Search Documents

By Ju-hyung Ha

New automated curing system for mass concrete has been developed to improve the quality of concrete structure and to save construction time and cost. The principle of this system is the automated water circulation system of heated curing water. Applied curing water on the surface of mass concrete keeps the temperature difference between center and surface of the structure below the threshold of specification. Mock-up test and field application have been conducted to investigate the performance of this system. In the results, new automated curing system reduced the chance of thermal crack occurrence and improved quality of the concrete structure as well.

Aug 1, 2013

By S. Esmaeili

The yield strength model developed by Esmaeili, Lloyd and Poole [1] has been adapted to model isothermal aging in Cu-containing AA6xxx alloys, with (a) a moderate and (b) a very low Cu content in the solution-treated, as-quenched, condition, Isothermal calorimetry has been used to analyze the kinetics of precipitation in these alloys, While the kinetic parameters for the low Cu alloy has been derived from the present experiments, the previously determined kinetic parameters for the high Cu alloy AA6111 has been used to model the precipitation kinetics in the moderate Cu alloy. The age hardening responses of both alloys have been well predicted by the model.

Jan 1, 2005

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By T. -W. Hong, Y. Son, S. -J. Hong, D. Choi

The characteristics of indium-tin-oxide (ITO) nanoparticles recovered from TFT-LCD panel scraps were investigated. The ITO was separated from TFT-LCD panel scraps by dissolving the color filter layer located between the ITO layer and the glass substrate. The solution was filtered to separate the ITO from the color filter component, and the filtered ITO was dissolved in the acid solution. ITO nanoparticles were then precipitated with ammonium hydroxide and organic dispersing agent, followed by heat-treatment at 600 °C. HRTEM, EDX and XRD analyses revealed that the 20 nm sized particle were composed of 90 % In and 10 % Sn, and were well crystallized to in the (222) preferred orientation.

Jan 1, 2014

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By G. Bourque

One of the design criteria for the Mount Wright facilities was to incorporate the latest proven automation techniques and devices for the new crushing, grinding and concentrating plant. The heart of the centralized control system is a Fox 1 process computer, located in the central control room in the administration building. The entire operation, i.e. crushing, conveying, storing, grinding and concentrating, is monitored and controlled, through the process computer , by one operator via a CRT console. In case of computer failure, the control is automatically, and without process interruption, transferred to manual back-up panels. One of the newest management tools, the process computer is programmed to collect and automatically print out shift. daily and monthly reports on tonnage, metallurgy and equipment operating time, for better planning of operations and preventative maintenance.

Jan 1, 1977

By S. A. Pence, A. I. McCallum, V. de Korompay

"Special salt protection rings containing a water-swell• able, polymeric sealant are in successful operation in Canadian potash shafts. Installed above the Prairie Evaporite salt formation at a depth of 3,000 feet, the sealant is preventing formation water migration into the salt and pressure build-up on the concrete lining of both production and service shafts. The salt protection rings are not under the hydrostatic pressure of the formation water.The chemical sealant in use has the unique property of imbibing water and swelling. •Therefore, any water at• tempting to flow by the seal ring actually produces a tighter seal.The purpose of this paper is to discuss the sealant and its properties and uses. Installation of the material and its operation in two Canadian mine shafts is described."

Jan 1, 1971

By M. D. Lawton, P. Steen

"Drilling results from the established levels at AngloRouyn Mines Limited had indicated inadequate tonnages to meet the planning schedule. It was decided to develop the main zone of the orebody below the bottom working level of the mine. The orebody dips north at an average of 50 degrees and plunges to the west at about 10 degrees. Due to the need for rapid development of this area, a decision was made to use trackless equipment.This paper describes the method used and highlights the use of small 5-ton diesel trucks as carriers for the 2-cu.yd LHD machine. The method achieved advances of about 1,000 feet per month, at a dip of 12 degrees over a length of close to 2,000 feet, using as few as 20 men per day."

Jan 1, 1971

By A. G. Eccles

Western Mines' milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine's location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines' alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977

By R. C. Bryce

"Selbaie is located northwest of Joutel, in what is known as the fourth east-west volcanic sediment group in northwestern Quebec. The main metals produced are copper and zinc, with important contents of both silver and gold. Production comes from an open pit mine on the A-I zone and from two underground mines on the B zone and the A-2 zone. Each mine gave rise to important capital investment programs for construction and mine development, all of which were managed and staffed with company-hired, non-union personnel. Production from all sources now exceeds 7000 tonnes per day, with a workforce of540 regular employees. Of particular interest technically is the high recovery of B zone reserves underneath 40 m of overburden cover, the low-cost capital development of the A-2 zone, the computerized control of open pit mining, and the successful copper-zinc separation of the A-1 zone ore. Due to the low grades of the mineral deposits, efficiency in all aspects of the production process, is essential to the success of the operation.LocationThe Selbaie Mine is located 82 km northwest of the locality of Joutel in northwestern Quebec (Fig. 1). Access to the mine is by an all-weather road, 32 km of which is paved. A second road access to the site is via La Sarre, 134km to the southwest. Employee access, materials transport and haulage of copper and zinc concentrates take place over both of these roads."

Jan 1, 1990

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By H. Feldheiser

Acid resistant brick linings are state of the art for anti-corrosion linings in tanks for high pressure acid leaching (HPAL) treatment. The design of these brick linings has to take into account the almost non-elastic behaviour of the brick lining inside a relatively highly elastic steel vessel. There must be tools and data available to determine for the steel vessels the thermal growth plus the pressure expansion and for the brick lining the linear thermal expansion and the chemical swell. Thermal shocks and pressure drops are not regular operating events but their negative influence on the lifetime of a brick lining has to be a part of the engineering study. Finite Element (FE) models as well as a lot of research and development on brick lining materials is the only way to find a path through the complex engineering work for pressure vessels.

Jan 1, 2004

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By H. Thomasson

This paper will deal with on-site maintenance welding using the stick electrode, electric arc process. It is primarily concerned with the underlying principles, the application of which, or the lack of such application, governs the success or failure of the operation. It will discuss first the base metal or item to be welded, including the field identification of its weld-ability and the determination of the procedures to be followed. Second, it will outline heat effects and the interrelation between heat applied as part of a welding operation and heat deliberately applied as part of a heat treating cycle, stressing the fact that in welding the same basic principles are effective. The third consideration will be weld metal and its control of both composition and properties. Last, but not least, distortion, shrinkage and residual stress will be considered and practical means for minimizing their adverse effects outlined.

Jan 1, 1967

By A. L. McAllister

"MASSIVE sulphide deposits are found in two areas of New Brunswick, the St. Stephen area and the Bathurst-Newcastle area. In both, the geology in the immediate vicinity of the sulphide bodies is largely inferred from drilling results as outcrop is not plentiful and is, in fact, almost lacking in most places. With few exceptions these deposits have not been explored by underground methods. Consequently much of the. detail on the geology will only become known over a period of years as economic conditions make mining feasible.Much of the information contained in this paper has been supplied directly by company geologists. As a result of the number of contributors, some confusion of nomenclature bas to be anticipated. Cross-sections and plans of the individual deposits are, in most cases, as supplied by the companies concerned. Most of the interpretations are the responsibility of the author."

Jan 1, 1960

By O. Worku, J. H. Masliyah, Z. A. Zhou

ABSTRACT The viscosity of concentrated kaolinite or illite clay in aqueous suspensions was measured in the presence and absence of a small amount of montmorillonite (<1 wt%). To avoid solids settling and to increase the sensitivity of the suspension viscosity measurements, solids concentrations higher than 38 wt% were used. The pH of the suspensions and the concentration of calcium and bicarbonate ions were found to significantly impact the viscosity of the clay suspensions. The results showed a significant increase in the viscosity of kaolinite suspensions with the addition of as low as 0.25 wt% of montmorillonite on a solids weight basis. In addition to illustrating the role of water chemistry in modifying slurry rheological properties, our study demonstrated that viscosity measurement could be a simple, yet sensitive technique for determining the content of smectite clays, such as montmorillonite, in a complex mix of various types of clay.

Jan 1, 2012

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967