Search Documents

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By G. R. Webber, P. J. Whittaker

"A multielement (Au, Cu, Pb, Zn, Ni, c-, Ag, As, Hg, Co, and S) geochemical rock sampling survey was carried out in 1977 in the Munro Township area of Ontario to assess the application of rock geochemistry for gold exploration in the region. Detailed sampling with analysis for gold and arsenic was done in 1986 in the immediate vicinity of the Croesus Mine.Samples of quartz veins and rock formations were taken in regional traverses and in more detail near old showings, prospect pits, and trenches. Quartz, graywacke, carbonate rock, and rhyolite contain the highest concentrations of gold for samples taken away from the old workings. Ultramafic rocks and gabbro have uniformly low gold. Basalt samples have slightly higher geometric means, but individual samples contain high gold concentrations. Multielement highs are mostly in mineralized quartz samples. Gold distribution is independent of other elements in most other rock types. Samples near old showings possess elevated concentrations of gold indicating that prospecting for individual mineral deposits by bedrock sampling is feasible. Concentrations of gold greater than 100 ppb are mostly within 30 m of old workings. Those samples which contain greater than 1000 ppb Au were obtained from quartz veins, basalt, graywacke, and rhyolite.High concentrations of gold were not notably concentrated near the Contact Fault although some anomalous samples came from near and on both sides of the fault. Arsenic concentrations are elevated near the Contact Fault. Detailed sampling near the Croesus Mine suggests that gold was introduced with faulting, alteration and quartz veining. Gold and arsenic have been added to the wallrock in the vicinity of the main veins."

Jan 1, 1989

By J. Peace, J. R. Fletcher

"British Steel has increased its usage of stainless steel for bunker, silo and chute linings to reduce maintenance costs and improve productivity.A generation of low cost 12% Cr steels has been specifically developed to satisfy the needs of hardness, flow promotion and through life costing which are demanded by bulk solids handling industries.The range of stainless steels include:• a very hard martensitic grade which is particularly suitable for high stress applications where impact and abrasion are predominant;• a titanium stabilized duplex steel for structural applications, as well as low friction , medium abrasion resistant wear liner plate; and• a ferritic stainless steel with rubber backing for low stress application where flow promotion of product is the predominant requirement.Industrial applications and experiences along with methods of fixin g the stainless steels will be discussed in conjunction with the relative through-life costs of the products.IntroductionBritish Steel has become one of the most efficient steel manufacturers in the world, with improvements seen in productivity, quality, delivery, performance and response to the needs of the worldwide market place.Part of this success stems from reductions in engineering downtime in the key areas of its operations, by the introduction of better engineering design and the use of enhanced materials where significant cost benefits have been identified.The nature of producing iron and steel requires the use and handling of a number of raw materials with wide ranging properties, each calling for a different approach to solving the difficulties encountered in storing and transporting these materials to their respective point of use. Figure 1 shows steel production for 1988-89 where over 30 million tonnes of raw materials were handled in making 14 million tonnes of liquid steel at British Steel's five integrated works.Typically solid raw materials include, iron ore, coal, limestone, ferro alloys and scrap. Intermediate products such as coke and sinter create their own specific handling and wear problems.Coals and ores are shipped into the United Kingdom from several sources, and have a great variety of properties. Some coals can be extremely wet and sticky, whereas others are dry and dusty . The ores handled can vary from wet concentrate and fines to heavy angular rubble and pellets. These raw materials are off-loaded, stored and conveyed through British Steel's own port facilities at Port Talbot, Immingham, Redcar and Hunterston. British Steel also produces the majority of its own coke and all its own sinter. Coke and sinter are frequently handled at elevated temperatures which cause other handling problems."

Jan 1, 1991

By T. P. Johnson, A. Vathavooran

"Conventional mining operations can produce a wide range of wastes containing gold and other precious metals but which are less suitable for processing by traditional methods. There are also types of ore that do not fit easily into a traditional processing flowsheet, e.g. because the refractory nature of their minerology or the combination of valuable metals is less suitable for traditional processes. Nevertheless, these potential sources of valuable metals remain unexploited resources that have attracted growing interest in the metals and mining industries over recent years. The challenge is therefore to develop and use alternative processing methods that have the flexibility of operation to cope with a wide variety of material types and tonnages, whilst providing high recoveries for valuable metals. Tetronics’ DC plasma smelting technology achieves industry-leading recovery rates for precious metals from a wide range of input materials and initial precious metal concentrations, whilst generating an inert slag-based material as a by-product (even when starting from a hazardous waste input material), approved within the EU for use in construction applications. This paper describes how this technology can be used as a key part of an overall process for the recovery of precious metals from these interesting materials.INTRODUCTION The extraction of gold from its ores by various forms of cyanide leaching has been practised by the mining industry for over a century (Minerals Council of Australia, 2005) and it remains the primary extraction method in a wide range of mining operations. The ability of cyanide to extract gold efficiently and quickly from lower grade ores without extensive additional processing, coupled with well-known methods to recycle the cyanide for re-use within the process mean it is often both the most economically preferable and environmentally acceptable method for recovering gold. As a result, 88% of all gold produced from mines in the USA in 2014 was recovered via leaching of open heaps or dumps (UGGS, 2016). Nevertheless, there are occasions where certain combinations of mineralogy and other circumstances reduce the effectiveness of cyanidation techniques, so that ever more elaborate additional processing steps are required, with inevitable increases in operating costs (Swash, 1988). In these circumstances, which are likely to be more common in future as ore qualities diminish, other methods of extraction may offer better alternatives. Whilst much less commonly used for Au extraction at present, pyrometallurgical methods are amongst the longest-established of these alternative approaches and merit serious consideration in such cases."

Jan 1, 2017

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By Rob Morrison, Peter Cameron

"Many products and technologies have been developed from outcomes of research projects carried out by the Julius Kruttschnitt Mineral Research Centre (JKMRC). When these products and technologies are applied to the design and optimisation of blasting, comminution and separation, improvements in profitability can be realised.In 1970 Alban Lynch promoted two practical ideas to improve plant operations:• Ore and equipment properties can be separated allowing experience with one type of ore or equipment to be transferred to other types of ore and equipment. If this experience was encapsulated in a mathematical model, then these properties could be combined and used to simulate (ie. to design and to optimise) complete mineral processing circuits.• Many problems associated with scale-up from laboratory to industrial equipment could be eliminated by experimental work on full-scale equipment in the plant.Many JKMRC research projects have focussed on the development of models of unit operations in mineral processing and their application to process simulation.Models of comminution and classification developed at the JKMRC have been used since the early 1980's. Ore characterisation techniques developed to support these models are licensed world wide through JKTech. The application of comminution modelling techniques to blasting, which optimises the process feed size distribution is used in Mine-to-Mill® projects. The advances in the understanding and modelling of froth flotation over recent years have provided the opportunity for integrated ore characterisation and process optimisation from resource to product.JKMRC project outcomes often provide proven opportunities for the mineral industry to improve performance and productivity. JKTech was established in 1986 to commercialise and market the most promising outcomes and thus ensure their continuing availability to the mineral industry.They include:• Commercial software (JKSimMet, JKSimBlast and JKMetAccount).• Monographs (Comminution and Blasting).• Technologies (Mine-to-Mill® and flotation optimisation).• Hardware products (JKFrothCam, JKJetLift® and the Mineral Liberation Analyser).This paper summarises these technologies and their benefits."

Jan 1, 2003

By Kyle Paulsen

The Cameco Key Lake mill began processing U-bearing waste rock from the McArthur River mine in 2000. This ore often contains elevated levels of calcium (>4% by mass), resulting in less than favourable conditions in parts of the Key Lake mill, yet still contains U3O8 at a concentration of about 0.3%. To recover the U3O8 and reject as much calcium as possible, modifications were made to the grinding circuit in late 2007 to include a gravity concentrator. The concentrator allows this mineralized waste to be processed separate from the regular blend material, rejecting calcium and concentrating U3O8, thus improving the operating conditions in areas such as SX. This will be presented in greater detail along with results and further work.

Aug 1, 2010

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By B. Zhu

With the challenge of clearing steel production and increasing of the productivity of converter, the application of hot metal pretreatment technology in torpedo car become a key process in the steelmaking. In this article, the technologies, production and development trend of Al2O3-SiC-C bricks for torpedo cars in China are reviewed, the current application situation and main requirements for the Al2O3-SiC-C bricks are also addressed.

Jan 1, 2004

By L. Bratek, K. Jaworek, M. Czaplicka

Methods for arsenic compound removal from aqueous solutions include processes such as: coagulation, adsorption, membrane techniques, electrochemical and biotechnology techniques. Advanced oxidation using both UV radiation and strong oxidizing agents such as ozone and hydrogen peroxide may also decompose these compounds. It is known that effluents from metallurgical processes contain inorganic arsenic compounds in addition to the organic compounds such as: dimethylarsinic acid and phenylarsonic acid. This paper presents the conditions that lead to the formation of deposits containing mainly arsenic, such as pH, the wavelength of the radiation and the type of oxidant, for this type of effluent.

Jan 1, 2014

By Brian Penney

"The Iron Ore Company of Canada (IOCC} has mined and processed an iron deposit in Western Labrador along the Labrador-Quebec border since the early 1960' s. Current capacity is approximately 19 million tonnes of concentrate, 70% of which is converted to pellets at these facilities.The ore deposits are located in hills rising 150 to 300 meters above the adjacent lakes, and most of them are covered by very little overburden. The iron minerals are mainly specular hematite and magnetite hosted in a quartz formation. Crude ore averages 40% Fe that is concentrated to 65.5% Fe. IOCC is an extensive operation extending from Labrador City NF to Sept-Iles Quebec. It consists of open pit mining, concentrating, pelletizing, railway, and dock loading facilities.The Concentrator liberates iron from the silica by crushing and grinding the ore to -14 mesh (-1190 microns}. Ground ore is concentrated in spirals and filtered for transportation. Spiral tailings are treated in a Magnetic Recovery Plant (Mag Plant} that recovers lost magnetite. Mag Plant tailings are treated in a Hematite Spiral Plant (Hem Plant} that scavenges fine iron remaining in this stream.This report deals with ongoing iron recovery initiatives within the ConcentratorIron Losses in the ConcentratorIron recovery at IOCC is approximately 70.5%. This compares with recoveries that range from 65% to 86% for other iron mines in our area. Other world large iron ore producers dig and ship concentrate quality ore directly out of the ground and have an effective recovery of 100%. With increasing costs for labour, equipment, and supplies an increase in iron recovery is required to keep the operation viable.More than 90% of our iron concentrate is produced by gravity separation using spirals. The physical characteristics of the iron minerals that most effect recovery are mineral grain size and degree of liberation. We divide ground ore into three size categories -coarse, intermediate, and fines. A brief description of each size fraction follows:"

Jan 1, 1996

By H. L. Cheng, C. H. B. Leitch, C. T. Hood, A. J. Sinclair

"Epithermal Zn-Pb-Cu-Ag-Au quartz-carbonate-barite veins at the Silver Queen mine near Owen Lake, west-central British Columbia, are hosted by Late Cretaceous Tip Top Hill andesitic volcanic rocks. The veins form a rectilinear northwest-northeast pattern that differs slightly from regional structural trends. The main northwest-trending veins are oriented very close to the trend of regional northwest faults, but the crossing veins tend to be more east-north-easterly (070 degrees)compared to a regional north-easterly trend (040 degrees). The character of the veins suggests they are extensional features formed by dextral slip related to Paleogene oblique subduction, or intrusion of magma at depth, or both.In detailed exploration at the mine, the veins cannot be modelled as simple tabular sheet-like bodies. Instead, they are complex structures that divide and rejoin, forming multiple veins or stringers, or are found in shear zones as replacement features with quartzsericite- clay-carbonate-pyrite alteration haloes of variable width that make definition of vein margins and correlation from hole to hole ambiguous. In addition, individual veins within each of the main structures have en echelon characterboth along strike and down dip.Geological and assay data must be carefully studied to define the margins of these complex veins before any estimation of ore reserves may be made. Where multiple veins occur in a section, ore/gangue mineralogy, assays, character of wallrock alteration, and thickness of vein and mineralized hangingwall, median and footwall zones must be used to evaluate continuity of mineralized structures. Well-defined sections are projected into areas of increasing complexity. Once the vein boundaries are defined, metal concentrations, important metal ratios(Au/Ag, Pb/Zn, Cu/Zn), and true thicknesses of the vein provide the basic data for reliable ore reserve estimation."

Jan 1, 1991

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

By David Evans, David Barnes, Robert Raponi

"The Williams Mine processes, on average, 6,450 t/d of gold bearing ore using two parallel grinding circuits, leaching and C.1.P., carbon stripping, electrowinning and refining. At present, each grinding circuit consists of a SAG mill in closed circuit with a spiral classifier and a ball mill in closed circuit with two stages of cyclones.Since grinding has always constituted the largest portion of milling costs, the Williams Mine has been proactive in trying to reduce such costs through innovative changes. One project under consideration is the replacement of one spiral classifier by a vibrating screen.This paper discusses the testwork performed to evaluate the replacement of one spiral classifier by a vibrating screen, and the preliminary engineering performed to date.IntroductionThe Williams Mine, located in northwestern Ontario, approximately 40 kilometres east of Marathon, is part of the Hernia gold camp. The mine is operated by the Williams Operating Corporation and is owned by the Teck Corporation and Homestake Canada Incorporated. Operation of the mine started in October 1985 at a rate of 3,000 t/d. After a mill expansion in August 1988, throughput increased to 6,000 t/d. Production has increased steadily since the mill expansion and in 1995, an average of 6,450 t/d of ore was processed at a recovery of 95.1 %."

Jan 1, 1997