Search Documents

By R. H. Keyes Duval

"The one point left off the table was pumping costs, i.e. the cost of pumping to the cyclones.At East Malartic 5 x 5 S R L pumps that had been used to pump the classifier overflow were used to pump the rod and ball mill discharges to the cyclones. Maintenance costs on the pumps rose from $105 in 6 months to $1000 per month. The pumps had to be operated at 1150 rpm and impellers lasted only 5 to 6 days. These pumps were replaced by 6 x 6 S R. L. pumps operating at 825 rpm, but at this speed the coarser sands settled and plugged the pipe lines and the speed was increased to 925 rpm. The maintenance cost is now $100 per m::rnth which is 0 003 cents per ton milled. The impellers now last 1 month and the casing linings 6 months.Density meters are often used on cyclone overflows and sometimes on the cyclone feed. Haliburton weighted tube density meters are used in some plants. They are cheaper than the radioactive density controller, $2500 as compared to $ 6000The angle of the discharge spray from the apex can be used to judge the quality of perform1nce of a cyclone.For ordinary metallurgical applications the inside slope of the cyclone is not too important but for fine separation steeper slopes are used.The cyclone is a versatile tool and will handle considerable variations in feed tonnage - probably up to 15%. Above this variation the number of cyclones used has to be increased or decreased or the tonnage fed to them has to be adjusted"

Jan 1, 1965

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By Elma van der Lingen

Gold is considered the most inert of all metallic elements, but the metal can show catalytic activity when prepared by specific techniques. Preparation techniques being used to prepare gold catalysts systems mainly involve precipitation methods incorporating gold compounds or complexes. This paper introduces a totally different method for the preparation of gold-based heterogeneous catalysts that can be used for oxidation and reduction reactions, as well as electrocatalysts. The method involves alloying of gold with a less noble metal, such as aluminium, to form a gold-containing intermetallic precursor. AuAl2 was produced by melting gold and aluminium together in a vacuum arc furnace under a protective atmosphere. The aluminium is then dissolved from the AuAl2 precursor by means of NaOH to produce a highly porous gold structure. The paper also reports on a method of incorporating transition metal oxide(s) with the porous gold to form an active heterogeneous catalyst. Promoter elements can also be melted with AuAl2 to improve catalytic activity. Alloying has the advantage that the promoter element can be in contact on atomic level with the gold. In-situ xray photoelectron spectroscopy (XPS) studies have also been done on the porous gold catalysts to further clarify the CO oxidation mechanism on gold-based catalysts.

Oct 1, 2003

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By Candido Bariáin

A new vapochromic material of formula [Au2Ag2(C6F5)4(bipy)2]n (bipy = 2,2´ bipyridine) has been developed and used for the detection of some volatile organic compounds as acetone either in vapour or in water solution. The material is presented in the form of powders which colour changes with acetone vapours turning from bright yellow in the absence of vapour to white in the presence of vapour. By using the sol-gel technique, the powder ? dispersed in tetraethyl orthosilicate- was easily deposited on optical fibres. In order to study experimentally the behaviour of this material for construction practical optical fibre sensors, a sol-gel material doped with the vapochromic material is deposited onto an extreme of a monomode fibre connected to a coupler. The behaviour of the material was studied for different wavelengths and concentrations of acetone vapours and acetone/water solutions. Changes up to 4dB in the reflected optical power were detected. Optical fibre sensors have many advantages over conventional ones, such as electromagnetic interference immunity, passivity behaviour, possibility of using multiplexation techniques, low weigh and little size, etc. Actually, there is an increasing interest in developing optical fibre sensor for vapour detection in the chemical industry and in fact many sensor had been developed [1]. Some are based on the deposition of a sol-gel-based material either over the core of an optical fibre [1] or onto the thinner zone of a biconically tapered optical fibre [2]. Others are based on Fabry-Perot interferometers [3]. Also there are sensors based on the reflection of the light on films, on the fluorescence of dye-doped polymer cladding in fibre, on colorimetric reagents in the core of a silica fibre or on surface plasmon [4]. The possible materials for the construction of such sensor should be colorimetric reagents able to change the colour or refractive index in the presence of same organic vapours. There are not many metallic complexes with these properties, although same interesting examples have been reported in the chemistry of palladium and platinum as [Pt(p-R-C6H4NC)4][Pd(CN)4] described by Nagel [5] and Mann [6], which reported the construction of some LEDs. We recently reported the preparation of a novel vapochromic material (Fig 1) [7] which can be used for the construction of optical fibre tapered environmental sensors [8,9] of vapour organic compounds (VOC´s). Also we reported other nickel and palladium derivatives which present this type of behaviour [10]

Oct 1, 2003

By J. Kalynchuk, R. Poulin, R. Pakalnis, D. Peterson

"A market survey of all underground mines in Canada (Fig. 1) was completed to determine the ex1ent to which cable bolts are being used as ground support. One hundred and nine questionnaires were distributed with 65% of them being returned completed. As a result, the quantity, types and locations of cable bolt installations have been determined. In addition, the grout pumps used, time required and cost of installations have been addressed. The popularity of other support types used in underground mines is summarized.IntroductionRock reinforcement consists of installing support within the rock mass (internal) or within the excavation (external). Within the past twenty-five years several new types of ground support have been introduced within the mining industry. Cable bolts were first introduced to the Canadian mining industry in the 19605 (Gramoli, 1975).Cable bolts have gained increased acceptance as a method of ground support during the past decade. The cable bolt is comprised of one central wire surrounded by six slightly smaller outside wires and typically having an over-all diameter of 15.2 nun to 15.9 nun (0.6 in. to 0.625 in.). The cable wires are made from high-strength steel with an ultimate strength of 26 tonnes (58 000 Ibs) (Goris, 1990). Current cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to reinforce the surrounding rock mass. Cable bolts are a form of internal support and are generally used in open stoping and cut-and-fill mining methods (Fig. 2).They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, they are generally less than 20 m (65.5 ft) and are untensioned. A major advantage compared to previously used ground support is that the cables are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils allowing relatively long support to be installed in areas with limited head room (1.8 m).With the advent of bulk mining methods which require comparatively large stopes, it has necessitated the use of relatively long support tendons to stabilize the large spans being created. As a result, the use of cable bolts for ground support in mines has increased significantly within the past decade."

Jan 1, 1995

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By George Dogbe

Open pit optimization forms the basis of mine design, production planning and construction of mine facilities. The negative effects of this phase may include substantial reductions in ore recoveries, relocation of waste dumps and surface infrastructure, extraction of unwanted waste, with a cumulative effect on mine value reductions. As a result, this area has received significant research focus using linear and dynamic programming, heuristic, genetic and stimulation algorithms and the graph theory. These algorithms are derived from rigorous mathematical models, but they are built on the assumption that all the periodic production capacities are extracted at the time of analysis. This assumption weakens the models because mining occurs over significant time period. In order to develop a comprehensive model that accounts for the timing of material extraction, the current models, which are built on the economic block value (EBV) concept, must be modified to account for time. In this paper, the authors develop a model of the optimization problem using the 2-D Lerchs-Grossmann?s optimization algorithm. This model is used to investigate the effect of periodic discounting on the optimal pit layout design by designing an integrated pit optimiser (IPO) that incorporates ?production scheduling?. IPO uses the ensuing discounted economic block value (DEBV) as a basis for the pit optimisation process. The time-dependent model is compared with a time-independent model. The results show that discounting has no effect on the optimal pit contour although the reported pit value is overstated if the EBVs are used instead of the DEBV. The authors, however, believe that this conclusion may not be general and could have been influenced by the nature of ore body geometry and the proposed mining strategy.

May 1, 2004

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

By E. Haccuria

Due to the growing share of electrical cars, the use of lithium ion batteries significantly increased. Recycling of these batteries is essential to safely dispose hazardous materials as well as to recover valuables (Cu, Ni, Co, etc.). In order to optimise the recycling process, accurate information is required on the slag phase equilibria for battery smelting. The slag is a multi-component system containing alumina from the battery cases, silica and lime from fluxes, and manganese and lithium from the electrode materials. The present study accurately determined the phase equilibria in the "MnO"-Al2O3-SiO2 sub-ternary system at metal alloy saturation. Particular attention was given to the accuracy and reliability of the final results by highlighting the different reaction pathways, mass transfer- and reaction mechanisms taking place in the system during experiments. This attention enabled improved experimental methodology and measurements. Based on the present study, further measurements will be undertaken in the quaternary "MnO"-Al2O3-CaO-SiO2 system at low "MnO" concentrations, which closely represents the future recycling industrial slags.

Jan 1, 2014

By R. Harris

The vacuum thermal route for magnesium production today accounts for roughly 80% of the global production of magnesium despite significant investment in the competing electrolytic technologies, This is up from 30% of the global production 10 years ago and is all the more significant because global magnesium production has more than doubled in the same time, A review of the sophisticated anhydrous magnesium chloride production technologies provides some explanation for this sea change in technology usage, However, an examination of the economic factors provides compelling reasons, The present review outlines some of the salient strengths and weaknesses of the competing technologies, It also offers suggestion as to where future R and D and economic effort needs to be vested to improve the sustainability of the world magnesium market in terms of its value and impact.

Jan 1, 2006

By Roger Lacroix

Fuel cell application to mining has been indicated to be potentially beneficial to underground mine worker health and to energy efficiency. In order to define the economic advantages of using hydrogen fuel cell vehicles, a detailed study of operating and capital costs associated with underground loaders and power supply infrastructure has been carried out. The results show that for a typical medium-size mine, operating costs and infrastructure costs are less for the fuel cell option versus diesel. The reverse occurs for capital costs owing to the currently higher cost of fuels cells versus diesel engines. This disparity is expected to decrease given the decline in price associated with fuel cell technology advances. Related market issues for fuel cell manufacturers are also presented. Despite the difference in cost, the resources and mine infrastructure required to operate loaders, and base design of the mine loader, is similar for diesel and fuel call versions.

May 1, 2007

By Hung-wei Liu, Kevin Plucknett

Early attempts to manufacture titanium aluminides using blended elemental powders, through powder metallurgical processes, have been obstructed due to serious swelling during sintering. Although the use of pre-alloyed powder can avoid this undesired expansion problem, there are limited commercial powder sources available. Therefore, in the present research, fundamental studies on the synthesis of dual-phase (? plus a2) Ti48Al intermetallic materials is undertaken, in particular assessing powder manufacture. In order to produce pre-alloyed powders, highly porous Ti48Al pieces are initially sintered from elemental Ti and Al powder blends, and subsequently pulverised into powders. The powder size is then further reduced by use of either dry or wet milling processes (i.e. shatterbox grinding, attrition, or ball milling). Among these methods, shatterbox grinding has shown the highest efficiency, with a slight mechanical alloying effect observed. The manufactured powder morphologies and phases, as well the sintered material, will be discussed.

Jan 1, 2015

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

By W. Hrynewich

"The Central Canada Potash facility, a division of Noranda Metal Industries Limited, is located 3 kilometres south of the junction of Highways 16 and 2, about 75 kilometres south-east of Saskatoon, Saskatchewan. The site occupies 26~ hectares of land and includes well-equipped machine and electrical _shops, a 325,000-tonne muriate storage and reclaim warehouse, a stores warehouse, processing plant (mill), two mine shafts (one for production, the other for servicing and personnel transport), as well as a two track product loading complex. Access to the site is by road and railway (CN and CP Rail). Suppliers of operating and maintenance use both means of transportation, whereas muriate shipments are entirely by railway.Currently five continuous mining machines - one a Goodman 526 borer and four Marietta 911-A units produce some 10,500 tonnes of ore per operating day. A smaller Voest-Alpine Af.1-100 boom type miner is used for floor cutting which was previously done by a production unit. In order to maintain safe, competent ground conditions only 35 percent of the total ore is extracted. At this rate mine reserves are deemed adequate for about 100 years. The plant has operated since August 1969 and has a current practical annual capacity of 1,270,000 tonnes of muriate. As of June 30, 1981, some 11.9 million tonnes of muriate had been produced from 31.4 million tonnes of ore. Of the total muriate, 6.1 million tonnes was granular, 4.8 million was coarse, and 1.0 million was standard. No standard product has been made since August 1978."

Jan 1, 1982

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

By Michael J. Sapko, Ellsworth R. Spencer, Frank J. Perzak

"The fire resistance of several mine conveyor belts is evaluated using a new belt-flammability apparatus developed by the U.S. Bureau of Mines. The test apparatus, experimental details and a calculated flammability index (FI) are described.The FI values are useful for ranking the fir e resistance of mine conveyor belts. Values are determined using parameters readily measured with thermocouples, high-temperature flow probes and a methane-oxygen torch, all of which are components of the Bureau's new test apparatus. The FI varies directly with the flame-spread rate and the rate of heat release during burning and varies inversely with the critical (minimum) ignitor energy output.The fire-resistance ranking of nine different belt types using this moderately scaled apparatus is compared with available full-scale data on belt fires. This comparison shows that the ranking based on the FI is consistent with the full-scale data.IntroductionFull-scale fire hazard evaluations of mine conveyor belts are not easily related to the properties usually measured in small-scale flammability tests. The inadequacy of small-scale belt fire tests has been demonstrated in works by Mitchell, Warner and Reinke.Mitchell and Warner showed that certain neoprene (NP) and polyvinyl chloride (PVC) belts, which had been approved by the Code of Federal Regulations 30 CFR 18.65, were nevertheless capable of propagating flame over their entire length when full-scale fire conditions were simulated. Comparable results were also observed by Reinke at the Tremonia experimental mine in Dortmund, West Germany, where all belts burned in full-scale tests even though they passed the small-scale tests. Only by reducing the severity of the full-scale test could these fire-resistant belts be grouped on a pass-fail basis."

Jan 1, 1982

By Bing Li, Kai Liu, Yongcheng. Zhao

With the ongoing development of copper smelting technology, the improvement of environmental emission control and achieving an automated continuous copper pyrometallurgical process have become the key development goals for copper smelting. The double bottom blowing continuous copper smelting process combine bottom blowing smelting (SKS) and bottom blowing converting (BCC) process and fire refining as “three-connected furnaces” arrangement is a pyrometallurgical process independently developed by China’s ENFI which can continuously produce copper from raw material through to anodes. This technology can improve energy efficiency and reduce environmental emissions for the overall copper smelting and converting process. This paper discusses the engineering characteristics and production practice of the SDIC Jincheng Metallurgical Project, which operates SKS smelting and BCC converting process with “three-connected furnace” arrangement for the first time in the world. Advanced engineering concepts and tools were used to optimize the configuration during the project engineering stage. The operation shows that the process has good environmental performance, reduced energy consumption and high level of automation, which is a new choice for copper continuous smelting process. INTRODUCTION One of the most important developing trends for the overall copper smelting process is to develop a continuous operation. Continuous copper smelting can maximise energy efficiency in copper concentrate and make full use of the rich heat treatment system. Cold charge and a part of low-heat-generating materials, which are processing with additional equipment in traditional copper smelting process, can be processed with rich reaction heat in continuous copper smelting and converting process to achieve good economic benefits. Yuan and Wang (2017) noted that SKS+BCC copper smelting process can reduce the secondary SO2 emissions compared with discontinuous copper smelting process, which required transportation of melted matte by matte ladle and may cause secondary pollution. The continuous copper smelting process can also reduce the generation of intermediate cold materials.

Jan 1, 2019

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By Carl Sonnen

Reading the newspapers, you will know that opposition to ratification on economic grounds always points to the view that action will result in major price increases for energy (to both industry and households) with consequent severe losses of energy production and a loss of competitiveness for energy-intensive producers (i.e., in your kinds of industries). You might think of this as the ?carbon tax? fear, and you should note that many of the initial policy development experiments included variations of this theme. Analysis reported in late 2000 and into early 2002 reported reductions in energy production in the long run of between 10% and 20%. At the upper end of that view, these were the kinds of numbers reported in the Industry Canada study ?leaked? to the Press last week. The consequences of this approach included significantly uneven negative effects for some provinces (e.g., Alberta, but also Saskatchewan and Newfoundland). It had been agreed by the First Ministers of Canada, however, that the policy should not yield those results so development in recent months has focused on eliminating sector and therefore provincial ?sore thumbs?. Although an emissions trading system, which represents this type of approach and directly impacts costs of production, continues to be featured in the new or current policy and is applied to the Minerals Industries among others, it is designed to be implemented in such fashion that the costs are more moderate than before. And because the industries covered by permits are almost all price takers, there is no device for moving an increased price signal forward to ?consumers?. What this does do is even out negative effects among sectors in the economy and for provinces, but at the expense of government financial results.

Nov 1, 2002