Search Documents

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By Walter Valery, Lauren Hafla, Megan Tibbals, Adrian Dance, Jeff Snyder

"Newmont Mining Corporation’s Carlin (“Carlin”) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (“PTI”) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study.Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load.The secondary crushing plant demonstrated it was capable of reducing the amount of +¾” material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size.For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study."

Jan 1, 2012

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

Mine Safety in Chile ?Since the year 2000 fatality rate averages 34 per year ?1% of world mining labour force but 8% of world?s mining fatalities San Jose Mine Safety ?From 1998 to 2010 eight fatalities ?In 2003 mine inspectors recognized no second means of egress and a raise system was developed ?In 2006 182 workers were injured, 56 of them seriously ?In January 2007, there was a fatality after a rock burst, and the government ordered the mine closed ?Less than a year later the mine was back in operations. It had not complied with some of the basic safety measures ordered. One of those measures was to complete the escape way ladder.

May 1, 2011

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic metres /day of wastewater containing 30-60 mg/1 zinc. demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic con¬trol equipment, the system has evolved to a full-scale operation capable of treating 800 cubic metres/day of wastewater containing 4-11 gm/1 zinc. Treated effluent contains 0.2-20 mg/1 zinc. The hydroxide sludge produced returns to the metallurgical process for the recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing a return from metal recovery.IntroductionWith the goal of reducing environmental contamination, Hudson Bay Mining and Smelting began laboratory testwork, during the late 1960's, into the methods and technology for neutralizing and removing heavy metals from acid mine drainage. Based on lime treatment, early tests showed much promise and culminated in the construction of a pilot-scale test plant at Schist Lake Mine in early 1971.This pilot system utilized technology developed in laboratory studies, and related to work then underway by state authorities in Pennsylvania coal mines. The basic operation consisted of a lime slurry tank, baffle reactor and a free-settling basin. Through three summers of operation, the Schist plant, capable of treating 600 cubic metres/day of minewater, produced a heavy-metal extraction of 99% under normal conditions. Although successful in proving the treatment chemistry, the plant displayed deficiencies in sludge densification and handling."

Jan 1, 1980

By Robert Lamarre

We will present the summary of a number of case studies whereby mining organizations have succeeded in maximizing equipment uptime by reducing the number of maintenance parts stock outs by more than 80% while scaling down total inventory maintenance parts by more than 20%. We will present a thorough comprehensive methodology to improve business processes in order to optimize inventory management and forecasting. We will examine: ? Demand management optimization ? Forecasting organization ? Inventory management parameters optimization ? Improved replenishment processes ? Inventory optimization and the right KPIs and exception reports We will provide cases in point such as Areva in Africa, Cambior (IAMGOLD) in South America, Osisko Mining Corporation, Barrick Gold/Bousquet Mine and Aurizon Mines Ltd./Casa Berardi in North America. We will discuss how Inventory Management World Best Practices operates in a maintenance environment. We will present how an integrated approach, coupled with a strong Enterprise Asset Management or CMMS system with an Inventory Optimization system specially designed to manage spare parts, actually promises and delivers results.

Nov 1, 2011

By L. Cáceres, G. Leinenweber, P. Bustamante

"Given the severe scarcity of fresh water sources in Northern Chile the use of seawater has become the only alternative to allow mining expansion. This option however poses several technological challenges as a result of the high concentration of natural salts that promote various forms of metal corrosion. Therefore the steel piping protection has been a constant challenge for design engineers responsible for solving the problems of corrosion. Known protection alternatives are varied and expensive, a few of them are rubber coatings, protection based centrifuged concrete, extra wall thickness of pipes in combination with corrosion inhibitors, extra wall thickness of pipes without using corrosion inhibitors, and the use of highly corrosion resistant steel materials.In this framework the aim was to study the corrosion kinetics of carbon steel pipe API 5L X70 under electrochemical and weight loss testing. The test conditions include a range of seawater velocities between 0.2 to 3.0 m/s.For electrochemical experiments the API 5L X70 steel specimen was a 4 mm diameter disk embedded in an 8 mm diameter Teflon rod and exposed to seawater. Duplicated coupons were placed in a standard test apparatus that was built according to the standard ASTM D 2688 – 94.The main results were: a) corrosion mechanism explained in terms of the counterparts partial processes which are the hydrogen evolution and oxygen reduction reaction; b) for the test specimen a corrosion band like feature that suggest a lateral dispersion of aggressive solutions from corrosion pits; c) a range of corrosion rates between 1 and 1.96 mm/year for flow rates between 0.2 and 3.0 m/s; and d) a convenient inhibitor dose between 20–25 mg/L for optimum inhibition efficiency to obtain a maximum value of 80% for corrosion efficiency."

Jan 1, 2016

By L. Mohammadi

Outline ?Background on the accident at the Sullivan Mine No.1 Waste Dump ?Holistic approach to understand the reason for accidents (Atmospheric) ?Specific hazards at reclamation sites ?Regular atmospheric risk assessment at reclamation sites ?Fuzzy risk assessment ?Managing risk at legacy sites

May 1, 2010

By H. J. Chalmers

"Since the advent of large volume flotation machines, Cominco Ltd. has actively studied possible application of such machines to their various milling operations. A number of installations have been made and more are on the drawing board. This paper gives a description of these units, information as to choice of equipment, and information as to operating experience. Mechanical and operating details of six installations are summarized. Three different types of machines are discussed.Pine PointThe original Pine Point zinc flotation circuit comprised conventional roughing with two stages of cleaning. Over the years with increase in feed tonnage there have developed two adverse conditions; namely, a reduction in zinc concentrate grade coupled with an increase in MgO in the concentrate. This resulted in higher freight payments along with more severe smelter penalties. An intensive test program, in 1971, showed that the concentrate grade could be raised by 1.5 units of zinc along with a reduction in MgO from 0.8% to 0.47.. Subsequently this was done by adding two additional stages of cleaning using 16 cells of Denver 200-V's. The project was completed in January 1973 at a cost of $510,000 to give an estimated annual savings of about $390,000.Selection of the Denver Model 200-V was based on minimum floor space requirement, availability, and favourable operational and maintenance experience with Denver 100’s. As it happens it was possible to ""shoe-horn"" the 16 cells into place with a minimum of plant alteration. Some problems have been encountered with a tendency to ""sand up"" at high pH, particularly at the corners. Otherwise operational service has been very good."

Jan 1, 1974

By S. D. Logan

This presentation describes a lightweight automobile body structure concept developed at DaimlerChrysler to support a high fuel-efficiency vehicle project. This body structure consisted primarily of large thin-wall magnesium castings and resulted in a more than 40% weight reduction with a minimal cost increase over a conventional steel structure while achieving significantly improved structural performance as evaluated through CAE simulations. One concept vehicle was built for the purpose of demonstrating concept feasibility. Several slides showing the prototype build process are presented. The presentation also describes several large thin-wall die casting body applications that are in current production or have been used in recent production automotive applications and identifies areas where further development could improve the chances of a magnesium intensive body structure becoming a production reality at a later time.

Jan 1, 2006

By C. B. Webber

"Sherritt Gordon's experience with rubber mill liners began in 1964 at the Lynn Lake Farley Mine and continued at the Fox Mine in 1960, and the Ruttan Mine in 1973. This paper describes the history of the performance of rubber mill liners at the three mine operations.LYNN LAKE - FARLEY MINEThe Lynn Lake Farley Mine, which ceased production in 1976 due to exhausted ore reserves, was a 3500 T.P.D. copper-nickel operation; consisting of two parallel rod mills followed by three stages of ball mill grinding. A circuit modification in 1964 necessitated one of the tertiary ball mills to be used as a pyrrhotite regrind mill. This 8' x 5' Hardinge conical mill drawing 225 HP was initially installed with steel liners and lifters. After several months of operation a routine inspection revealed severe channeling and washing behind the liners which was threatening to erode the ball mill shell. It was thought that the highly acidic condition in the mill, due to grinding 100 º6 pyrrhotite, was accelerating the wear of the steel liners. At this time it was decided to reline the mill with rubber liners to see if the wear problem could be relieved, and in December 1964 a set of Skega rubber liners were installed."

Jan 1, 1981

By W. M. Silva, Bittencourt. L. R. M.

Three newly developed alumino-silicate refractory bricks for use in safety lining of aluminum electrolysis cells were compared to one commonly used bricks for the same application. It was shown that the increase in silica content and decrease in permeability led to a sensitive decrease in cryolite attack. Both parameters are of utmost importance in selecting bricks for these cells. The reasons for this observation were the formation of a more viscous liquid after the reaction between molten cryolite and the brick, and the reduction of the rate of penetration. Moreover, a novel mortar with high silica content was tested and has shown improved resistance to molten cryolite. The use of oxidizing atmosphere led to increased attack rate in the brick when compared to reducing condition. The opposite effect was observed in the mortars.

Jan 1, 2004

By James Logan

BC Alkaline CuBC Cu--Au PorphyriesAu Porphyries ?Formed over narrow time interval ~205 Ma ?from silica deficientvsalkali-enriched magmas ?At shallowdepths ?Structuralcontrol ?Cu-Au-Ag, trace Mo ?Oxidized system anhydrite, magnetite ?Multipleintrusions & multiplemineralized centres

May 1, 2006

By J. K. Szymanski

"RÉSUMÉPour maintenir de bonnes performances technique et économique dans l’exploitation par chambres vides (open stope) il est primordial d’assurer un contrôle efficace des limites réelles des chantiers d’abattage. C’est pour cette raison que, de plus en plus souvent, les opérateurs miniers utilisent un dispositif de laser (Cavity Monitoring System: CMS) qui permet de mesurer les dimensions réelles de chantiers en vue de calculer principalement la dilution et les pertes du minerai ainsi que d’autres paramètres. Malheureusement, il n’existe présentement aucune méthodologie commune, qui permettrait d’interpréter ces résultats selon les mêmes critères pour faciliter d’évaluations juste et précise de la réalisation par rapport à la planification en vue d’en apporter de corrections, dans les différentes opérations minières, si nécessaire. Dans la première partie du présent article on discute les principales séquences d’exploitation utilisées dans l’extraction par chambres vides. Par la suite, à l’aide des sections transversales et longitudinales on illustre toutes les phases des travaux miniers. Ceci en vue de permettre au lecteur de comprendre mieux c’est qui peut se passer effectivement dans les chantiers d’abattage. Par après on donne les définitions générales de principaux facteurs de performance technique. Finalement, l’exemple numérique, élaboré à partir des résultats de l’arpentage au laser effectué par la mine Bousquet 2 dans un chantier d’abattage, donne les détails concernant les définitions ainsi que les valeurs de nombreux facteurs de performance technique, qui pourraient être utilisés, par après, par les opérateurs miniers dans le suivi de leurs exploitations souterraines."

Jan 1, 1997

By J. Makgatho, P. Condori, J. Winnett, Fischerm D.

"Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit.This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration."

Jan 1, 2012

By R. W. McConnell, R. P. Racher

High quality steel production requires extended treatment of the steel in the steel ladle. This has a remarkable impact on the steel ladle refractories, e.g. the need for high performance functional refractories like purging plugs. Operational changes such as increasing tapping temperatures, longer hold times and more aggressive secondary metallurgy are countered by the need for thinner refractory linings and longer refractories life. These combined factors have led to a resurgence in interest in magnesium aluminate spinel raw materials. Magnesium aluminate spinels have been used in steel-making refractories for many years, in a variety of different forms. This paper reviews the production, properties and performance of spinels. Recent developments in the applications of spinels will also be discussed.

Jan 1, 2004

By Z. -E. Nakagawa, O. Yamamoto

After the formation of a concentration gradient of SiC within C-C composite, either zircon or mullite thin films were coated on the surface by sol-gel process. Oxidation resistance tests of as-prepared composites with a couple consisting of a ceramic thin film and a SiC-gradient were then carried out in air at the temperature range from 600 to 1600°C. By the coating of zircon with a thickness of 1.5 µm, a pronounced oxidation resistance was observed; the mass loss by oxidation was almost negligible at 1000°C and one hundredth of original composite at 1400°C. In the case of the coating of mullite with a thickness of 1.0 pm, the marked improvement in oxidation resistance over the whole temperature range examined, from 600 to 1600°C, was found with the combination of a SiC-gradient and a mullite thin film

Jan 1, 2004

By S. M. Grillo, Fiori. M., R. Bornioli, C. Marini, S. Fadda

Abstract - The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temper- ature, the composition of the albitizing fluids was modified by an influx of meteoric or other waters.

Jan 1, 1996

By S. M. Grillo, M. Fiori, R. Bornioli, C. Marini, S. Fadda

The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temperature, the composition of the albitizing fuids was modified by an influx of meteoric or other waters. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1997