Search Documents

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By Donald C. Craighead

"Overland conveyor systems to transport bulk materials from mines to processing plants or load-out stations have to be seriously considered as the viable alternative to truck and train haulage systems. With the ever-increasing price of diesel fuel, conveyors with their electrical drives generally prove to be the least costly when operating and maintenance expenses are analyzed for the life of the installation.IntroductionOverland conveyor systems are now considered as one of the viable alternatives which should be closely investigated when a mining company and its engineers initiate studies on methods of transporting raw materials from a mine to a processing plant or rail load-out station.This paper will generalize the overland conveyor and compare it with alternative handling systems. Each installation must be carefully studied to determine the best route, type of foundations river crossings; amount of excavation work for cut and fill, maintenance roads, etc. No two locations are the same nor are the principles of operation of an overland conveyor the same as those of a normal plant or mine belt conveyor. The proper time and effort must be put into the study of the system to evaluate the costs for comparison with other systems.The length of the overland conveyor depends on the layout of the mine and plant and the topography of the terrain between the terminals. Individual lengths may be up to 20 km, and a series of conveyors may extend 100 km or more.Advantages of Overland ConveyorsThe main advantage of overland conveyors is the low operating and maintenance costs which will be realized over its years of operation. Although truck haulage probably will permit lower capital investment during the initial phases of the mine development when the annual capacities have not developed to the design level, their operating and maintenance costs will be considerably higher. When evaluating the total costs per ton of material to be handled during the expected life of the operation and the projected increases for diesel fuel versus electricity, overland conveyor systems will generally prove to be economically more viable."

Jan 1, 1982

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

ONE of the morning sessions at the recent Annual Meeting was devoted to a Symposium on ways and means to expedite geological investigation, and also to promote greater prospecting activity, in Canada. It will be recalled that at the 1940 Annual Meeting, held in Winnipeg, a paper(l) prepared by Dr. G. A. Young, Chief Geologist of the Geological Survey, was presented, and was followed by a Symposium on Geological Investigations in Canada(2). On that occasion, the participants were in the main geologists, and they included the directors or other officials of each of the Provincial departments or bureaus of mines. At the Montreal meeting, the subject was discussed mainly from the point of view of the mining industry. The following pages present, in somewhat summarized form, the several contributions to that discussion.-ED. DR. J. J. O'NEILL(3), who was to have opened the Symposium, was unfortunately prevented through illness from attending the meeting. He had intended outlining the main features of his paper on The Exploitation and Conservation of Mineral Resources in a Balanced Development of Canada, presented at the last annual meeting of the Royal Society of Canada( 4). In his absence, DR.J. A. DRESSER presented a summary of the paper.

Jan 1, 1941

By Fazel G. Jahromi, Ahmad Ghahremaninezhad

Enargite (Cu3AsS4) is a major complex copper mineral and often is a carrier of invisible gold particles. Pyrometallurgical treatment of enargite is challenging due to the arsenic release to the environment. Hydrometallurgical treatment, on the other hand, appears to be a promising alternative for enargite processing. In an atmospheric enargite leaching process both the copper and arsenic from the mineral can be leached into a sulphuric acid solution and the arsenic can be simultaneously precipitated as ferric arsenate. The unlocked gold in the residue then can be recovered in a subsequent cyanidation circuit. The downside of the atmospheric enargite leaching in sulphate solutions is the slow leaching kinetics. In this study the effective parameters of the atmospheric enargite leaching process in ferric chloride media were investigated. All the experiments were carried out at temperatures below 100 °C. The process parameters that were investigated in this study included ferric, chloride, sulphate and cuprous concentrations, temperature, mixing rate and leaching slurry pulp density. It was found that the copper recovery rate increases with the addition of cupric chloride and also with raising the temperature. The highest leaching kinetics and the highest overall copper recoveries were achieved when cupric was initially added to the leach solution and at 90 ºC.

Jan 1, 2015

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, R. Pérez-Garibay, C. Jimenez-Velasco

A current problem in gold production is the presence of copper minerals which dissolve during conventional cyanidation practice. The dissolved copper causes several problems in the different stages of the process. This issue is the base for copper elimination/recovery methods such as the Sulphidization, Acidification, Recycling, and Thickening (SART) process, which is currently used in gold production plants around the world. Even though the process is well established, new challenges appear as the composition of the solution varies from ore to ore, in some circumstances affecting the performance of the SART process. This work presents a thermodynamic study and experimental tests performed to understand the role of the initial copper concentration and sulfur addition, on the efficiency of the copper removal. For a constant cyanide concentration, an increase in the initial copper concentration causes a decrease in copper removal; high sulfur/copper molar ratios favor copper removal. We demonstrated that the cuprous sulfide formed from solutions with high ionic strength, presents better sedimentation rates than solutions with less ionic strength. For solutions with low sedimentation rates, the use of some pretreatment is necessary to facilitate the sedimentation such as addition of flocculants, particle recirculation and the used ultrasonic pretreatment.

Jan 1, 2014

By J. E. Hawley, R. C. Hart

"The Preston East Dome gold mine is in the southeastern part of Porcupine district, Ontario, 5 miles southeast of Timmins, and immediately south of the property of Dome Mines, Limited.The claims now owned by this Company were originally staked in 1909. After the property had remained dormant for many years, the present Company was organized in 1936 to resume development operations. Two shafts had been sunk: at the time of the early work on the claims, but lateral work from these failed to reach the ore deposits. A successful diamond drilling campaign undertaken under the direction of D. G. H. Wright, however, was followed by the sinking of a five-compartment shaft arid the erection of a mill. From the start of operations to the end of 1944, 1,292,000 tons of ore averaging $11.60 in gold a ton have been mined.An outstanding feature in this mine is the occurrence of the major gold deposits in quartz porphyry intrusives, though minor deposits are also found in the adjacent Keewatin volcanics. Most of the ore occurs in fractures, but the filling was accompanied by varying degrees of replacement of schistose wall-rocks. The ore deposits may be classified as:"

Jan 1, 1954

By Christopher Andreae

Years before iron and steel works were established at Sydney, several thriving although short-lived iron works operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron works. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principal fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel works dominated production for Nova Scotia and the rest of Canada. Two sites achieved prominence in the nineteenthcentury Nova Scotia iron industry: Londonderry and Ferrona (Fig. 1). Londonderry, the larger and longerlasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace. But once the furnace was blown out in 1904, the population gradually drifted away.

Jan 1, 1999

By Cheng-Ting Chiang

Information integration and exchange for the entire building life cycle is one of the most important issues in the AEC industry. Although the Building Information Model (BIM) technology is widely utilized to address them, BIM is mainly concerned within the design and construction (D&C) phases. In the operation and maintenance (O&M) phases, however, the information integration and exchange issue becomes more complicated because software applications here require not only BIM but other information outside of the AEC domain, e.g., disaster mitigation. Nowadays, most BIM-related research focuses on the D&C phases and pays less concern on the O&M phases, hence there is a research need that can help seamlessly transfer the information between the D&C and O&M phases. In this research, a software framework using ontology was designed to deal with aforementioned problems. The BIM data from the D&C phases were used as a foundation to generate new models for different software applications for the O&M phases. The ontology technique was employed to assist the model transformation process between the original BIM and the models for applications. Finally, a disaster mitigation example was chosen to validate the framework, in order to make sure that the transformation process is comprehensive and useful from domain experts? perspective.

Aug 1, 2013

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By H. Vermette, J. Demers, R. Leclerc, P. Bergeron, P. Hudon, A. Lessard

The Arvida Smelter marked its 80th anniversary in 2006. Arvida currently operates 6 potrooms equipped with prebaked side-feeding pots producing 160 000t of aluminum per year, requiring the supply of 300 000t of alumina per year. In the past, to ensure reliable alumina supplies to the pots, especially in winter, a safety stock of alumina was kept inside the plant. The improved reliability of shipping on the Saguenay River has cut the need for such a stock. However, the stoppage of 8 Soderbergtechnology potrooms, starting in the 1980s up to 2003, generated alumina from the cleaning of pot pits, totaling 18000t and leading to the building-up of a significant alumina stock again. Concerns over working conditions, effect on potroom operations, and dust emissions prevented Arvida from tackling effectively this impressive alumina stock. Yet the increasing cost of alumina has created a strong motivation to use the stored alumina. In 2004 Arvida launched a project to recycle the stored alumina. This 4-year project aimed at clearing the alumina stock without affecting the operation of the smelter. It involved changing work organization, improving equipment and controlling the effect of the recycled alumina on the smelting process and working conditions.

Jan 1, 2006

By F. Richards

"The property of the Cariboo Gold Quartz Mining Company; Limited; is in the Wells-Barkerville district of Cariboo mining division. It consists of a group of 106 Crown granted mineral claims and fractions; and extends for over 6 miles along what is termed the Barkerville gold belt. The main portal and mine camp are half a mile south of Wells; which lies at the northeast end of Jack of Clubs lake and is reached by a 55-mile motor road from Quesnel; the northern terminus of the Pacific Great Eastern railway.Gold-bearing quartz veins were discovered on the surface in various parts of the property by different prospectors as far back as 1877, but the work that led to the formation of the present company was performed by Al Sanders in the year 1926. Sanders dug trenches and drove small adits on quartz veins containing gold above what is now known as the Sanders zone. Very little underground work has been done beneath the earliest known discovery-the B.C. vein. The Cariboo Gold Quartz Mining Company was formed in the autumn of 1926. The total production of gold from its beginning in 1933 to the end of 1944 has been as follows:"

Jan 1, 1954