Search Documents

By S. Makni, A. Faucher, F. Robichaud, A. Bouajila

"Optimizing the ball charge in a grinding mill may be needed to maximise throughput or alternatively, to achieve proper product size in more challenging situations. Efforts to optimise the ball charge however are essentially empirical and suffer from the lack of appropriate, accessible and reliable tools. To address these limitations, a new model-based technology was developed that relies on 3D Discrete Element Method and population balance techniques: it takes on the form of a simulator that aims to significantly decrease the time required to optimise the size distribution and the grinding media load within a ball mill. This paper summarizes the research work related to the development of this simulator. The calibration of the different constituting sub-models will be highlighted. The successful use of the simulator to predict the effect of ball make-up on the grinding product size distribution in one plant is also reported.INTRODUCTION Adjusting the characteristics of the grinding media charge in grinding mills holds significant potential for optimisation of mill performance. For example, properly adjusting the ball size distribution in a ball mill can help achieving specified targets for final product size distribution and/or throughput capacity. However, several problems appear when reviewing the process and the available tools to optimise ball mill load: • The current empirical simulation tools are lacking with regard to the ability to predict the performance of grinding when changes to mill ball make-up are made; • Generally, these tools estimate the top size of the charge so it is difficult to predict the effect of mixed ball make-up; • As the quality of prediction of these tools is low, the operators try to optimise the ball charge by a ""trial and error"" method and proceeding with conservative changes. The influence of these changes on grinding performance is often less than the measurement precision and the improvements then remain imperceptible; • A change in ball make-up may require an average of about 6 months waiting period before reaching the stationary state of mill ball load. This exercise is due to be costly if applied change decreases the mill performance. In its effort towards the comminution process optimisation, COREM R&D portfolio had addressed the herein described opportunity during the last five years This paper describes the technology already developed for the optimisation of ball charge. It takes on the form of a simulator that aims to predict the evolution of the grinding media load, the grinding energy available in the ball mill and the final product size distribution. The simulator was first validated in a pilot scale ball mill and then applied in an industrial case."

Jan 1, 2012

By L. H. Michaud

"Albian Sands Energy (ASE), an oil sands surface mining and extraction operation, is currently undergoing start-up and is scheduled to ramp-up to full production by mid-2003. Startup includes the selection and implementation of over 75 IT systems or computer applications which include: engineering applications; systems required to control mining activities, maintenance, the processing plant and utilities; and also systems required to run the company, such as human resources, finances and inventory/ warehousing.This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in ASE’s approach to identifying system requirements is the development of a business activity model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been led by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that do not meet the company’s expectations. To ensure a more positive outcome, ASE believes that it is imperative that the company’s technical and business people be closely involved in the selection process.Integration of the IT systems is also key, including linking all applications through a data warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company"

Jan 1, 2003

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006

"Ore deposits containing rare earth elements normally contain small amounts of the radioactive elements thorium (Th) and/or uranium (U). These are the naturally-occurring isotopes U238, U235, and Th232 (and associated decay-series daughter products) that are ubiquitous in nature, and that contribute a small percentage of the natural background radiation exposure encountered by humans. The presence of these radioactive materials in the ore deposit creates potential hazards to human health and the environment that must be dealt with properly in the mining, processing, and refining of the ores, as well as management of waste streams and residues. This paper presents an overview of the environmental and safety issues associated with U and Th, with particular emphasis on rare earth mining, processing, and refining projects; the regulatory approaches followed to ensure that rare earth deposits are developed, operated, closed, and decommissioned safely; and the development of information during the project predevelopment work and permitting processes that feed into the design, operation, and closure of tailings impoundments and milling/separation/refining facilities. Case studies will be presented subject to the availability of relevant public information. INTRODUCTIONNearly all ore deposits containing economically-recoverable rare earth minerals also contain small amounts of the radioactive isotopes for the elements thorium (Th) and/or uranium (U) and their associated radioactive decay products. Therefore, the handling and management of these materials in mining and mineral processing operations must be performed so that workers and the environment are protected from harm from Th and/or U (and their radioactive decay products), just as they must be protected from any other potentially harmful constituents present in the ore or introduced in processing. Examples of these might include ores with high sulfide content, which may pose a risk of acid rock drainage, or chemicals used in ore processing and metals production.The purpose of this paper is to present information on how rare earth mining and processing projects with ores containing Th and/or U can be developed, operated, and decommissioned safely according to applicable regulations intended to protect worker health & safety and the environment.It should be noted that some countries are considering developing Th as a feedstock for producing nuclear energy, which could have some effect on future development of rare earth ore deposits. To avoid confusion, that issue is not discussed in this paper."

Jan 1, 2012

By J. F. K. Brown

MR. T. L. McCALL: Planning ahead in coal-mining is essential, but the question may be raised, just how far ahead can we plan. You can overdo it: chat is, you can get in a rut. Never let planning get a hold on you to chat extent. You must be prepared to deal intelligently with any new conditions that arise, and to apply new discoveries. It may become necessary to abandon ? .your plan, make the best you can of the ground you have developed, and start again, with a new plan. So far as the submarine workings of the Dominion Steel and Coal Company are concerned, we cannot know definitely what lies ahead of us under the sea: we must ?base our tentative plans on assumptions, and, as we meet changing conditions, we must change our plans. In the case of inland mines it is possible to bore in advance, and consequently it is generally possible to set out your plans in advance, block out a section of the mine, and develop to obtain a uniform product for a whole year, or perhaps even longer. MR. J. B. MORROW: While planning in coal mining, we must bear in mind chat the consumer also is planning ahead. Some people will tell you that, in ten years time, the demand is going to be all for pulverized co al; others believe that the field for such fuel is limited. Needless to state, planning for a pulverized-coal market is quite a different matter to planning for a general grade, ore stoker, market. In planning, therefore, our endeavour must be to keep a jump ahead of the work being undertaken by the anthracite producers. This year, they are spending about two million dollars-money contributed, not by the Government, but by the industry itself-in the study and promotion of new and improved ways of burning anthracite. For example, they are perfecting small hot-water heaters, and one they have brought out weighs only about ten pounds. I feel that research of this type must be regarded as an essential part of planning in coal mining. We, in the soft-coal industry, are also planning types of more efficient burning equipment and doing other investigational work.

Jan 1, 1937

By A. A. Millar

THE output of coal from the Province of Alberta reached its peak; in the year 1928, when 7,334,179 tons were produced. Following this, a steady decline was recorded, and in 1930 a low mark of 4,564, 290 tons was made. Since that time, however, the tendency has been upward, and this year (1937) 5,551,682 tons were produced, compared with 5,696, 375 tons in 1936 and 5,462,973 tons in 1935. The value of the output in 1937 was $14,434,969, against $14, 720,004 in 1936. The coals of Alberta have been classed under three heads, viz., domestic, sub-bituminous, and bituminous The domestic (or lignite) and the sub-bituminous coals are used chiefly for domestic purposes, with the possible exception of the smaller sizes and the output of the two stripping pits at Stereo and Coal Valley The bituminous output is used mainly by the railways, for locomotive purposes, which, in 1937, accounted for 80.6 per? cenr of the total sales of bituminous coal. A fair proportion is sold for stationary engine and steam purposes and, in 1937, 25,000 tons were used in making briquettes at plants operated by the Canmore Coal Company, Limited, and Brazeau Collieries, Limited. The International Coal & Coke Company, Limited, used 99,500 tons in their plant at Coleman, for making coke. The bulk of the 66,000 tons of coke produced was sold for use at the smelter at Trail, B.C.

Jan 1, 1938

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By D. M. Aloi

In today's evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to "engage" with communities and measure the success of these engagements without a clear understanding of "how" to do this. This move, away from "Corporate" Social Responsibility (CSR) and compliance, develops more of a focus on "Community" Social Responsibility and sustainability. This shift in focus leads to the development of world-class projects that provide sustainable development for people, reduces the incidence of costly delays, and promotes good global citizenship for corporations. The process of "engaging" communities in mining project design and development leads to a stronger license to operate and sustainable development. To create this mutually beneficial relationship between communities and companies, communities must be "engaged" in the mining process as early as possible, preferably during the exploration or the concept phases. How to create this "engagement" remains elusive. How to measure the progress of this engagement is also problematic. The quantitative and qualitative metrics needed to measure both positive and negative impacts of the mining and community relationship will be discussed.

Jan 1, 2007

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

By Robert W. Plummer

"This paper describes the use of Geographic Information Systems (GIS) as a tool for mineral exploration by using the Eskay Creek area of northern British Columbia as an example. Data entry, analysis and output are discussed. Examples of some of the capabilities of the technology are presented.The main benefit of the technology is being able to perform complex and sophisticated searches of large and diverse data sets to highlight exploration targets. A GIS is a powerful data management tool that can be used in mineral exploration. It is a computer based system that is designed for the collection, storage and analysis of objects and phenomena where geographic location is an important characteristic. The main function of the GIS is to produce information for the geologist from a variety of sources (geology, geophysics, geochemistry, mineral deposits and so forth) quickly and efficiently. This allows the geologist to examine large amounts of data in a fraction of the time than can be done using conventional manual methods."

Jan 1, 1992

By David H. Searle

This paper will discuss the common trends existing in various Canadian jurisdictions for the closure and reclamation of mines. Included will be a discussion of the requirement to post security as well as its form and how security is calculated and refunded. Reclamation can no longer be left to the end of mine life. Progressive reclamation must occur throughout mine life and must be part of the mine plan from the beginning.

May 1, 2006

By M. C. Bétournay, J. E. Udd

"The Mining Laboratories of CANMET are the principal federal government vehicle for the delivery of mining research in Canada. With research being performed at five locations, which are mostly mining communities, the laboratories are in close proximity to the industry which they serve.The Mining Laboratories have three principal roles: (1) to support government in its development of policy; (2) to aid industry in the enhancement of productivity; and (3) to improve the health and safety of Canadians,both in the workplace in mines and around abandoned mine sites.From 1994 to 1996, CANMET’s mining research was re-focused into four programs. These are: (1) Underground Mine Environments; (2) Mine Mechanization and Automation; (3) Ground Control, and; (4) Coal Mining Health and Safety.In this paper, the authors outline the work of the Mining Laboratories and also identify the areas considered to be primary targets for future mining health and safety research in Canada."

Jan 1, 1997

By Ruy L. Rodrigues

Vale is in the early stages of commissioning its Onça Puma nickel operations. The project is meant for the production of 58,000 tpa of nickel contained in ferro-nickel, substantially contributing to the company?s vision to achieve world leadership in the nickel business. Mineral resources will be exploited from the homonymous deposits in the Midwest of state of Para, Brazil ? some 100 km southwestwards from the company?s Carajás iron ore properties. Resources as of 83 Mt at 1.73 % Ni will sustain a mine life of approximately 40 years. The property was acquired in late 2005 and Vale has since extended the engineering studies and proceeded with the implementation. Nickel will be mined from saprolitic ore at a rate of approximately 10 Mtpa (ore plus waste) in early years ? ramping up to some 15 Mtpa 7 years later ?, to feed the plant at a rate of 2.5 Mtpa. The process uses conventional RKEF (Rotary Kiln Electric Furnace) pyrometalurgical route whereby the ore is homogenized, calcined in rotary kilns, melted in electric furnaces and further refined to ferro-nickel. The plant has been designed and constructed applying the latest available technology, aligned with Vale?s vison to exceed the highest existing standards for environmental control, health and safety and productivity in the industry. Total investments in these operations are anticipated to correspond to USD 2.3 Bi and will materially contribute to the regional development and well being of the nearby communities and other stakeholders.

May 1, 2010

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By M. L. Joy

The heat pipe is a self-contained, passive structure that uses a liquid-vapour fluid cycle to provide high thermal conductance . Through the proper selection of working fluids and container materials, heat pipes have been operated at temperatures ranging from less than -300°F to more than 3,000 °F. The passive nature, high efficiency and configuration flexibility of the heat pipe are presented. The application of McDonnell Douglas Astronautics Company Cryo-Anchor® heat pipes for foundation and support stabilization in permafrost regions is discussed. Using the proven Cryo-Anchor technology base. a proposed application of heat pipes in a cold -region mine ventilation system heat recovery heat exchanger is presented. Information obtained from the development of an air-cooled heat pipe steam condenser provides the technical basis for large -scale heat pipe applications.

Jan 1, 1978

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By James Scott

Outline Deposit Overview and Brief History ?Geologic Setting ?Local Geology ?Petrography ?Geochemistry ?Mineralization ?Geochronology ?Conclusions Deposit Overview ?Porphyry Cu-Mo-Au ?Discovered 1957 (BIK Syndicate) ?Various programs, most significant: ?Hecla(1970s) ?Teck(Late 1970s Early 1980s) ?Copper Fox Metals (2005 -Ongoing ?optioned from TeckComincoin 2002) ?Measured and Indicated Resources: ?847Mt grading: ?0.292% Cu ?0.019% Mo ?0.202g/t Au ?1.796g/t Ag ?Total ~ 0.485 % Cu Eq.

May 1, 2006