Search Documents

By Andrew Cormier

"The Early YearsThe Grand Lake coal fields in New Brunswick undoubtedly can claim the distinction of being the first part of North America from which coal was mined and exported. The diaries of the Governor of Massachusetts during the first half of the 17th century clearly establish this fact. There is also a reference in the Massachusetts Colonial Records which indicate that coal exports to New England were carried on as early as 1639.It has generally been believed that Cape Breton mined and exported the first coal; but no account has yet been found to show that this took place earlier than 1676. Both at Grand Lake and Cape Breton the coal was near the surface and removed by hand.When the country passed entirely into British control, Joseph Garrison, a grantee of Maugerville in 1765 moved to Jemseg. While surveying the north side of Grand Lake he discovered outcroppings of coal on the shore of the lake and further inland along the banks of streams. It was he who named Newcastle Creek in reference to Newcastle in England, which was widely known for its coal mines. Joseph Garrison died in 1783, the same year that an influx of United Empire Loyalists increased settlement in Newcastle Creek in the area now known as Minto. Many Loyalists also settled on the shores on both sides of Grand Lake.At a number of points where streams cut channels through the overlying strata, the coal seams were exposed and it was at such outcroppings that the early operations were carried on. A tunnel was driven in the seam from the foot of the bank, affording both an outlet for the coal and natural drainage from the workings. The coal was loaded into boxes and wheeled over wooden tracks to a point on the surface where it could be dumped into wagons and hauled either direct to destination or to where it could be loaded into boats and conveyed via Grand Lake, Jemseg and Saint John river to points of distribution.In the latter part of the 18th century and first years of the 19th century, farmers were undisturbed by mining the coal found on their lands. This was soon to change and resulted in many years of contention between landowners and the Legislative Assembly.New Brunswick became a separate province from Nova Scotia in 1784 and the seat of government moved from Saint John to Fredericton in 1788. The new province had its first priorities; the establishment of counties, the building of roads, and the development of its natural resources. From 1805, records of coal and land development are fairly complete. These records show the increasing interest of the Province in developing the coal fields. This interest resulted in the granting of coal leases to many friends of the government, without any regard for the wishes of the farmers who owned and had occupied the land for many years. The farmers fought back with lawsuits and other forms of dissension but with little success. By the end of the 19th century there were very few farm operators left in the area."

Jan 1, 1992

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By H. W. Manley

SULPHUR, like the minerals of coal, iron and petroleum, is one of the essential materials in our modern expanding industrial civilization. Before discussing the salient features of the production of sulphur from the Canadian sour gas, it seems appropriate to outline the historical past and probable future utilization of sulphur. The ancient Greek writer Homer spoke of its "pest-averting sulphur" and the "divine purifying fumigation". Ancient alchemists found sulphur to be a fascinating and baffling material. The discovery of gun powder in the year of 1250, and its application to the art of war a, century later, made sulphur an important commodity in the progress of mankind. The initial manufacture of sulphuric acid in the year of 1736 by the Englishman Joshua Ward, established the basis of a chemical industry that today utilizes 80 per cent of the consumption of elemental sulphur. Commercial production of the chemical soda ash ( N a2C03) discovered in 1787 by the famous Leblanc Process, in-creased international demand for the element sulphur and marks the birthday of the Sicilian sulphur industry.

Jan 1, 1961

By Joseph F. Daniels

In recent considerations of the utilization and beneficiation of coal, the chemise and the chemical engineer have been occupying the centre of the stage with their presentation of the picture of new fuel forms. The stage hands and supernumeraries of the cast, the miners and the consumers who carry the brunt of the present-day burdens, are apt to be forgotten in the glorious settings and the climaxes. With no thought of disparaging or of minimizing the efforts of our fellow scientists, let us remember that economic considerations as well as technical difficulties will limit these chemical applications, which must develop and move slowly before reaching the stage of industrial application at some later day. In the meantime, the coal-mining industry must live on hard faces rather than rosy dreams. In these brief notes it is my purpose to call attention to some of the physical advances in the utilization and beneficiation of coal which have been of interest to the industry in the State of Washington.

Jan 1, 1928

By R. S. McCaffrey

In addition to its importance in agricultural production, Wisconsin is a very large manufacturing state and its rank in the metal working industries is probably first among the States of the Union per unit of population. The University of Wisconsin is a state supported institution and the Wisconsin tradition has always emphasized the relation of the University to the state and its responsibility to exercise its leader-ship where it might, in any and every way, for the development and benefit of the state and the community. The Department of Metallurgy of the University realized its responsibilities in the carrying out of the co-operative tradition and, two' years ago, an experiment was started in co-operative research between the University and certain of the industrial plants of the state. At the present time this work has so far progressed that it is no longer an experiment, and its results prove that this co-operative research may be carried on very advantageously and that, under the conditions existing in the state, the method employed has been satisfactory.

Jan 1, 1926

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By Y. Chino

Cross-rolling, in which the roll axis is tilted by 7.5 degrees against the transverse direction, was carried out on a commercial magnesium alloy. The (0002) texture intensity of the cross-rolled specimen was lower than that of the unidirectionally rolled specimen. Also, the grain size of the cross-rolled specimen was smaller than that of the unidirectionally rolled specimen. As a result of the Erichsen tests at 433 ? 493 K, the press formability of the cross-rolled specimen was higher than that of the unidirectionally rolled specimen. The high formability of the cross-rolled specimen is attributed to both the reduction in (0002) texture intensity and the enhancement of grain refinement by the cross-rolling.

Jan 1, 2006

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By André Bérubé

"IntroductionSince the disappearance of Les Forges du Saint-Maurice at the end of the last century, many historians have taken an interest in the lengthy past of this enterprise. They considered the political, socio-economic, administrative and anecdotal aspects of the industry, but barely dealt with the elements of technology. The purpose of this article is to try to fill this gapru.Les Forges du Saint-Maurice was an integrated industrial concern, specializing in the production of semi-finished wrought iron and finished cast iron, that operated almost without interruption between 1734 and 1883. Les Forges first came into being in 1729, when Montreal merchant Francois Poulin de Francheville submitted to the king of France a request for the right to exploit the bog iron ore deposits on his seigneury of Saint-Maurice. This request, agreed to in 1730, was one of a long series of attempts, previously unsuccessful, to establish a local iron industry in the colony. Several such proposals were held up by a lack of capital from promoters or a too rigid application of the mercantilist policy by the metropolis. In 1730, however, the French minister Maurepas favoured a more liberal policy which would encourage private enterprise. The benefits of an iron industry to the naval construction industry was a factor that caught the attention of administrators. The choice of the site for Les Forges was based on the following factors:• the abundance of surface deposits of bog iron ore in the Saint-Maurice region;• the presence of a vast supply of hardwood and conifers needed in large quantities by this industry;• the proximity of sandstone and limestone deposits, indispensable materials for the construction and operation of the blast furnace;• the presence of a water stream, with sufficient flow to provide the hydraulic power needed for the operation of the machinery."

Jan 1, 1983

By J. C. Kurnia

Presence of fine dust in air causes serious health hazard for mine operators resulting in such serious problems as coal workers? pneumoconiosis and silicosis. Major sources of dust appear of course along the mining face where the minerals are extracted. Proper control and management are required to ensure safe working environment in the mine. Presented here is the use of a computational fluid dynamic (CFD) approach to investigate the flow and dust behaviour in mining tunnels. The objective of this study is to propose and examine various strategies to mitigate dust dispersion from the mining face and reduce dust concentration to a safe level for the operator. In a companion study, the authors investigated various methods for mitigating dust dispersion from the mining face to ensure safe dust concentration levels in the mine tunnel. Among the examined methods, implementation of brattice to direct the flow from the main airway to the mining face is the most effective method to disperse dust particles away from the mining face. The installation of brattice, however, will limit the movement of mine operators and vehicles in the tunnel. Hence, application of a hybrid brattice which is a combination of a physical brattice along with suitable directed and located air curtains is proposed and examined. Based on the CFD simulation results, over a range of parameters of interest, it was found that the physical brattice blocks the ventilation air and directs it to the mine face while an air curtain located along the brattice outlet offers flexibility in keeping the dust away from the operator allowing more freedom for the operator and the equipment. Results of the modelling over a range of parameters of interest are presented and discussed with the goal of managing dust concentrations within safe limits for the operator.

Aug 1, 2013

By G. M. Ritcey, M. Silver

"The processing of uranium ores produces tailings that could constitute environmental problems. At most operations the tailings are dumped into a designated area, with the ultimate acid drainage occurring if sulphides are present, together with the release of metal constituents to the rivers and streams. If the chemical reactions occurring within the tailings could be predicted, perhaps methods could be developed to either increase or decrease 'the rates of reaction. One such study has been in progress at CANMET during the past three years. The paper describes the use of Iysimeters containing low-grade and complex uranium tailings to determine the effects and interactions of bacteria, sulphides and solvent extraction organics on the release of radionuclides and on acid production. A simulated rain cycle nine-fold the normal was used and the Iysimeters were subjected to timed intervals of light and darkness. As a result, the tests simulated a 25-year period.IntroductionAlthough Canadians derive major benefits from uranium, there are environmental and health consequences, not yet fully understood, from the associated mining and milling operations. A major project at CANMET (Canada Centre for Mineral and Energ y Technology) has the ultimate goal of ensuring that any adverse effects on man and environment, now or in the future, resulting from the processing of uranium should be acceptably low. The magnitude of the task was exacerbated by the fact that the increased demand for electrical energy and the resultant increased prices for uranium oxide during the 1970s led to a rapid expansion in the industry. Annual world demand for uranium was expected to increase 12-15 fold in the next quarter century, with annual requirements of between 200,000 and 300,000 metric tonnes anticipated by the year 2000. Currently, the demand is low and the prices for the oxide have decreased."

Jan 1, 1982

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By A. Gakwaya, K. Ba, M. Guillot, J. Levesque

"In the aerospace industry, parts requiring tight dimensional tolerances and high mechanical properties are often produced by forging. This forming process allows for an optimal use of the material and can produce high quality parts at a reasonable cost. Thanks to CAD techniques, it is now easier to predict flow profiles and in-process defects occurrence as well as wear of the forging dies. However, in order to determine the properties of the forged part with computer simulation methods, a good material constitutive law is a prerequisite. This paper presents a virtual manufacturing process modeling for the closed die forging of a workpiece performed with Abaqus. The hot closed die forging is a regular process applied to manufacture metallic components used in aerospace industry. In this forming process, the material flow and final properties depend on the microstructure evolution during the process that is why it is important to include the microstructure effects in the material model. Based on the stress-strain data measured experimentally, the material parameters of the standard (classical) Johnson-Cook constitutive model and of a modified Johnson-Cook constitutive law including the microstructure effects have been determined. The obtained simulation results are compared with the experimental results for validation.INTRODUCTIONDue to their good physical and mechanical properties such as ductility, fatigue strength, corrosion resistance and rupture, aluminium alloys are often used in the aeronautic and the automobile industries. In this work, we present the forging of an Al-Zn-Mg-Cu alloy, a high strength aerospace alloy recognized for his good combination of physical and mechanical properties. The forging process is simulated in Abaqus Explicit using both the standard Johnson-Cook law (Johnson & Cook, 1983; Hor, 2011; Lin et al., 2012), and its modified version as proposed by Andrade et al., (1994). The Johnson-Cook law offers the advantage of considering the coupled effect of the plastic strain, the plastic strain rate, the temperature of forging and the hardening effect. However, it is a phenomenological model which does not account for the effect of the microstructure evolution. In this work, a modified Johnson-Cook model implemented in a user subroutine is used. It includes the effect of the dynamic recrystallization phenomenon during the hot deformation. The dynamic recrystallization has a noticeable influence on the microstructure and on the properties of the material. The term dynamic means that the process starts and acts during the deformation and this is different from the static mechanism of recrystallization which occurs during an annealing and after cold or hot deformation. Since properties of the alloy used in this work are not readily available in the literature then characterization tests have been done at various temperatures and strain rates, in order to determine the thermomechanical properties and the material behavior during the process of hot forming, more precisely during the hot forging process."

Jan 1, 2016

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By Robert B. Parsons

"This article addresses the relationship between mine evaluation, the tax system, and economic risk. It is based on a paper presented by the author at recent seminars in Moscow and Tashkent on the subject of mine evaluation.IntroductionTaxation can have a strong influence on the feasibility of a mining project. For the most part, because metal prices are determined on a global basis, the mining concern is not able to pass on to its customers any portion of taxes which the concern has to pay. Taxes are a direct charge against the project. The purpose of the article is to highlight the various ways whereby different taxes can affect the financial viability of a mining operation.The first part of the paper identifies different forms of taxation, and the second part of the paper addresses the different forms of taxation in terms of risk analysis and impacts on the mining project. Finally, the third part of the paper makes brief mention of using the taxation system to provide incentives with respect to investment in mining activities."

Jan 1, 1993

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959