Search Documents

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

By Magnus Evertsson, Johannes Quist

HPGRs have since introduced in the 1980s (Kellerwessel, 1993; Schönert, 1988), now become integral comminution units at several minerals processing plants around the world. Even though a lot of the initial issues concerning performance, availability and wear have been addressed and solved there are still phenomena and aspects which can be improved and understood further. Schönert and Sander (2002) presented experimental results and a mechanistic model including the internal force dynamics between the rollers and the compacted bed. They derived expressions for the pressure distribution involving most of the influencing terms and effects. However, in order to solve the differential equations several of the terms vanish by assumptions. The Schönert and Sander model reflects the experimental data in many aspects but the predicted shear force distinctly deviates from the experimental results at the angular position of the peak pressure level. This finding suggests that the particle to particle interaction and breakage process in the different zones seen in Figure 1 are complex and difficult to model using analytical models. A numerical modelling approach using DEM does not require the same amount of assumptions and simplifications of boundary conditions. Hence such modelling may provide further knowledge and vital understanding. In this paper the breakage process is simulated in order to investigate the shear slip behaviour and how it relates to different operating variables. A laboratory scale HPGR corresponding to the experimental setup used by Schönert (2002) have been modelled in EDEM (DEM-Solutions). The bonded particle model (BPM) is used for modelling quartz particles (Potyondy, 2004). The breakage model strength parameters are calibrated against interparticle breakage experiments in an Instron 400RD compression device. The contact model parameters are calibrated using calibration methods developed by Quist (2015). The floating roller dynamics are modelled using a spring-damper system. Results present insights regarding the interparticle slip behaviour as well as the frictional tangential force distribution on the rollers. The simulated roller pressure distribution shows good correspondence with previously reported findings in the literature.

Jan 1, 2016

By Mario Giavani

"IntroductionBy the 1980s, the continuous casting process had almost replaced the ingot casting of steel in Japan, Europe and North America. While economic benefits were probably initially the prime motivator, the transition rapidly proved that continuous casting in conjunction with ladle metallurgy offered a much greater degree of process control and made possible routine steel specifications not previously available.This new technology demanded improved procedures for the quantitative addition of the required metallurgical reagents, especially as regards the more volatile or toxic elements such as calcium , boron, carbon, sulphur, lead and tellurium. The injection of a thin steel tube containing the additive into the metal bath of a ladle refining station offers the best procedure for this. In the industry this has been referred to as ""Cored Wire "".Operators using this technology find that they are faced with balancing the injection speed against the small cross section of the tube to feed the required amount of reagent within the short time span available to the operation. Large-ladle shops requiring major quantities usually resort to multiple machines and high speeds. Many machines approach a maximum feed rate of 400 m/min. Higher speeds exceed the melting rate of the system, and the ferro static buoyancy of the tube will cause it to coil up the ladle wall and possibly resurface into the slag layer, and even eject itself above the surface. Under these conditions, exact control of element recovery becomes difficult, especially with the commonest addition, calcium silicon alloy.Many experts are persuaded that the final melting position of the carrier tube has major importance in establishing consistent element yield to the bath.For instance, the vapour pressure of calcium at l500 °C is close to I bar. Reaching a melting depth sufficient to accommodate this value is considered to be critical to achieving an acceptable and reproducible yield.Many studies have elaborated semi-empirical formulae to establish the melt zone depth, connecting this value essentially to the diameter of the tube , the injection rate and the superheat of the steel. The author's experience in steelmaking could not confirm such formulae in many cases, and he set about to develop a mathematical model which would be useful in addressing this problem, taking into account the several parameters which will regulate the behaviour of a filled tube immersed in molten steel."

Jan 1, 1991

By L. M. Pidgeon

Abstract The production of metallic calcium, by reduction of lime with aluminium, was investigated. Using a modified form of the effusion method, the vapour pressure of calcium above the reaction: 4CaO + 2Al ~ 3Ca + CaO.AI203 was determined and found to vary from 1.0 to 1.3 mm. Hg from 1,150° to l,200°C. From the magnitudes of the various thermodynamic quantities involved, together with a consideration of the known chemical characteristics of the reaction, it was suggested that the reaction proceeded by reduction of lime with aluminium vapour. INTRODUCTION The conventional production of metals by reduction of their ores by carbon (or carbon monoxide) may be represented by the equilibrium: MO+ R [] RO+ M . . . . . . . . . .(1) where MO represents the metal oxide, and R the reducing agent (carbon or carbon monoxide). The free energy change ?F° associated with the reaction is given by -?F° = RTlnKp . . . . . . . . ... . (2) where R is the gas constant, T the absolute temperature, and KP the equilibrium constant. It should be noted that ?F° represents ? the standard free energy gained by the system and hence -?F° is the free energy gained by the surroundings - and that as ?F° increases K must decrease, and conversely. For metals above manganese in the electromotive series, the ?F° associated with reaction would quantity and from it can be seen that this corresponds to a small fraction for K. The equilibrium pressure of the oxide of carbon represented by RO is then too near its concentration in the furnace gases for the reaction to proceed in an internally fired furnace. For the practical reduction of such metals, fuel fired furnaces are inadequate. Electric furnaces may be used to give higher temperatures with lower concentration of carbon oxides and the reaction may still proceed. However, for many metals such as calcium and aluminium the formation of stable carbides or acetylides may prevent production of the metal by this reaction. In this case, either electrolytic methods must be used, orrecourse must be had to reducing agents other than carbon. It is the latter method which is under consideration here.

Jan 1, 1948

By D. B. Apel

As depths to the ore bodies keep increasing around the globe, the problem how to deal with the increasing temperature of undisturbed rock mass becomes very important. In extreme cases the rock temperature at the bottom of the mine could raise up to 80 °C. In deep mines, geothermal heat is considered as the primary heat load contributor, which accounts for 50?90% of the total heat load depending on different geological conditions. Thus the geothermal heat control in underground mines is the most important and demanding issue to ensure a suitable working environment. In this study, expanded perlite aggregate (EPA) was incorporated as a lightweight substitute for sand. Five mixtures were prepared using 0, 25, 50, 75 and 100% replacement ratios of sand by EPA. These, mixtures were tested in the laboratory for both the insulating and strength properties of the developed shotcrete. The goal of this research was not only to develop shotcrete which would exhibit good insulating properties but also which would exhibit strength properties similar to the regular shotcrete. This paper not only reports the results of the laboratory tests but also discusses the output of numerical model which was performed to evaluate the benefits of using the insulating shotcrete in reducing the cooling costs at hot underground mines.

Aug 1, 2013

By R. P. Hackl, P. G. West-Sells

Carbonaceous gold ores are particularly attractive for leaching by ammonium thiosulfate as the gold thiosulfate complex is not significantly adsorbed by the organic carbon present in the ore. A technically and economically feasible process for treating these ores with ammonium thiosulfate has been developed. In this process, gold is extracted by leaching the ore with ammonium thiosulfate, the solution is separated from the ore by counter - current decantation, the gold is recovered by precipitation with ammonium sulfide, and finally the gold containing product is upgraded by reacting the elemental sulfur present in the precipitate with ammonium sulfite. The precipitation filtrate is recycled back to the grinding step to close the solution balance. Reagent consumption is not excessive. Besides precipitating gold, the precipitation step removes most deleterious solution impurities and converts a portion of the polythionates back to thiosulfate. This paper discusses the optimization of the leaching, precipitation, and upgrading steps. The results of a 10 kg/h pilot plant campaign are also discussed.

Jan 1, 2005

By D. Gorc, T. M. Fraser, Z. T. Nikic, R. Pesalj

"Mount Polley is an alkalic porphyry copper-gold deposit of Lower Jurassic age within the Quesnel terrane in south-central British Columbia. The silica-saturated Mount Polley intmsive complex is assumed to be coeval with volcanic rocks of similar composition in the Nicola Group in which it was emplaced. Other intmsions and some of the volcanic rocks in the Mount Polley area are silicaundersaturated and contain feldspathoids.The Mount Polley deposit is characterized by multiple intrusions that vary from diorite to crowded plagioclase porphyry to monzonite. Intmsion breccias are associated with some of the intmsive phases. Abundant hydrothermal breccias occur on the margins and above plagioclase porphyry intmsions. These breccias provide the main host for mineralization and are associated with the highest concentrations of copper and gold. The breccias are subdivided into four distinct types based on the dominant hydrothermal mineral in the matrix. Actinolite breccia is developed in an elongate zone within the core of the Central zone and grades laterally and vertically into biotite breccia to the southeast. Magnetite breccia is irregularly distributed and is relatively sparse throughout the deposit and albite breccia is dominant in the West zone. Pervasive and vein-related alteration correlates with the breccia types. The core of the hydrothermal system at Mount Polley is subdivided into three zones: actinolite, biotite and K-feldspar-albite. The margins of the core zone are overprinted by a discontinuous zone of calc-silicate minerals. This intermediate zone passes outward into propylitic alteration. Mineralization is most prominent within hydrothermal breccias and is generally present as disseminations, blebs within the matrix and abundant veins. Mineralization is associated with a chalcopyrite-magnetite-bornite assemblage in the core of the deposit passing out into magnetite-pyrite-chalcopyrite. Relatively constant copper to gold ratios suggest that both metals were precipitated under similar conditions.Hydrothermal breccias are genetically related to the emplacement of the crowded plagioclase porphyry melt. Crystallization of the melt was probably accompanied by volatile/aqueous exsolution, forming a water saturated carapace. Decompression of the chamber in response to magma withdrawal, fracture propagation and possible fault movement allowed hydrothermal brecciation to occur at the apex and margins of the intmsion. Alteration and mineralization appears to have been controlled by fluids migrating away from the plagioclase porphyry."

Jan 1, 1995

By C. DeLong

"The Mt. Milligan porphyry copper-gold deposits are in central British Columbia, 155 km northwest of Prince George. Mineralized outcrops and float were discovered in the Mount Milligan area by prospecting. The most recent discoveries, which utilized lithogeochemistry, were in 1983. Areas containing the outcrops and float then were investigated by geological mapping, soil and lithogeochemical sampling, ground and airborne geophysical surveys, trenching and diamond drilling. This work led to the discovery of the Mt. Milligan Main deposit in 1987 and the Southern Star deposit in 1989. Extensive diamond drilling continued until 1991 and delineated a measured and indicated resource of 299 million tonnes grading 0.45 g/t Au and 0.22 % Cu from the combined deposits.The Mt. Milligan deposits lie within the Early Mesozoic Quesnel Terrane and are hosted by porphyritic monzonite stocks and adjacent volcanic rocks of the Takla Group. The Mt. Milligan Main deposit is centred around the MBX stock and Rainbow dike, and the Southern Star deposit around the Southern Star stock.Potassic alteration is extensive within the stocks and in volcanic rocks adjacent to the MBX stock and Rainbow dike. Propylitic alteration surrounds the potassic alteration and decreases in intensuy away from the stocks. Mineralization consists mostly of pyrite, chalcopyrite, lesser magnetite, and minor bornite, molybdenite and gold.Mineralogical zoning is well-developed within the deposits. A biotite-rich subzone forms the core of the potassic alteration zone and hosts most of the copper and gold. Numerous polymetallic veins lie within the propylitic alteration zone just beyond the limit of porphyry-style copper-gold mineralization."

Jan 1, 1995

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By Q. G. Reynolds, R. T. Jones

"Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. A mathematical description is presented for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are shown to have a significant effect on the residence time distribution.INTRODUCTIONThere are some processes in which the time spent by the feed material in a smelting furnace plays a significant role in determining the extent of the reactions between metal and slag and influences the degree of settling of metal droplets from a molten slag.Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. Here we will focus on producing a mathematical description for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are studied.Previous work (Jones, la Grange and Assis, 1997) has studied the effect of retention time on the degree of cobalt recovery achieved in a slag reduction process. In that work, a method was proposed for the calculation of the mean residence time of the contents of a pilot-plant furnace. That approach is to be extended here for the purposes of providing a more general design or scale-up tool.The maximum allowable depth of molten material in a given furnace is affected by such factors as the desired batch size (or the size of the ladles) and the pressure of the molten material that the tap-hole and surrounding system can withstand. Within these constraints, there might be some scope for choice of taphole position. The effects of this choice need to be understood mathematically."

Jan 1, 2012

"The rocks of Notre Dame Bay form part of the Central Paleozoic Mobile Belt (Williams, 1964) of the Newfoundland Appalachians. The Central Paleozoic Mobile Belt of the northern part of the island consists predominantly of Lower and Middle Ordovician rocks overlain by Silurian elastic and volcanic sequences and underlain in the marginal zones of the belt by polydeformed metamorphic rocks of the Gander Lake Group (Kennedy and McGonigal, 1972) in the northeast and the Fleur de Lys Supergroup (Neale and Nash, 1963; Kennedy, Phillips and Neale, 1972) in the northwest. The Ordovician rocks of the Central Mobile Belt have been subdivided into a number of local groups in different parts of the region. The Lush's Bight Group was first defined by MacLean (1947) . Recently Marten (1971) has revised the definition of this group, as shown in Table 1 and his revised definition is accepted in the present paper. Plate tectonic models that have been proposed for the development of the Newfoundland Appalachian System have indicated that the mafic volcanic rocks of western Notre Dame Bay represent oceanic crust (Bird and Dewey, 1970; Dewey and Bird, 1971; Church and Stevens, 1970) which marks the remnants of the proto-Atlantic Ocean first proposed by Wilson (1966) . Such models infer that the mafic volcanic rocks constitute the upper part of an ophiolite sequence. Analyses of the lavas show that they are tholeiitic and support this conclusion (Papezik and Fleming, 1967; Smitheringale, 1972) . A complete ophiolite sequence, consisting of peridotites overlain by gabbros, overlain by a sheeted diabase dyke complex which passes upward into pillow lavas, occurs at the base of the Snooks Arm Group (Upadhyay et al., 1971 ) . Sheeted diabase dykes are known to underlie the lowest mafic pillow lavas of the Lush's Bight Group at several localities in Notre Dame Bay (Strong, 1972, and pers. comm.) . However, several conflicting points about the geology of this region suggest that although a typical oceanic crustal sequence of Lower Ordovician age is present, older rocks occur within the ophiolite terrane in several places (Williams, Kennedy and Neale, 1972) ."

Jan 1, 1972

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

By J. E. Gill

Introduction During the past summer, detailed geological mapping was extended to cover the entire group of 31 claims owned by Waite-Ackerman-Montgomery Mines, Ltd., and considerable new information was revealed by development and exploratory work underground. These new facts provide a more complete view of the lithology and structure of the area than has heretofore been available. They also necessitate revision of certain interpretations presented last year by Peale (l), and have served to straighten out some of the problems suggested by Porritt (2). The purpose of this paper is to outline in a broad way the relations as now understood and to discuss in detail certain points which should be of interest to members of the Institute. Maps and records by the mine staff have been freely used in arriving at the interpretation presented in the following pages. The writers are especially indebted to Mr. R. V. Porritt, the mine manager, with whom many of the problems touched upon were discussed on the ground and whose intimate knowledge of the geology of the underground workings aided greatly in testing various hypotheses. The writers have profited greatly, also, from close association with Dr. W. F. James during the course of the work. Permission to publish the included data has very kindly been given .by the management.

Jan 1, 1932

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By C. R. Tang

The respirable dust real-time monitoring equipment export information is complex, and electromagnetic wave wireless transmission is affected largely under mine conditions. The respirable dust concentration information transmission method based on led light equipment is proposed. The respirable dust concentration data of the individual real-time monitoring equipment is encoded to fit the system transmission; the encoded signal is modulated onto the LED mine lamp; the light signal is transmitted by the spatial channel; the signal is received by the receiver to the photoelectric conversion to restore the respirable dust concentration data for subsequent processing. Simulation and verification experiments showed that the respirable dust concentration information transmission method based on led light equipment can achieve the LED miners? lamps visible light wireless data transmission.

Aug 1, 2013

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds. Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a ?diamond friendly? method of comminution. Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso).

Jan 1, 2012

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By L. R. P. de Andrade Lima, D. Hodouin

The paper presents a survey of the possibilities of the simulation techniques for improving the design and operation of gold processing plants. The procedure to construct kinetic models that are used in simulators is first reviewed, and examples are given for cyanide gold dissolution and gold adsorption on carbon. Then, an overview of the structures of the plant simulators is proposed, and the simulation equations formulated for a carbon-in-leach process. Finally, the potential of simulation methods is illustrated by four examples. The first one shows how it is possible to use a simulator to design a cascade of leaching tanks while optimizing an economic performance criterion. The second one illustrates the role of simulators for optimal tuning of the cyanide addition strategy in a leaching circuit. The third example focuses on the power of simulation to design carbon transfer strategies in a carbon-in-pulp process. Finally, the last example shows the role of on-line simulators for optimally supervising the automatic control of cyanide addition into leaching tanks.

Jan 1, 2005