Search Documents

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By C. A. Petch

Abstract - The High Lake polymetallic deposit is located in the northern Slave province, 40 km south of Coronation Gulf, Nunavut. The main zone, the AB zone, hosts an estimated resource of 3.56 Mt grading 5.0% copper, 1.1% zinc, 0.06% lead, 1.7 g/t gold, and 18.2 g/t silver. Archean felsic metavolcanic and metavolcaniclastic rocks are the dominant rock type and are associated with lesser mafic metavolcanic and carbonate-rich metasedimentary rocks. The sequence strikes north-northeast, dips steeply to the west, and is truncated to the west by a large granodioritic intrusion. The mineralization at the AB zone is comprised of massive and stringer chalcopyrite-sphalerite-pyrrhotitepyrite± galena. At the core of the mineralized zone, intensely chlorite-altered rocks are locally metamorphosed to form distinctive zones of anthophyllite-magnetite-cordierite-altered rock. Peripheral to the mineralized core, alteration consists of sericitization, silicification, and weaker chloritization. Primary morphology and facing direction of the zone are difficult to interpret in part due to poor primary metal zonation of the deposit. However, the irregular shape of the mineralized zone and the erratic zones of zinc enrichment at the fringes are consistent with the interpretation that the zone was formed by the replacement of a porous volcaniclastic pile.

Jan 1, 2004

By Yu. V. Ponomarenko, A. I. Meka, P. A. Witherspoon, Yu. I. Volkov, J. E. Gale

"The mining of iron ore in the Kursk Magnetic Anomaly (KMA) region of the U.S.S.R. is done mostly by the open-cut method. An assembly of open pits capable of producing about 100 million tons of ore per year makes KMA the largest iron ore field in the world. Three gigantic open pits are currently in operation: Lebedinsky, Mikhailovsky and Stoilensky. These pits are as large as 13 km2 on the surface and as deep as 230 m. The mining operations are constantly faced with the problem of flooding from aquifers that overlie the orebodies; the magnitude of the problem is evident from the fact that the present groundwater inflow to these three pits is about 110 million mt /yr.Under such conditions, safe operations and pit wall stability are of great importance, and this has been accomplished very effectively by the appropriate use of seepage barriers and drainage systems. At KMA, the most important items used in the system of groundwater control are standard pumping wells, raise wells that drain into a 20 km to 30 km long underground drift located just outside the perimeter of the pit, horizontal wells driven through the pit walls, and horizontal drains. This paper describes the mining and engineering technology that have been developed at KMA to control the groundwater systems and protect the mines from flooding."

Jan 1, 1992

By K. Swedburg, M. Samuels

"The expansion of the concentrator at New Gold’s New Afton copper-gold mine in British Columbia, Canada, completed in 2015, included an increase in the required retention time of the cleaning circuit. On site pilot testing of a Woodgrove Staged Flotation Reactor (SFR) had shown that a high grade copper concentrate would be produced with excellent recovery. The SFR was selected rather than conventional tank cell technology based on the much smaller footprint (which rendered a separate and expensive building extension unnecessary), high concentrate grades demonstrated in testing, and the lower energy requirement. Three SFRs, each capable of taking a nominal feed of 700 cubic meters per hour were installed and commissioned 10 months after the receipt of order. The SFRs operate in series and all of the cells produce a final concentrate typically grading 32% Cu, while the overall SFR stage recovery averages 55%. The tailings from the SFRs are treated in the original conventional three-stage cleaner circuit where the remaining values are recovered in a concentrate grading 28% Cu. Design production was achieved within days of the initial start-up of the SFR circuit.INTRODUCTIONThe New Afton concentrator, located near Kamloops, British Columbia, Canada processes a copper-gold ore with a designed head grade of 0.96% Cu, 0.72 g/tonne Au, and 2.22 g/t Ag.The New Afton Mine is a block cave mining operation. Ore is undercut from the bottom up and removed at the extraction level from a grid of draw points. Ore is trammed to the ore passes by underground loader and dropped to a haulage level for transport by trucks to the gyratory crusher. From the crusher, the ore is conveyed to the mill via a 4.5 kilometre long conveyor system. Block caving was chosen for the New Afton deposit because the underground infrastructure could be built below the historical open pit of the Afton Mine (a previous operation of Teck Resources) and this method is favorable to large-scale low-cost mining.The New Afton deposit is a copper-gold, alkalic porphyry system. Hypogene mineralization is characterized by discontinuous copper sulphide veinlets and disseminations, principally chalcopyrite and minor bornite, along with pyrite as the second most dominant sulphide. Gold particles vary in size from 5 µm to 40 µm and occur as native gold and electrum, associated mostly with the chalcopyrite grains and never with the pyrite. In some instances, a second alteration phase has resulted in the copper sulphides being replaced by tennantite-tetrahedrite locally and along faults that transect the mineralized body. The design head grade of arsenic is 244 PPM, although the presence of tennantite is inconsistent and can vary from trace levels to 15% of the total copper. No arsenopyrite is present in the hypogene ores. Supergene mineralization, consisting of native copper with accessory chalcocite occurs in minor amounts along faults and highly oxidized near-surface portions of the deposit."

Jan 1, 2016

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By Jochen Petersen, Diane Taggart

"At an average of 90.3% (for the period of 1 January 2009 to 30 September 2011), Zincor’s zinc recovery was well below the industry standard of 96%. The losses through the residues, in particular the iron residue, were the biggest contributors to the overall zinc loss. It was believed that this loss could be decreased with the implementation of seed recycling. A plant trial was run to test the implementation of a seed recycle. The rate of seed addition through recycle was increased over a 4-week period. The presence of seed decreased the insoluble zinc loss by providing additional surface area for iron to precipitate onto, and reducing coating of unleached neutralising agent. The soluble zinc loss was also decreased at low and moderate seed recycle volumes. The improvement was attributed to agglomeration growth of the recycled particles, which improves the dewatering characteristics of the precipitate. In contrast, the soluble zinc loss increased at high seed recycle rates. This result was attributed to particle crowding and a low wash ratio.INTRODUCTION The Zincor refinery, which closed in December 2011, was situated just outside of Springs in the Gauteng Province of South Africa and employed the conventional Roast-Leach-Electrowin process, which accounts for 75 to 80% of the annual primary zinc production in the world. The refinery fed up to 220 000 t/a of zinc sulphide concentrate. The major portion of the raw material was sourced in Southern Africa from the Rosh Pinah and Black Mountain mines. Between 20 000 and 40 000 t/a of material was imported to make up the deficit and to improve the grade of the feed material. The iron contained in the zinc concentrates, at an average of 6.03% (for the period of 1 January 2009 to 30 September 2011), resulted in the formation of zinc ferrite during roasting, which is insoluble under atmospheric leach conditions. At Zincor, most of the zinc ferrite was dissolved in the residue treatment plant at elevated temperature and high acid strength. The leach liquor from this aggressive leach contained between 15 to 30 g/L of iron, mostly in the ferric form, and was known as the hot iron solution (HIS). The presence of iron in the liquor had an adverse effect on the zinc operation, particularly on the current efficiency in the electrowinning circuit. Therefore the iron needed complete removal."

Jan 1, 2016

By C. E. Baltzer

This paper highlights the position of coal supply in regard to the requirements for electric-utility operations. The text and the appended tables outline the trend of thermal power development and fuel use in the electric-utility industry. Mention is made of several argumentative factors influencing the use of coal in relation to competitive oil and gas, and of the importance attached to developing a realistic understanding of the respective problems faced by the supplier and consumer of coal. * * * TREND OF" THERMAL POWER DEVELOPMENT T HE RATE OF ADVANCE in thermal power has been significant during recent years, particularly in the Atlantic Provinces, the Prairie Provinces, Ontario, and British Columbia. While dependence on thermal power in Quebec and the Northern Territories is less than in the remainder of Canada, these regions also eventually will have need for increased amounts of such power.

Jan 1, 1961

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By S. N. Kalyakin, D. S. Flett, M. A. Mulagaleeva, N. V. Gudkova, S. S. Serdyuk, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina, V. G. Lomayev

"The Chuktukon niobium-rare earth elements ore deposit is located in Siberia (Russia). Weathered carbonatite crusts are the basis of the ore deposit. The deposit itself is 3.5 km in length, about 800 to 1400 m in width and up to 200–300 m in thickness. The ores are composed of iron-manganese oxides (hydrogoethite, hematite, psilomelane, pyrolusite) and contain 3–7% of rare-earth phosphates (florencite, monazite) and 0.5–1% of niobium oxide (pyrochlore). The ore is completely finely dispersed and consists of oxide particles formed of compact, dense aggregates which makes ore dressing as well as leaching of the rare and radioactive elements very difficult. Several options for processing of these ores have been considered: 1) reduction of the iron oxides to magnetite followed by beneficiation with magnetic separation to produce a rare metal concentrate; 2) processing of the rare earth elements (REE) containing minerals by direct alkaline-acid treatment; 3) processing of the ores using nitric acid leaching in an autoclave.INTRODUCTIONThe Chuktukon niobium-rare earth metal ore deposit is located in Siberia, in the Krasnoyarsk region, 110 km from the Boguchan hydroelectric power station which has recently been commissioned. This mineral raw materials is capable of providing impetus for the modernization of the Russian rare metal industry because of its qualitative and quantitative characteristics. The deposit is located in a region of promising industrial development and is a part of the territoriy where the Russian Federation’s Program “Complex Development of the Lower Angara Region” is currenly being realized. The main program directions are creation and development of industrial activities in sectors such as power, metallurgy, oil and gas, gold, rare-metals, and timber. The program will aid the development of the niobium and rare-metal resources of the Lower Angara and neighbouring regions as well as increase the national production of REE and therefore import substitution (Lapin, 1997; Lomaev & Kuzmin, 2003; Lomaev & Serdyuk, 2011; Serdyuk, Lomaev, & Kontorovich, 2000)."

Jan 1, 2016

By Yan Germain, Université Laval, Bernard Dallaire, Jocelyn Bouchard, Peter Radziszewski, Gilles LeBlanc, Michelle Levesque, Nicolas Tremblay

"The comminution process is estimated to be only 1% efficient, resulting in waste energy dissipated as heat, noise, and vibration. Energy recovery from grinding circuits has not been implemented mainly because recovering heat from the surface of the grinding mill or from mill slurry can impede operation, increase maintenance requirements, and prolong plant shutdown time (and production). However, currently very little information is available in the public domain regarding the amount of waste energy and that potentially recoverable in the grinding circuit of a mineral processing plant. Availability of such information could drive innovation and improve decision-making regarding opportunities for waste energy recovery. The Canadian Mining Innovation Council (CMIC) has initiated a study with CanmetMINING and mining industry partners to develop a model to map the energy flows in grinding circuits and to quantify the potential for energy recovery. The paper outlines the underlying fundamentals and data requirements for use in the model and then focuses on quantifying the energy recovery potential of the semi-autogenous grinding and ball mill circuits at the Agnico Eagle Goldex Division. Results show that most of the electrical energy (over 75%) is used to heat the slurry, leaving only a relatively small amount of it to achieve mechanical work (~9%). INTRODUCTIONCanmetMINING commissioned a study in 2013 to better understand the barriers for adoption of new technologies in the mining industry (MNP, 2013). The conclusions highlighted the importance of enhancing industry/regulator engagement and communication to raise awareness and improve the industry’s comfort level with new technologies.In November 2014, the Green Mining Innovation Advisory Committee (GMIAC) held a workshop to explore the possibility of accelerating the uptake of green mining technologies by bringing together key stakeholders among the mining value chain to address industry priorities. Participants included representatives from mining companies and associations, academia, provincial governments and federal departments and organizations. Two key priority areas emerged at the workshop: i) energy saving, and ii) water management."

Jan 1, 2016

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By T. J. Langan, M. Ramajayam, T. Dorin

"6xxx-series Al alloys are the most commonly used alloys in the automotive industry as they have an appropriate balance of strength, corrosion resistance and formability. The main strengthening phase in these alloys is the ß’-Mg2Si precipitates. One opportunity to achieve stronger 6xxx-series Al alloys, without affecting corrosion and formability, is the use of Sc. The main challenge of using Sc in 6xxx-series lies in the heat treatment, which must be designed to allow for a fine precipitation of both Al3Sc and ß’-Mg2Si. In this work, two model alloys are used, an Al-Sc-Zr and an Al-Mg-Si-Cu-Sc-Zr, to explore the impact of the 6xxx-series key elements (Mg, Si and Cu) on the Al3Sc precipitates. Transmission electron microscopy and atom probe tomography are used to investigate the precipitates present in the microstructure after casting. We find that higher Si content results in the formation of dispersoids upon casting. The average composition of these dispersoids is (Al0.8,Si0.2)3 (Sc0.888,Zr0.024,Mg0.08,Cu0.008). A closer look at the solid solution reveals that most of the Sc and Zr is supersaturated after casting even in the presence of Mg, Si and Cu. We discuss the impact of these results on the design of a suitable heat treatment for 6xxx-series alloys with Sc.INTRODUCTION The most common strategy to strengthen aluminum (Al) alloys is by micro-alloying to form a fine distribution of precipitates (Gladman, 1999). Whilst precipitates enhance the strength, this is often done to the detriment of ductility and corrosion performance (Davis, 1999). The 6xxx-series Al alloys are heavily used in the automotive industry as they offer an appropriate balance of strength, ductility and corrosion resistance (W. S. Miller et al., 2000). The strength increment in these alloys comes from the formation of the ß’–Mg2Si and the quaternary Q’ phase (Chakrabarti & Laughlin, 2004; Polmear, St. John, Nie, & Qian, 2017). One opportunity to achieve stronger 6xxx-series alloys, whilst keeping good balance of corrosion resistance and formability, is the use of small additions of scandium (Sc). Sc is one of the most potent strengtheners in Al alloys (Dorin, Ramajayam, Vahid, & Langan, 2018; Røyset & Ryum, 2005). Most of the strengthening benefits from Sc come from the formation of fine Al3Sc dispersoids. The following strengthening mechanisms apply to Sc: 1) Solid solution strengthening, 2) precipitation hardening, 3) inhibiting recrystallization, 4) assisting nucleation of other strengthening phases (Dorin, Ramajayam, Lamb, & Langan, 2017). As compared to other dispersoid phases, Al3Sc dispersoids have good electrochemical compatibility with Al alloys and hence do not affect their corrosion resistance (Cavanaugh, Birbilis, Buchheit, & Bovard, 2007). The coarsening resistance of Al3Sc is often improved by adding zirconium (Zr), as it forms a Zr rich shell around Al3Sc which prevents Sc from moving across the interface."

Jan 1, 2018

By Real Daigneault, François Robert, J. Paul Golightly, Jean-Yves Cloutier, Jayanta Guha, Pierre Pilote

"The Casa-Berardi East, Center and West deposits, located in the Archean Abitibi, Sub province, are hosted by volcanic and sedimentary units of varying compositions, less than300 m from the Casa-Berardi fault (CBF). The CBF, a brittle structure, represents an increment in the structural evolution of a regional-scale deformation zone showing ductile-brittle behavior known as the Casa-Berardi deformation zone (CBDZ). The CBDZ is characterized by a mylonitic Sc1 foliation which is folded a.n4 deformed by a later sczfoliation in high strain zones.Four generations of quartz vein and fracture systems have been recognized within the Casa-Berardi deposits. Most economic gold mineralization, occurring in the second generation system, is found within high strain zones. This system hosts three types of mineralized structures: (1) banded quartz veins; (2) swarms of veins and mineralized host rocks; and (3) disseminated sulphides along fractures. An early carbonate hydrothermal alteration zone (pre- to syntectonic) surrounds the deposits. Alteration associated with gold mineralization is contemporaneous to late ( syn- to post-tectonic) relative to the development of progressive deformation in the CBDZ. The geological characteristics and paragenesis of the four quartz vein and fracture systems developed as an integral part of the geodynamic evolution of the Casa-Berardi deformation zone."

Jan 1, 1990

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016