Search Documents

By A. A. Iranzadeh

The performance of a tunnel boring machine (TBM) depends on the efficiency of the cutters, which can be influenced by geological conditions and rock mass properties. In this study, a three-dimensional numerical model, based on a discrete element method, was used to evaluate the effects of joint orientation and its spacing on the fragmentation process by a TBM cutter. Several models were constructed to study the effects of variable orientation; these models incorporated different spacing, variable spacing, different orientations on the fragmentation process, and different sections of the block model. Three parameters, consisting of induced tensile stress, induced shear stress and maximum displacement, were calculated. The stress in each section that forms chips was considered as critical stress; critical joint spacing and orientation in each section were determined. Results show that the critical orientation was in the range of 45 to 60º, where there was a possibility to achieve the maximum penetration rate. The critical joint spacing was 200 mm and, by increasing joint spacing, the value of critical stress decreased significantly. Furthermore, joint orientation could influence more than joint spacing in the rock cutting process.

Jan 1, 2009

By Si Qin

Unknown goafs and roadways of abandoned coalmines can be a great water inrush hazard for coalmine workers. Consequently, advance detection of such hazards is of great importance. By detonating seismic charges in underground coal seams, we can collect seismic data using a surface survey line, which is located across the ground projection of the underground shot point. This experiment was conducted in a coalmine in Shaanxi Province, China. After surface elevation compensation and travel time adjustments, we accurately determined the position of the goaf boundary along the survey line based on the wave velocity anomaly on the seismic record. Then we used a scattered wave imaging technique to enhance the energy of the scattered waves that are generated when the coal seam roof slide wave (refracted wave when the incident angle bigger than the critical angle) hits the roadway, thus confirming location of a geological discontinuity (roadway). This experiment shows that the coalmine ground seismic method, employing an underground explosive charge and a surface seismic array, has the ability to detect an abandoned roadway and goaf in advance of coal mining, thus can improve worker safety.

Aug 1, 2013

By R. Heikkilä

Today road construction sites utilize more and more information modeling in design phases as well as model based 3-D machine control systems in site operations. For main contractor, the management and control of all the site operations is a demanding task including also many challenges created by continuously developing new technology. In the paper, the main requirements for successful dynamic site management are introduced. The dynamic management means real-time possibilities for information acquiring, transfer and further utilization of the information in the management. An integration model to expand the current way of management and the utilization of present 3-D machine control systems is introduced. Different practical test results using two new different dynamic management systems are presented and evaluated. The first experiments and the results have been provided using the prototype system developed in a research project called DigiINFRA by the University of Oulu and Technical Research Center of Finland. Also, there have been tested a new commercial management system developed recently in Finland. In the conclusion, an expectation for the next generation for more dynamic road construction management methods is concluded.

Aug 1, 2013

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By R. Lanthier, A. Broussaud, J. C. Guillaneau, D. Hodouin

This study presents a method for upgrading the information extracted from the measurements given by the sensors of a pilot grinding circuit. For that purpose raw signals are combined to process models for extracting, through filters, the best information on the process state. Two different filters are used; one is based on steady-state mass balance constraints and the other one uses dynamic mass balance equations allowing for material accumulation in the equipment. The filters are designed and tuned with the help of a grinding circuit dynamic simulator and are then implemented in the pilot plant. Their performances and usefulness are discussed.

Jan 1, 1989

By Aimee Williamson

Bio-mining is a cost-effective, energy efficient and potentially environmentally protective method of exploiting a variety of ore deposits, from high-grade base metal deposits of nickel to lower-grade uranium deposits such as are found in the uraniferous quartz-pebble conglomerate beds of the Quirke Syncline, Elliot Lake, Ontario, using bacterial metabolic processes are used to enhance the solubilization of the metal(s) of interest. The cost effectiveness of bio-mining in Elliot Lake depends on the bacterially-influenced dissolution metals of economic importance, as well as on the ability to suppress microbiological activity following the release to solution of the economically important elements. This poster provides an overview of elemental recovery results and release kinetics for more than 50 elements. The data is obtained using a combination of advanced spectroscopic tools (ICPAES and ICP-MS) to analyze solutions obtained from a series of environmentally controlled biologically mediated uranium ore extraction experiments. The focus will be on rare earth elements, potential environmentally toxic elements, and metals of economic importance. Furthermore, the importance of these findings will be put into an economic and geologic context for the re-development of the mining industry of the Elliot Lake Camp.

Aug 1, 2010

By Chen Xia, G. Deschenes, Wan-Tai Yen

"Ammonium thiosulphate is a potential replacement for the cyanide in gold leaching. However, the high reagent consumption hinders its practical applications. In order to reduce the thiosulphate consumption, chemical additives were used. The gold leaching tests were conducted on a sulphide copper-bearing gold ore with 0.3M thiosulphate, 0.03M copper sulphate and 3M ammonium hydroxide solution at 44% solids and pH 10.2. Sulphate, sulphite, amino acid and chelating agents were initially used as additives. It was found that chelating agents (EDTA and NTA) could reduce the thiosulphate consumption from 30 kg/t to 17.8 kg/t with some increase of gold extraction. The improvement from other additives was not significant. Other approaches were also attempted to reduce thiosulphate consumption with some success. The thiosulphate consumption could be reduced to about 17 kg/t by reducing copper sulphate concentration fiom 0.03M to 0.0015M; adding 0.04M of EDTA; replacing copper sulphate with 0.001M of nickel sulphate. The increase of pulp density fkom 44% to 60% solids could reduce the thiosulphate consumption to 17 kg/t as well. Limiting the dissolved oxygen content by sparging nitrogen reduced the thiosulphate consumption further to 10 kg/t. It could be concluded that the regulations of copper and oxygen supply in the lixiviant were the keys to reduce the reagent consumption.INTRODUCTIONCyanidation, as the predominant gold leaching method, has been used in mining industry for more than a century. The low reagent requirement and the high performance are the reasons for its great success. However, cyanidation cannot deal with ores containing large amount of copper, nickel, arsenic and zinc minerals. This type of ore may consume more reagents and result in a poor gold extraction. On the other hand, the carbonaceous materials may preg-rob the gold from pregnant solution and make cyanidation a problem leaching method. Further more, the high toxicity of cyanide represents another challenge to modern gold mines. In the beginning of the year 2000, an environmental disaster caused by an accidental spill in Yugoslavia was broadcasted world-widely (Gurevitch 2000). Gold mine operators are facing higher social pressures and increasing costs on environmental protections. The usage of cyanide in mining industry has been banned in some countries and locations such as Czech Republic, Japan, Turkey, California, Colorado, Wisconsin and Montana States. Thus, a non-cyanide lixiviant is required."

Jan 1, 2002

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By V. Chatain

The environmental assessment of historical mining sites contaminated with various inorganic species, as also the determination of remediation targets require a better knowledge of pollutant-bearing phases. The objective of this paper was to investigate the operational fractionation of arsenic (As) in an As contaminated (ca. 3 wt%) soil collected from a gold mining site in France, where mining activities and smelting processes of gold ores took place until 2004. Single and sequential chemical extraction procedures were performed to evaluate the potential mobility of As according to the fractions to which it was associated in the contaminated soil, and also the part of As sorbed onto soil particles. These procedures used provided information on the nature of As fixation processes in the mining soil studied. Results showed that As appeared mainly sorbed (ca. 72%) with iron on the soil particles, in particular amorphous iron oxyhydroxides. These results confirmed a potential risk of arsenic mobilization under acidic and/or reducing conditions, which frequently occur in mining environment. This research evidenced the importance of the knowledge of As-bearing phases to better predict the mobility of this pollutant and in turn improve the management of As contaminated sites.

Aug 1, 2013

By Jean-Guy L. Gauthier

"With the Ontario Ministry of the Environment stipulating that the cumulative concentration of copper, lead, zinc and nickel in mine mill effluent must be no greater than 1.0 milligram per litre, it has become necessary for the mining industry of find some form of treatment for the removal of heavy metals from effluent waters.To comply with these guidelines, it became necessary for Mattabi Mines Ltd., which is situated 50 miles Northeast of Ignace in Northwestern Ontario, to develop a compact, cost effective and technically sound treatment process to remove heavy metals from their tailings overflow. A design committee consisting of mine metallurgists, environmental engineers, a Dutch research and development team and the equipment supplier engineering staff was set up to accomplish this.Using some new and innovative wastewater treatment equipment, the guidelines established by the Ontario Ministry of the Environment can now be met. The sludge produced from the precipitated heavy metals is sent directly to the concentrator, thus eliminating the danger of re-dissolution of the metals in a landfill site, while recovering some of the valuable metals that would otherwise be wasted in a sludge landfill."

Jan 1, 1980

"Abstract - An estimation of resources of structurally complex gold lodes and stockworks represents a challenging task for geoscientists due to the complex geometry of the lodes and discontinuous grade. In the present case study, the resource of a gold stockwork has been estimated by uniform conditioning after the lode has been subdivided into geostatistically defined domains using the indicator probability model. The indicator probability model represents a powerful tool for structural interpretation of the mineralization and can be applied when traditional 3D volume constraining methods (wireframing) have failed to produce a unique, non-subjective model. For comparison, the resources of the same zone have been estimated without domaining. Results of the study clearly show that estimates obtained without domaining of the mineralization can yield a substantial error due to excessive smoothing of the grade.Application of uniform conditioning for modelling the grade distribution has a significant advantage over linear methods (e.g., ordinary kriging). Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density without creation of biases or over smoothed local values."

Jan 1, 2002

By R. J. Rotzinger, K. W. Major

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By J. R. Morris

"A hoisting plant design should satisfy two basic requirements:1. to provide the necessary materials handling capacity, including ventilation where applicable, while meeting the requirements of good practice and, as a minimum, government regulation; and2. to optimize the economics of the project. Selection of hoisting equipment to meet the first objective is a complex but logical engineering process. The necessary calculations of payloads, accelerations, speeds, rope strength, hoist size, and power requirements are very readily carried out on computers or programmable calculators. A variety of hoist options can be quickly examined to assess the effects of changes in design parameters.Meeting the second requirement involves balancing the costs of various hoist arrangements and shaft designs, together with the time cost effects of differing shaft sinking rates and potential advances to be gained by concurrent level development. The proposed mine layout is significant here, as is the possibility of future shaft deepening and/or production increase. The availability of used equipment may be significant, both as regards first cost and delivery time. The factors are interactive, with their relative effects .varying from project to project. This paper sets out the primary factors to be considered."

Jan 1, 1990

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994

By G. Halverson, K. Blower

"Giant Yellowknife Mines Limited (Giant) has been producing gold since 1948. Located at Yellowknife, Northwest Territories, Canada, see Figure 1, the mine processes approximately 1,200 short tons per day of 0.23 ounce gold per ton of ore.The majority of the gold in the ore is sub-microscopic and associated within the mineral arsenopyrite. This association complicates the extraction method since straight cyanidation will only recover 30% of the gold. The operations at Giant involve four essential steps, with an overall recovery of 87%. The steps shown in Figure 2 are crushing and grinding, flotation, roasting and cyanidation. These processes result in a number of effluent waste streams characterized in Table 1. These streams are combined and sent to a tailings storage pond for subsequent treatment prior to discharge to the environment.Giant is located just north of the 62nd parallel where winter temperatures drop to -40°C for extended periods. This entails storing effluent in dams over the seven month winter period for treatment during the relatively short summer season.The treatment method currently employed at Giant is an ""alkaline chlorination-arsenic precipitation-flocculation"" process. The pond water is subjected to three phases of treatment prior to being discharged to the environment as shown in Figure 3."

Jan 1, 1987

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005