Search Documents

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By J. W. Hendry

"This paper will discuss the application of tools and the evolution of computer-assisted procedures in the production planning process at Quintett e Coal Limited (QCL). In 1986, QCL produced 5.3 Mt of clean coal from their surface mining operation located in north eastern British Columbia. The structural complexity of the sedimentary deposit and high rate of mining necessitate the consideration of large amounts of geological information which continually updates the interpretation. There are multiple unit operations required during the process of mining through a given multi-seam sequence, which results in many interdependent faces, and multiple iterations of scheduling sequences in order to satisfy a given set of objectives. In order to facilitate these activities in a timely fashion, it was recognized that a computer systems' capability needed to be developed which could increase the efficiency of information input, manipulation and output. IntroductionQuintette Coal Limited (QCL) has been operating a large metallurgical open pit coal mine in northeastern British Columbia, since 1982. The mine produced 5.3 Mt of clean coal in 1986 for export to Japan. Throughout the start-up period and the subsequent build -up of production levels, it became evident that the primary producing area was comprised of extremely complex faulted structures. This has resulted in development and modification of specialized mining methods employed to effectively recover the resource. Similarly, the planning and engineering techniques employed have been evolved over the same period of time. The implementation of computerized methods has been one of the major developments in this process, including geology interpretation, modelling, reserve definition, quantification, production planning and scheduling, and graphical plan presentation. These capabilities have been employed, in various forms, for project scale feasibility work and long range planning for some time, however, the use of computer tools for short-term, detailed production planning of a complex mining environment presents a different set of problems. It is hoped that a presentation of the current state of evolution and future plan s for development will be of interest to organizations considering implementation of a similar system."

Jan 1, 1988

By N. K. Jaber

The "Pidgeon Process" for the extraction of magnesium from dolomite ore utilizing ferrosilicon as the reducing agent has been studied extensively by active metallurgists such Mr L,M, Pidgeon the father of this process, Most of the work sited so far has focused on heating the (FeSi/MgO,CaO) briquette mix under vacuum in stainless steel retorts by external fuel hydrocarbon heating, In this work Electrical Induction Heating was employed as the heating method whereby the briquette mix was placed in a steel crucible around which an Induction Heating copper coil was wound and placed inside in a stainless steel vacuum tank, It was observed that by virtue of the fast Induction Heating method utilized in the silicothermic extraction process higher reduction temperatures were reached in shorter periods of time due to fast heat transport into the ore charge mix, This facilitated shorter metal reduction times as compared to the conventional fuel heating methods.

Jan 1, 2006

By J. L. Blaylock

Normally, the hydraulic system and structures are considered to be unrelated items. In reality, the two cannot be separated because one affects and depends on the other to function properly. This paper explores the potential failure areas of hydraulic cylinders, and suggests possible methods to prevent failures from occurring. The use of high-strength low-alloy steel in frames is reviewed and the benefits discussed. Fabrication techniques and handling of material are noted in the hope that this knowledge will aid in the repair of frames in the field.

Jan 1, 1979

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By Corby G. Anderson

"Laboratory testing using industrial electrowinning solutions was performed to determine the best Faradic cell efficiency for copper cathode recovery. The variables tested were solution flow rate, recycle ratio, reagent addition combinations of guar and thiourea, and addition amount of acid mist suppressant CAL FAX DBA-70. The ideal flow rate was determined to be 37.85 litre/min. Additionally, the ideal recycle ratio was determined to be 10:1. The reagent addition scheme from testing which showed the highest efficiency was with 680 g/tonne guar of cathode copper won and with 135 g/tonne thiourea of cathode copper won. These values for reagent addition only reflect the best efficiency and should not be assumed to be the best reagent concentration for copper purity. The amount of foaming agent that showed the best efficiency was the test with 2 ppm of foaming agent. Again this amount of reagent is based on efficiency and should not be taken as the amount of reagent that does the best acid mist suppression. Additional proprietary surface characterization work indicates these additives may have enhanced the cathodic reduction surface morphology of some noble minor impurities. Subsequently, these operating parameters were introduced into the plant operation and proved successful after their implementation.BACKGROUNDCopper electrowinning has become a dominant technology for the production of marketable high grade copper cathode products. The literature is robust with applications, optimizations, additives and developments in this field (e.g., Classens & Harris, 1990; Pfalzgraff, 1999; Tozawa, Su, & Umetsu, 2003; San Martin, Otero, & Cruz, 2005; Houlachi, Edwards, & Robinson, 2007; Romero, Avila, Fester, & Yacher, 2007; Marsden, 2008; Beukes & Badenhorst, 2009; Vainio & Weatherseed 2009; Bender, 2010; Joy, Staley, Moats, Perkins, Uhrie, & Robinson, 2010; Khouraibchia & Moats, 2010; Moats, 2010; Rutledge & Anderson, 2015).Tests of forty hours duration and at room temperature were performed for this project using samples of actual industrial electrowinning solutions. These industrial solutions were comprised of 60 g/L Cu plus 65 g/L Ni, 3 g/L Fe, and 30 g/L free sulfuric acid. Other confidential minor impurities were also present including some solubilized precious metals. The testing apparatus utilizing stainless steel anodes and cathodes is illustrated in Figures 1 and 2."

Jan 1, 2016

By M. Lghoul

Acid mine drainage (AMD) remains one of the major environmental problems for the mining industry particularly for many abandoned mine sites. The production of AMD as is commonly known can significantly affect the surrounding groundwater and surface water of the mine site. With the objective to investigate the impact of the AMD produced at the abandoned Kettara mine site (Morocco), groundwater sampling campaign was performed at this site. The sampled waters were analyzed to determine the hydrogeochemical composition, and then results were analyzed using different studied methods such as multivariate statistical analysis and geochemical modeling techniques. Investigation results show that the hydrochemistry of sampled waters is characterized by the relatively significant enrichment of Ca2+, Mg2+ and SO4 2-. The typical mine waters belong to the (Ca2+ +Mg2+)-SO4 2-type. Seasonal variations in major ion concentrations were partly attributed to dissolution/ precipitation processes. The saturation index (SI) calculation of the representative dissolved minerals in waters show that groundwater samples are undersaturated with respect to most potential sulphated secondary minerals.

Aug 1, 2013

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment's usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By S. Kashani-Nejad

The kinetics of the thermal decomposition of samples of Mg2(OH)3Cl.2H2O that were obtained by a novel leaching technique applied to a commercial magnesium electrolysis feed were investigated under ambient atmosphere. Thermogravimetric (TG) Analysis showed that decomposition of Mg2(OH)3Cl.2H2O exhibited a single intermediate stage wherein crystalline water was lost at roughly 108 °C. Conversion of the resulting Mg2(OH)3Cl to MgO, HCl and 1120 occurred at temperatures above 398 °C. Thermal decomposition of anhydrous Mg2(OH)3Cl was seen to be consist of two stages. Both stages exhibit first order kinetics with respect to the weight percent of Mg2(OH)3Cl remaining in the sample. However, the rates of decomposition in the two stages were significantly different. Detailed analysis of the kinetic data suggested that the rate of decomposition of Mg2(OH)3C1 was controlled by the rate of removal of the gases released. The change in decomposition rate during the course of the experiments was explained by HCI being released in stage 1 and followed by release of H2O in stage 2.

Jan 1, 2004

By D. J. MacDonald

UNDERGROUND development at the Lynn Lake property of Sherritt Gordon Mines, Limited, was begun in 1948 with the sinking of the A shaft in the area of the A orebody. By June, 1949, the shaft was completed to a depth of 1,024 feet. Twelve stations were cut, with the bottom level at 992 feet below the collar. Since completion of the shaft, lateral work has been carried out on the 12th level in order to expose the known orebodies and to provide openings from which deeper exploration could be conducted. Dur¬ing the change-over from sinking to lateral work, preliminary diamond drilling was done from the 12th level station to locate the A? ore-body. Later, drilling was carried out from the 5th and 9th level sta-tions, where, also, the outline of the A orebody was established. As the work progressed on the 12th level, and with the commence-ment of drilling below that level, the geological picture was found to be complicated by numerous faults. Instead of operating two drills it became necessary to use at least four. The original plans had provided air sufficient to drive two headings and to operate two diamond drills. The addition of two more air-driven drills resulted in a serious shortage of power.

Jan 1, 1951

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By Raymond S. Suglo

Increasing depths of mining coupled with the mechanization of most underground mining operations have led to growing complexities in the mine environments with the production of large amounts of gaseous and particulate contaminants. Over 100,000 lives have been lost due methane gas and dust explosions in coal mine workings in both the US and Canada since 1900 when the methane concentrations exceeded stipulated levels in some workings. There is therefore the need to constantly assess and evaluate the performance of the existing mine ventilation systems to maintain safe and acceptable mine environmental conditions in workings to meet the requirements of federal, state or provincial laws. This paper uses the results of continuous monitoring of methane concentrations conducted in selected development headings in coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems in the control of methane gas concentrations in the headings. The results show that the average quantities of fresh air required to dilute, disperse and remove methane concentrations within set levels of one minute varied from 5.43 m3/s in Heading #11 (Condition 2) to 27.97 m3/s in Heading #10 (Condition 1) and this represented about 12 to 26% of the quantities required to dilute methane concentrations to safe levels within one minute under Condition 1 and 32 to 139% under Condition 2. The average dilution times in the headings studied were less than 8 minutes. The forcing efficiencies of the auxiliary systems in the headings studied ranged from poor to excellent implying that the auxiliary ventilation systems were capable of controlling the methane concentrations below statutory levels but may not be able to cope with large and unusual methane concentrations in the headings. This study is important to prevent methane gas and coal dust explosions in coal mines and thus avoid any loss of lives and property.

May 1, 2001

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955