an area of 1000 acres to a height of almost thirty feet. The provision of proper disposal of the waste mill tailings in a manner such that they will not create problems in the environment is one of the costs which must be borne from the extraction of such a wealth from our mineral resources. It is principally the potential water pollution which may occur as a result of the indiscriminate discharges of waste mill tailings which is of concern to the Ontario Water Resources Commission.ONTARIO WATER RESOURCES COMMISSIONThe Ontario Water Resources Commission was formed in 1956 and operates under the Ontario Water Resources Commission Act. The Act has been broadened and amended many times by amendments."

Jan 1, 1970

By Bill Charbonneau

Lumen, lm The measurement unit of light emitted by a light source 60W incandescent840 lumens 32W T8 linear fluorescent3200 lumens 54W T5HO linear fluorescent5000 lumens 400W metal halide24,000 lumens

Oct 1, 2010

By Ben D. Thompson

Cemented Paste Backfill has proven to be of critical importance to the operation of a number of Canadian mines, primarily due to the rapid backfilling rate this method permits. In order to improve the efficiency of this backfill system (i.e. optimize binder contents, fill fence design, and the employment of two stage filling strategies) there is a requirement to better understand its geomechanical behaviour. In response, in-situ experiments have been conducted in long-hole stopes to quantify the evolution of total earth pressures and pore pressures at a series of instrumented points within both the core of the backfill and close to fill fences. The deflection of fill fences as a result of paste loading has been measured and additional instrumentation has also been employed to measure cement hydration, negative pore pressures, and blasting induced vibrations within fresh and cured paste backfill. Installing geotechnical instrumentation within an open long-hole stope can be an extremely complex procedure and this paper details the methods that have been successfully employed. Preliminary results are presented, and the pressures induced by backfill with differing binder contents, at a number of different in-stope locations are considered.

May 1, 2009

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Apr 1, 2005

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985

By G. R. Yourt

"Generally speaking the usual approach for controlling dust is three-fold:1. Suppress the formation of dust at the source.2. Confine dust that cannot be suppressed.3. Dilute and remove dust that cannot be confined.This discussion will be concentrated on the second approach, namely, confining and disposing of dusty air.Dust BehaviourBefore delving into actual design principles a brief discussion on behaviour of dust should be helpful. For prevention of silicosis only respirable dust, ranging in size from < 0.5 to 5u needs to be controlled. As particles of this size have insignificant mass and momentum they follow air movements very closely. Consequently if contaminated air around dust sources is confined within enclosures and leakages maintained, strongly indraft dust is automatically controlled and capture velocities are of no concern.Dust SourcesAt metal mining operations ore is prepared for wet concentration by crushing it to mostly <3"" in size. This usually involves a jaw crusher, one or two cone crushers, one or more screens and several conveyors. Dust is actually produced only by the crushing action but it is liberated also when numerous fine particles contained in the ore stream are dispersed by surges and vibration at the discharge of the crushers, screens and headpulleys of conveyors. Furthermore, dust is dis¬persed when the slime adhering to the underside of the return portion of belts becomes dry and is rendered airborne by vibration and by cleaning floors especially where the slime has dropped."

Jan 1, 1971

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By A. Rodriguez-Prado

"Magnetic fields affect the growth of cultured cells and plants; however, limited information exists about their effects on vegetation performing environmental remediation. Constructed wetland mesocosms treating hexavalent chromium (Cr(VI)) wastewater exposed to low-intensity magnetic fields (60 Hz, 56.5 × 10-6 Tesla) produced 100% more biomass than the unexposed control. Nonetheless, they removed only 43 ± 27% of Cr(VI), compared to 60 ± 21% for the control. A Cr(VI) reduction expression was developed as a function of the magnetic field. The design and operation of constructed wetlands to treat mining wastewater can be corrected for magnetic field effects.RÉSUMÉ Les champs magnétiques affectent la croissance des cellules et des plantes cultivées; toutefois, il existe peu d’information quant à leurs effets sur la végétation utilisée à des fins d’assainissement environnementale. Les mésocosmes des marais artificiels traitant des eaux usées, contenant du chrome hexavalent (Cr(VI)), exposés à des champs magnétiques de faible intensité (60 Hz, 56,5 × 10-6 Tesla) ont produit 100 % plus de biomasse que le contrôle non exposé. Néanmoins, ils n’ont enlevé que 43 ± 27 % du Cr(VI), comparativement à 60 ± 21 % pour le contrôle. Une expression de réduction du Cr(VI) a été développée en tant que fonction du champ magnétique. La conception et l’exploitation de marais artificiels pour traiter les eaux usées des mines peuvent être adaptées pour tenir compte des effets des champs magnétiques."

Jan 1, 2015

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By J. M. Whatley

"IntroductionFEW COUNTRIES equal Canada in the diversity of its mineral output, the range of size of its mine operations, and the extremes of climatic and topographic conditions under which its mining is carried out. Camps large and small are scattered over thousands of miles, some served by excellent communication lines, many in remote regions of the north. Common to most of the deposits is that they are worked by underground methods, and rely on adequate hoisting installations for the success of their operations.Hoisting in some form •pre-dates all other mechanical operations in mines and the hoist remains one of the most important pieces of equipment at the average mine. It provides the single line of communication along which must pass the men and materials to mine the rock, and in turn carry the ore to a place for refinement.Development of Mine Hoists in CanadaCanadian designed hoists were first built and •placed in operation about the year 1880 and have since developed in pace with the rapid growth of the Canadian mining industry. Early machines were all of the steam or compressed-air driven types, of light construction and driven by two duplex slide-valve open-frame type engines. As their application and size increased, designs became more rugged and more efficient."

Jan 1, 1955

By P. R. A. Andrews, R. K. Collings

"SUMMARYIn cooperation with the Ontario Ministry of Natural Resources, selected deposits of Potsdam sandstone in the Ottawa-Kingston area were core-drilled and evaluated by CANMET as potential glass and foundry sand. Analyses of cores ranged from 84.6 to 98.5% Si02, 0.09 to 0.65% Fe203&apos; and 0.07 to 2.10% A12°3&apos; The cores were largely composed of white to grey, relatively tough sandstone. Impurities included iron as pyrite, iron oxides and staining on the quartz grains; carbonates as calcite; and aluminum oxide as feldspar. Beneficiation included size reduction to grain size, about 600 um, by jaw, roll and cone crushers, and grinding in a muller-mixer. Removal of fines was achieved by attrition scrubbing and washing. Further removal of impurities was achieved by reverse flotation of pyrite, iron oxide, feldspar, and carbonate minerals employing both anionic and cationic collectors. Flotation resulted in a substantial improvement in the quality of most samples; analyses of quartz concentrates showed 98.5 to 99.7% Sial> 0.022 to 0.156% Fe203&apos; and 0.07 to 0.62% A1203. Further reduction of the iron content by wet magnetic separation and acid leaching also was investigated. On the basis of the samples submitted, sands/ones from six of the seven deposits studied have potential as sources of glass sand. Foundry sand tests were inconclusive because of the small quantities available for study."

Jan 1, 1986

By Fazel G. Jahromi, Ahmad Ghahremaninezhad

Enargite (Cu3AsS4) is a major complex copper mineral and often is a carrier of invisible gold particles. Pyrometallurgical treatment of enargite is challenging due to the arsenic release to the environment. Hydrometallurgical treatment, on the other hand, appears to be a promising alternative for enargite processing. In an atmospheric enargite leaching process both the copper and arsenic from the mineral can be leached into a sulphuric acid solution and the arsenic can be simultaneously precipitated as ferric arsenate. The unlocked gold in the residue then can be recovered in a subsequent cyanidation circuit. The downside of the atmospheric enargite leaching in sulphate solutions is the slow leaching kinetics. In this study the effective parameters of the atmospheric enargite leaching process in ferric chloride media were investigated. All the experiments were carried out at temperatures below 100 °C. The process parameters that were investigated in this study included ferric, chloride, sulphate and cuprous concentrations, temperature, mixing rate and leaching slurry pulp density. It was found that the copper recovery rate increases with the addition of cupric chloride and also with raising the temperature. The highest leaching kinetics and the highest overall copper recoveries were achieved when cupric was initially added to the leach solution and at 90 ºC.

Jan 1, 2015

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By S. Ando

The fatigue crack growth behavior of magnesium single crystal has been investigated, CT (compact tension) type specimens with different notch orientations were prepared. In the case of notch plane and direction are (1-210) and [10-10], fatigue crack propagates parallel to notch, From TEM observation, it is found that pyramial slips occures at the crack tip. When notch is normal to basal plane, a fatigue crack propagates [0001] and parallel to basal plane depending on stress intensity factor range, In the case of notch parallel to basal plane, a fatigue crack propagates through straight route with some {10-12} twin, Fatigue crack growth rate, da/dN of A- and B- specimen is lower than F-specimen with crack parallel to basal plane.

Jan 1, 2004

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By A. P. E. Dirige

In order to maximize the recovery of ore in variably dipping ore zones of moderate width, cemented backfill is normally placed to serve as structural support. With the intention of saving on costs, backfill of low cement content can be used, which are often supported by a sillmat of higher strength. The stability of the low cement backfill face, exposed during adjacent mining, must be carefully studied to provide very effective, safe and economic mining operations. Improper design of these stope support structures may result in fill mass failure resulting in relaxation and failure of the stope walls, with consequent losses of production, ore dilution, and in safety problems. This paper presents a study conducted to assess fill performance during adjacent pillar mining and to provide a comprehensive understanding of backfill behaviour, the failure modes that may occur and the consequences to production, ore dilution and to safety problems, and accurately predict their stability. The design study investigated the effects of stope width and height, orebody geometry and inclination, and wall roughness on the stability of cemented backfill during adjacent pillar mining. Fill properties used were based on paste fill specimens cured for 28 days. Paste fill performances were assessed based on analytical and numerical modeling studies for the different mining conditions. Analytical modeling was carried out using limiting equilibrium analysis and numerical modeling was carried out using FLAC3D. The modeling results suggested that, for stopes that are inclined with smooth wall rock conditions, backfill failure, driven by the fill self-weight, has minimum dependency on the binder content and is reduced by resisting forces developed on the footwall-fill contact. For inclined stopes with rough wall rock conditions, wall roughness contributes significantly to the stability of the backfill during adjacent pillar mining. The analytical modeling approach was demonstrated to be useful in providing some approximate parameters for predicting the behaviour of paste fill exposed faces during adjacent mining, but cannot predict the mode or mechanisms of failure. Numerical modeling not only assess the stability behaviour of paste fill free faces, but also is able to provide a better idea of paste fill failure modes and possible failure mechanisms. The depth of failure and the potential for instability for a simulated stope filled with paste fill can be predicted, and may be useful in estimating the mass of material that could possibly fail and ore dilution levels.

May 1, 2009