Search Documents

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By P. Dyas, H. Zouitt, D. M. Smith

"Falconbridge Copper's Lac Shortt gold mine is located in northern Quebec approximately 300 km northeast of Val D'Or and 100 km west of Chibougamau (Pig. 1). Engineering for the mill commenced in early 1983 with a feasibility study. The plant was commissioned in the fall of 1984 at a capital cost of approximately $12 million. Design capacity was 750 tpd which was increased in the fall of 1985 to the current level of 1200 tpd.The ore at Lac Shortt is free milling, grading an average of 5.5 g/t gold which is finely disseminated throughout the host rock. Pyrite at 3 to 5% by volume and traces of copper mineralization are also present.Some of the latest gold processing techniques known at the time of design were incorporated into the mill. These include carbon-in-pulp, pressure stripping, electrowinning of pregnant solution and induction furnace refining. The plant also features several innovations such as a unique interstage carbon retention screen in the CIP circuit and the outdoor location of the cyanidation feed thickener, mill solution tank and reagent storage silos despite -40° Celsius winter temperatures.This paper describes the current mill process and discusses some of the problems encountered during the first two years of the plant's operation. CRUSHINGThe Lac Shortt surface crushing facilities are located in a separate building, isolated from the wet processing circuits for dust and noise control reasons. The crushing plant equipment was originally utilized at the Manibridge operation in northern Manitoba where it had been designed to operate at 135 tph. However, at Lac Shortt a rate of only 80 tph has been achievable to date, mainly due to the hardness and frequently slabby breakage characteristics of the ore. Therefore, in order to meet fine ore requirements at the current mill throughput of 1200 tpd, the crushing circuit is run seven days a week. 24 hours a day. Availability has been averaging 65%."

Jan 1, 1987

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

By P. Latostenmaa, T. Veneranta, J. Järvi, E. J. Peuraniemi

Boliden Harjavalta has operated a copper flash smelter since 1949 thus the smelter celebrates 70th anniversary of flash smelting in 2019. This paper shortly describes the historical perspective of the smelter and gives an update of the current operational issues and process modifications made during the recent years. The plant has carried out several major investments lately providing a firm view on the future. A new landfill area for the final slag was commissioned in 2018. A modernization of the concentrate storage area, a new acid plant and a debottlenecking project of the smelting line have been recently commissioned. At the same time, the tankhouse capacity will be expanded. This paper focuses on smelter modernizations. INTRODUCTION Boliden is a metal company operating mainly in northern Europe with core competencies in the fields of exploration, mining, smelting and metal recycling. Boliden Harjavalta, located in Finland, is part of the Smelters Business area of the Boliden Group and operates a copper and nickel smelter with related sulphuric acid plant in Harjavalta, and a copper refinery in Pori. As a short historical review, Harjavalta’s history may be dated back to the year 1910 when the Outokumpu ore body in eastern Finland was discovered. By the end of 1913, a copper mine was in operation and a copper plant based on Hybinette process was ready for commissioning. Due to difficulties in metal recoveries and throughput the Hybinette process was permanently shut down in 1929, and 100% of the mining production was sold as concentrate abroad. As the mine production increased steadily, a decision of a new smelter was made in early 30’s. In 1936 Outokumpu’s copper smelter based on electric smelting was commissioned in Imatra. The smelter was dismantled and transferred to Harjavalta during the final stages of the Second World War. The copper refinery started in Pori already in 1941 and the first copper anodes were cast in Harjavalta in 1945. First sulphuric acid plant started operation in 1947. Due to the post-war shortage of electrical energy, the plant metallurgists initiated a major development work to start exploiting the latent heat of concentrates. Thus, the flash smelting method was developed in Harjavalta and commissioned in 1949. Ten years later, flash smelting was also applied for nickel concentrates. Table 1 summarizes major historical and technical milestones of Harjavalta. The history of flash smelting is described in details in another paper of this conference (Jåfs et al., 2019).

Jan 1, 2019

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By T. G. Carter

"This paper traces the introduction and use of fire-resistant (FR) fluids in hydraulic systems at underground mines in British Columbia. Reasons are given for the decision to make compulsory the use of such fluids in underground mines after January 1, 1975 by provincial government legislation. Examples are quoted of fires caused, or supported by, mineral oils which have resulted in loss of life and property.The basic principles of hydraulic systems are reviewed in order to present the effects of changing a system operating on mineral oils to one which must operate on FR fluids. Approximations of the cost of system conversions are given for certain machines and a brief survey is made of the various pieces of underground equipment which contain hydraulic systems operating on FR fluids.IntroductionIn 1948, Admiral Ben Moreel , who was then president of Jones and Laughlin Steel Corporation in the United States , wrote:""Although safe and healthful working conditions can be justified on a cold dollars-and- cents basis, I prefer to justify them on the basic principle that it is the right thing to do. ""(1)This paper will outline the introduction and use of fire resistant fluids at mine operations in the Province of British Columbia. That it was the right thing to do in enhancing the safety and well-being of every person employed at the mines was the prime consideration. That it may be justified on a cold dollars-and-cents basis is left for the reader to judge. The prime purpose of this paper is not so much to trace the efforts made by the individual mines to successfully introduce and use fire-resistant (FR) fluids in hydraulic systems, but to present an over-all picture of what occurred, in a collective sense, at the majority of mines which have ended up with a working FR fluid system. The problems attendant to the introduction of an FR fluid will be recounted in a manner which, it is hoped, will prove useful to those contemplating system conversions. Because the predominant fluid now in use is an invert, or water-in-oil. emulsion, this will be the FR fluid considered.Fluid Loss from SystemsThe quantities of various fluids required for use in hydraulic systems are extremely high. This statement in itself may appear to be redundant in that the capacities of the various systems should demand that a fixed amount of fluid is required for the initial filling of a system, with a further amount of fluid scheduled for use during subsequent fluid changes, i.e. at the recommended change intervals . If only this were the case!"

Jan 1, 1981

By Douglas M. Smith, G. A. Maki

"The initial development of the massive potash deposits of the prairie evaporite formation took place over a decade ending in 1970. The potash mining and refining facility near Rocanvi11e, Saskatchewan was the 1ast of ten mines to come into production during that era. This operation, known as Sylvite of Canada Ltd., was designed to produce 1. 2 million short tons per year of KCl product in granular, coarse, standard and special standard grades.In 1977 the parent company, Hudson Bay Mining and Smelting, sold the Sylvite property to the Potash Corporation of Saskatchewan. Shortly thereafter PCS slated its new Rocanville Division for a two phase program of expansion. The first phase, completed in the spring of 1979, was relatively small, involving mill debottlenecking and additional equipment in the compaction circuit and the product and ore storage areas. The second phase was a major undertaking which included additional mining equipment and a new 300 STPH milling circuit. This work was completed during the fall of 1981 and has increased the Rocanville Division's nameplate capacity to two million STPY.Thickening equipment operating in the Saskatchewan potash industry is generally situated within the main refinery building or a separate insulated and heated structure due to the harsh winter climate and the need to closely control plant brine temperatures to ensure good flotation circuit performance. Since these thickeners process large volumes of slurries, conventional basin type designs tend to be large, ranging up to 150 feet in diameter or more. As part of the general effort to minimize capital costs, the potash industry has begun investigating the use of alternate high capacity, compact thickener designs. In this regard, PCS Rocanville undertook a program in 1978 to evaluate a Lamella™ Thickener and one other type of 'High Rate' thickener* as alternatives to a conventional design for the phase two expansion project."

Jan 1, 1983

By V. I. Ryaboy, S. A. Kondratyev

"The paper describes influence of desorbed species (DS) of a number of xanthates and higher dialkyldithiophosphates on the collective ability of these reagents. Adsorbed on mineral DS of the reagents in the form of products of non-stoichiometric interaction between xanthates and heavy metal salts can pass to the gas–liquid interface and remove liquid from the layer between mineral particle and water surface. A high-speed video recording displays the process of spreading of DS of xanthates and dialkyldithiophosphates over water at the moment of local rupture of the water layer. Expansion of “dry” spot on the mineral surface after DS of xanthate capture and displace liquid from the layer has been proved with video images. The comparative analysis of collecting ability and dynamic surface activity of dialkyldithiophosphates shows that these characteristics are in good correlation. The forces exerted by spreading film of the reagent’s DS on liquid in the water layer are evaluated, and the water flow rate from the layer is determined. The line of the reduction in thickness of the water layer behind the front of spreading film of DS of dialkyldithiophosphates and xanthates coincides with the line of the increase in their dynamic surface activity. Their force on the liquid volume in the water layer characterizes collecting ability of the DS film of xanthates and dialkyldithiophosphates. It has been supposed that the collecting ability of DS of a reagent is a part of its overall flotation activity, conditioned by surface tension of solution and, thus, defined by the structure of hydrocarbon fragment of the reagent.INTRODUCTIONIt is believed that collecting ability and selectivity of collecting reagents is mainly governed by adsorption of a reagent at the solid–liquid interface. A few studies have shown that activity of collecting reagents at the gas–liquid interface may have deep influence on their collecting capacity and selectivity. Experimental researches have revealed correlation between surface pressure in a carboxylic acid film on liquid’s free surface and floatability of useful components (Kulkarni & Somasundaran, 1975; 1980; Quast, 2006). According to Quast (2006), it is not always that surface pressure of a reagent film influences collecting ability of carboxylic acid. For instance, pH range of adsorption of tetradecanoic acid on hematite does not coincide with pH range of high surface pressure. So, surface properties of this acid contribute little to flotation efficiency.The correlation between reagent film surface pressure and mineral floatability has been reveled for quartz and cationic reagents, too (Bleier, Goddard, & Kulkarni, 1977). Finch & Smith (1973) showed that combination of adsorption of ion–molecular amine complexes on mineral surface and high surface tension of “fresh bubbles” was favorable for flotation performance. The use of bubbles with reduced surface tension resulted in a decrease in quartz floatability."

Jan 1, 2016

By Kaiwen Xia, Bibhu Mohanty, Per Svedensten, Sheng Huang

"The mechanics of crushing and grinding operations in mining and excavation processes has been investigated in a laboratory simulation study. It employs a multi-particle bedded rock target, which is subjected to multiple impacts. The impact set-up consists of a Hopkinson pressure bar and a Piston-holder system. The apparatus, employing a 38 mm diameter pressure bar, was used to apply varying but calibrated dynamic loading force on the rock particles. The energy consumed by the sample during fragmentation was determined by considering the energy carried by the incident wave and the reflected wave. The Pistonholder system is used to hold rock samples and to recycle fragments after each test for particle size analysis, for single as well as multiple impacts. The feed size selected was in the range of 9.5 to 12.7 mm for all rock samples, and the impact velocity was set at 14 m/s. Two strong granitic rocks and a relatively weak limestone were the target rocks. The resulting particle size distribution after each set of impacts, ranging from single to 10 consecutive impacts, were analyzed, and various size distribution functions (i.e. Rosin- Rammler, Swebrec, Grady and Gilvarry functions) were fitted to compare their suitability in predicting the fragment size distribution for each rock type. INTRODUCTIONCrushers are widely used in the mining industry all over the world. Understanding fragmentation behaviour of rock under crushing process is fundamental to improved productivity and efficiency in mining operations. This is particularly so as all subsequent size reduction processes such as crushing and grinding are far more energy intensive than the initial blasting process employed in breaking of in situ rock. A considerable body of experimental studies exists on the behaviour of rock crushers for specific rock types in order to aid in the design of various types of crushers. However, these studies are mainly site specific, that is, the results are largely empirical, and the fundamentals of fracture process that lead to size reduction have not been dealt with adequately. Most such studies have attempted to link the input parameters, such as feed size and crusher parameters, with output particle size, and global energy expended in the process. However the physical mechanism of crushing process is still not well understood. First of all, the energy consumed by the rock sample is hard to calculate during standard crushing or grinding tests; secondly, multi-particle test is hard to perform in the laboratory due to irregular shape of the subject rock sample. In This paper, describes a laboratory crushing apparatus for multi-particle rock samples, with sufficient control of the energy expended in the process, with a view to relate creation of new fracture surfaces in the size reduction process."

Jan 1, 2015

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

By K. D. Watson

"THE Mindamar zinc-lead-copper mine, owned by Mindamar Metals Corporation Limited, is at Stirling in Richmond County, near the south-eastern shore of Cape Breton Island, Nova Scotia (Figure I). It is connected by several roads with the Canadian National railway at Sydney and St. Peters.The deposit is said to have been discovered around 1895 as an outcrop in the bed of Copper brook, but the details are obscure. Not until 1925, when it was optioned by American Cyanamid Company, was it developed underground. Between 1927 and 1938, the 1-nine was operated intermittently by The British Metal Corporation (Canada) Limited, and yielded approximately 200,000 tons of ore averaging about IO per cent zinc, 2 per cent lead, I per cent copper, and small quantities of silver and gold. In December 1950, Dome Exploration (Canada) Limited made an agreement with Mindamar Metaî Corporation Limited, which was exploring the old mine, to assume management and prepare the property for production. Production started in April 1952 with a new mill and a new four-compartment shaft, and between that time and the end of 1954 it has totalled 545,347 tons of ore averaging 5·89 per cent zinc, 1·35 per cent lead, 0·66 per cent copper, 0·032 oz. gold, and 2 151 oz. silver.The Mindamar orebodies are irregular lenses and large veins lying within a wide, almost vertical shear zone of remarkable persistency. The shear zone consists mainly of well-foliated sericite schist derived from siliceous siltstone, and it contains a vast amount of dolomite and magne-site of hydrothermal origin. Most of the ore is extremely fine-grained and some of the high-grade material has a conspicuous thinly layered structure. The metallic minerals, in order of decreasing abundance, are pyrite, sphalerite, chalcopyrite, galena, and tennantite; the gangue minerals, in the same order, are dolomite and magnesite, quartz, sericite, talc, chlorite, barite, albite, and alunite.The geological setting of the deposit is shown in Figure 2. Except along streams and lake shores, almost all of the bedrock is concealed by glacial drift. The group of rocks in which the deposit occurs consists principally of greywacke, siltstone, tuff, brecoia, and Javas, and has been correlated lithologically with the Bourinot group of Middle Cambrian age. A short distance west of the mine, these rocks are in contact along the Stirling fault with conglomerate, arkosic sandstone, and quartzite belonging to the Middle River group of Silurian or Devonian (?) age, which elsewhere in the area overlies the Bourinot group unconformably. The large bodies of granitic rocks in the region, and the large lenticular masses of diorite and quartz diorite associated with them, have been assigned by Weeks (5, pp. 68-69) to the Devonian."

Jan 1, 1949

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By Jonathan Allen, Peter Radziszewski

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. The year 1948 saw the successful application of DuPont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding. In the context of the mining industry, smaller grain size and other mineralogical characteristics have motivated the need to grind finer. In order to address this need, the interest in stirred milling technologies has grown over the last 20 years as can be illustrated by the large body of literature published over this same period of time. The typical observation reported in the literature is that in certain circumstances stirred milling is significantly more efficient than ball milling. Despite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills. The aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of how power and energy is affected by stirred mill impellor design and mill operation. This will be accomplished by first completing an overview of the power models found in the literature followed by a general description of DEM and CFD stirred mill models as well as the insights that can be drawn from them. Finally, a generic stirred mill power model will be presented and applied to different stirred mill types in order to develop some insights into the differences between different mill types. The paper will close with a discussion on some of the challenges that these models have and how future research might contribute to overcoming them."

Jan 1, 2014

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By Chun-Sheng Liao, Chun-Hua Yan, Sheng Wu, Fu-Xiang Cheng

"INTRODUCTIONChina is providing more than 90% of the rare earth products consumed in the whole world. Acidic extractants are commonly used in the extraction separation of rare earths. Saponification of the acidic extractants by basic substances is usually necessary for the purpose of increasing and stabilizing their extraction capacity, and meanwhile inorganic acids are required for both scrubbing and stripping. Thus acids and bases are the main consumed chemicals, and the resulting salts are the main pollutants generated by rare earth separation processes. Currently, due to increasing environmental concerns in China, rare earth solvent extraction separation techniques are being developed to reduce both consumption and emission of chemicals, which is driving the developments on both theories and processes for solvent extraction separations.In the 1970s Prof. Xu et al. developed the Theory of Countercurrent Extraction (Xu, Li, & Yian, 1985). In recent years, the development of novel processes for rare earth separation has moved beyond the earlier theory. One rare earth separation process, the so-called hyperlink process, has been developed in the past decade and proven in industrial practice to dramatically reduce both the consumption and emission of chemicals during multi-component solvent extraction separations, and therefore is now widely used in the Chinese rare earth separation industry (Liao, Wu, Cheng, Wang, Liu, Zhang, & Yan, 2013). The present article will give a brief review of the development of the theory of the hyperlink processes, and the hyperlink separation flowsheets for typical rare earth mines in China designed using the theory.HYPERLINK PROCESSES (LIAO et al., 2013)A flowsheet of multiple-component separation consists of a couple of separation units. The units of a conventional flowsheet separately consume chemicals for saponification and scrubbing and discharge wastewater with resulting salts. In contrast, the separation units in a hyperlink process are hyperlinked and thereby the chemical demands of the whole flowsheet are decreased. For a feed containing t components of A1, A2, …, and At, it has been proved in theory that the separation mode of (AtAt-1…A2)/(At-1At-2…A1) is preferred in a single separation unit. The hyperlinking between separation units can have two forms. The link between two units locating at a same separation level, such as between (A4A3)/(A3A2) and (A3A2)/(A2A1), is known as horizontal hyperlinking. The link between two units located on different levels, such as between (A4A3A2)/(A3A2A1) and (A3A2)/(A2A1), is known as vertical hyperlinking. Both the hyperlinking forms have been proven to save chemical usage and consequently to lower the pollution emissions in industrial practices as well as in theory."

Jan 1, 2016

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992