Search Documents

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By William D. Gallant, Thomas M. Barczak, Carol Tasillo

"This paper describes the results of full-scale testing of several multi-layered wood crib configurations that were tested in the Bureau of Mines mine roof simulator in cooperation with the Cape Breton Coal Research Laboratory and Cape Breton Development Corporation of Sydney, Nova Scotia. Nine different crib configurations currently being used as wood packwall supports for advancing longwall applications in Canada were evaluated. Configuration parameters understudy included the aspect ratio (height-to-width relationship) and percentage of solid material used in the crib construction. Test results and generalized wood crib behaviour are discussed in detail. Recommendations are made concerning crib constructions to maximize strength and stability. A cost benefit analysis of multi-layered wood crib configurations is made. A comparison of laboratory results and underground observations of several wood packwall supports in the Sydney coalfield suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load bearing capability are described.IntroductionA cooperative effort was undertaken by the U.S. Bureau of Mines with the Cape Breton Development Corporation (CBDC) and the Cape Breton Coal Research Laboratory (CBCRL) to evaluate the behaviour of gateside packing materials used in advancing longwall mining applications in the Sydney coalfield. As part of this effort, full-scale tests were conducted on wood packwall supports in the Bureau's 3-million pound (13.3 MN) active load frame.Nine different pack configurations were evaluated as part of this study. The wood packwall supports were multi-layered crib constructions from 6 in. (0.15 m) by 6 in. (0.15 m) cross section timbers using timber s 30 in. (0.75 m) and 60 in. (1.5 m) in length . The percentage of solid material in the crib constructions varied as illustrated in Figures 1 and 2. A summary of crib constructions is provided in Table 1."

Jan 1, 1991

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By C. Harold Riches

This article is directed co a commentary on the patent system in its relation to the public interest. As man gained supremacy over his environment, he could devote progressively increasing portions o his time to improving his standards of living. In the history of the human race, we have advanced from the hollowed floating log to the modern steamship of the present age; from the sickle and flail to the reaper and combine; from the trumpet and drum as a means of communication co the telegraph, telephone, and radio; from the horse and ox cart to the automobile, truck, aeroplane, and train; and so on ad infinitum through the list of inventions on which are based the industrial and political economies and standards of living we enjoy today. It has also been a long road from the day of the alchemist and his closely guarded secrets to the era of the patent system and its storehouses of knowledge open to the world. The alchemist and the craft and merchant guilds closely guarded their secrets. In fact, they largely opposed innovations on the grounds that they might injure profits and restrict employment. In these days of unrest, with great clamour out of doors for radical changes in our political and industrial economies, it may not be untimely to examine one of the keystones which support the economic structure we know as the free enterprise system, the system which is predicated upon the right of the individual to own property. Many, through impractical idealism, ignorance, confused thinking, or blind political prejudice, advocate the substitution of ownership by the State ? for the right of ownership by the individual. As civilization has advanced to the high standards of living we enjoy today through the efforts of a comparatively few inventors, the patent system which has provided the incentive that created the inventions on which our industries and our employment are based is fully understood and appreciated by a comparatively small percentage of our people. As a result, the patent system, as a keystone in our free enterprise economy, is an apt target for destructive criticism, with the thought, possibly, that by eliminating or drastically restricting the several rights to individual ownership one by one, ownership by the State will progressively replace ownership by the individual.

Jan 1, 1949

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013

By B. Pewkliang, K. Ehrig, E. Macmillan, M. Smith, V. Liebezeit, Y. Li

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is the largest publicly declared uranium, fifth largest copper and third largest gold resource. Currently, the operation consists of an underground mine and integrated processing plant. Uranium is produced from leaching of flotation tailings and is a co-product to copper cathode with by-product gold and silver bullion. The Olympic Dam geometallurgy team began studying ore from the Southern Mine Area (SMA) in 2006 and soon discovered uranium behaviour was far more variable than the behaviour in the Northern Mine Area, which had been mined from the start of the operation in 1988. The primary objective of Olympic Dam geometallurgy is to develop metallurgical performance predictors that reliably describe the process performance of different ore types and distribute these into the resource block model for use as a fundamental input into mine planning. The nature of the uranium mineralisation (compositionally and texturally complex and highly variable) meant that classic mineralogy techniques alone could not provide the resolution required for prediction of uranium extraction. However, the combination of quantitative mineralogy, results from laboratory-scale leach tests and modelling within the geometallurgy program has enabled prediction of both uranium flotation recovery (via association with sulphides) and uranium leach extraction, including at variable leach conditions. These stope-based predictions have supported trade-off decisions between operating costs and uranium revenue, and have predicted the changing recovery as the mining operations have moved into the Southern Mine Area in recent years.

Jan 1, 2020

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By Dennis Martin

What is Borehole Hoisting Borehole Hoisting is the use of a hoisting plant to hoist rock, workers and materials or both, vertically through a borehole, between a mine level and surface or between two levels of an underground mine. Screen and bolt ground support on walls of 5.5 m diameter borehole hoisting shaft

May 1, 2013

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes' 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009

By D. Djokic

One of the most attractive features of electron beam curing as a process for manufacturing composite structures is the potential for attaining very low levels of residual stress as compared to thermal curing. This residual stress reduction is important both for the potential to reduce composite failure strains at low operating temperatures and the associated reduction in process-induced deformation. Previous work has demonstrated that it is possible in some cases to significantly reduce residual stress development during irradiation and also avoid development of additional residual stress during post cure. In this paper, simple L-shaped composite laminates were used to study the development of residual stress and deformation during thermal post-cure of specimens that were already partially cured using different radiation doses. Following post-cure, these specimens were also subjected to high-temperature loads to study creep behaviour under service conditions. Aerospace

Jan 1, 2006

By Lisa J. Renaud

For generations, the mining industry has been committed to work toward developing new technology that can improve safety and increase production. Now with a more environmentally conscious society and tighter environmental regulations, a natural progression for the industry is to develop and take-on ?green? or environmentally friendly technologies. Not only could this improve the sustainability of operations, but could also reduce the long-term environmental impact footprint that is left behind. Algae represent a new frontier in research and development. As discussed specifically in this paper, algae, specifically microalgae, can be used for the production of biodiesel and other green chemicals by exploiting carbon dioxide and waste heat contained within process off-gasses. The potential positive benefits of this approach in terms of contribution to community and the environment are significant, and the focus of our research and development on microalgae production technology.

Oct 1, 2010

By Donald S. Cameron

By dispersing gold in high surface area form supported on metal oxides, its inert character can be transformed to make economical, effective catalysts. Gold has already been demonstrated in a number of fuel cell applications such as gas phase catalysts, electro-catalysts, and electrical connectors. In this paper, the various types of fuel cell systems are reviewed, and several opportunities for gold identified. Low temperature fuel cells, including alkaline and solid polymer electrolyte types rely on high surface area platinum group metal catalysts which are highly susceptible to poisoning by low concentrations of carbon monoxide in the fuel supply. Hydrogen is frequently obtained by steam reforming hydrocarbons, followed by the water gas shift (WGS) reaction. A promising initial use for supported gold catalysts is in catalysing this WGS reaction. Research has shown that gold supported on iron oxide (Au/a-Fe2O3 ) WGS catalysts are more active than the current commercial copper oxide / zinc oxide catalysts, and effective at temperatures as low as 120oC. Products from reformer/ water gas shift reactors can be further purified by removing traces of carbon monoxide. If a small proportion of oxygen is introduced into the fuel gas stream, carbon monoxide can be preferentially oxidized to carbon dioxide even in the presence of hydrogen. Gold nanoparticle catalysts on iron oxide support (Au/a-Fe2O3 ) have exhibited higher activity than commercially available platinum on alumina (Pt/?- Al2O3 ) preferential oxidation catalysts. The low temperature of this reaction may make it feasible to incorporate these catalysts within the fuel cell itself. Proton exchange fuel cells provide several possible applications for catalytically active gold and its alloys. Carbon supported platinum group metals would benefit greatly from improved electrical conductivity if gold replaced some or all of the carbon support material. As electrode current densities are raised, electrical resistance constitutes an increasing proportion of voltage losses within the fuel cell. Dramatic reductions in cell stack voltage losses have already been demonstrated by reducing inter-cell contact resistance using gold plating. The low temperature oxidation properties of gold catalysts have been investigated in controlling gaseous emissions from direct methanol fuel cells, and gold also provides essential catalysis in building direct borohydride oxidation fuel cells. The prospect of a range of other applications for gold in fuel cells to contribute useful improvements in corrosion resistance and conductivity is assessed. Globally, fuel cells have been developed for a wide range of applications including stationary generators, cars and buses, industrial vehicles and small portable power supplies, each of which represents a substantial market. Hence there are likely to be many and varied opportunities for gold catalysts to contribute to the performance and economics of the systems being commercialized.

Oct 1, 2003

By Neil Schofield

"The Pine Creek gold mineralization is associated with saddle reefs and quartz and quartz sulphide veining within the Enterprise Anticline. The anticlinal structure is complex and the mineralization was considered prior to development to be dominantly strata controlled. Gold grades vary up to 160 gin 1.5 m core samples with coefficients of variation in excess of three.The estimation of ore reserves for such a deposit must account for both the geological complexity and the extreme variability of gold grade.This paper describes the structural and variogram analysis of the gold grades and demonstrates the importance of incorporating the geological model in such an analysis. Variogram interpretation is greatly improved and greater insights into the finer geological structure areprovided. Part 2ofthis work presents the application of multigaussian kriging to reserve estimation for deposits with highly variable grade and which consequently demand highly selective mining operations. IntroductionThe Enterprise Gold Mine is situated some 220 km southeast of Darwin in Australia's tropical north. Gold is believed to have been discovered there in 1869 during the construction of the overland telegraph line.From 1894to 1915, some 75 000 ounces of gold were produced from 121 000 tonnes mined mainly by Chinese leaseholders. From 1906 to 1915, government-sponsored drilling led to the sinking of the Enterprise Shaft to 79 m and several drives were developed. Mining ceased because of war.Since late 1980, Goldfields Exploration Pty. Ltd. had explored on several mining tenements near Pine Creek under joint venture with the title holders, Enterprise Mines NL. This work culminated in the development of the current mine which opened on October 29, 1985.Feasibility studies to determine the economic viability of mining were based on ore reserves generated by project geologists using a sectional polygonal approach tuned to the interpreted geological control of the mineralization.The study motivating this two-part paper covers are-estimation of the recoverable reserve s using the geostatistical approach of multigaussian kriging developed at Stanford University, (Verly, 1984)."

Jan 1, 1988

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

Magnetic separation of precipitated magnetite as iron resources in copper slag is one of the potential effective ways to recycle the slag. It is preferable to convert molten fayalite slag after copper smelting process to magnetite slag via oxidation. With a TTT (Time-Temperature-Transformation) diagram, the crystal composition of the slag obtained after air isothermal oxidation could be estimated through a designed cooling path. The crystallization behaviors concerned with molten oxidation was studied for better understanding of the trade-off relationship between magnetite and hematite during molten heat treatment. Moreover, a brief consideration was implemented of the reaction mechanism.

Jan 1, 2014

By G. K. Rutherford, G. W. Van Loon

"Tailings in the mining and smelting industry are reject products of the refining process which are deemed too deficient in native are to warrant smelting. They are essentially finely ground rock materials which have been moved by alluvial suspension from the site of crushing to a deposit site. It is realized that components of flotation chemicals used in specific gravity separation may become part of the tailings and also that sewage sludge or other materials may be added at some stage to the tailing deposits.It would seem, then, that as tailings have a similar parent material to soils, namely rocks, and that they have also been comminuted to similar size fractions, they would react in similar ways to soils. There is an increasing body of evidence and experience which both supports and negates this supposition. It is the object of this paper to point out similarities and contrasts between these two materials which may influence the vegetation and rehabilitation of tailings.Soil-Formlnq FactorsThere are considered to be six soil-forming factors which impart the particular and unique properties harboured by a soil at any site. It is .relevant to consider each of these in turn, as each provides an historically based parameter with which to judge tailing properties.Parent MaterialsAlthough all mineral soils have originally come from rocks, for most soils the route has been rather circuitous. Soils may be formed directly from underlying rocks, as in some parts of tropical and semitropical regions today; these are sedentary soils. However, most soils of the world have been formed by materials which were transported to their present site by ice, water or wind, or as volcanic ash. Virtually all soils in Canada have been transported by ice or water and deposited on an extraneous rock surface during the last glacial retreat. Ice-deposited materials are extraordinarily heterogeneous in their size components and may range from very bouldery and gravelly to predominantly clay-sized materials. Water deposited sediments are usually homogeneous, but nevertheless these also show considerable level variations. In many parts of Canada, clay-sized materials deposited in ephemeral post-glacial lakes form the parent material for soils."

Jan 1, 1982

By Mauro Chiesa

An Overview on the Presentation A.The Markets ?Mining Industry ?Capital Markets ?A Six-Cell Matrix of Strategic Options B.De-Risking The Mining Assets ?The Value-Added ?The Assets: Current and in Development ?The Feasibility Study C.(Questions, and answers) Post-Crunch: Some Maxims ?Three Metal Market Models No Longer Prevail ?New models are uncharted: ?be prepared?(ref: Lord B-Powell). ?Capital markets are pricey & uncertain: be your own financier first ?focus on value and on cash-flow (not oz, lbs, tonnes, LOMs, etc) ?Know your banker/financier(and it should know mining) ?In the past, it was ?know your borrower? ?It?s a buyer?s market that wants the ?right deal?: so cast a big net: ?Data must be current, concise and consistent ?3rdparty validation of feasibility work is now a ?passport? ?The risk matrix, with de-risking, is as important as the ?math?

May 1, 2011