Search Documents

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By M. Sugamata

Creep tests were carried out for friction welded joints of AZ31 magnesium alloy rods under an ambient atmosphere at temperatures between 423 and 573K. Tensile tests were also performed at temperature from room to 573K. The obtained results were compared with those of the base metal. AZ31 extruded rods of 19 mm in diameter were joined by brake type friction welding machine. Creep and tensile specimens were machined out of the welded rods. The tensile strength of the joints was almost the same as that of the base metal at room temperature. However, joint efficiencies of welded joints were about 92% at above 373K. The elongation of welded joints was lower than those of base metal. The welded joints showed appreciably higher minimum creep rate and shorter rupture time than the base metal at all the tested temperatures and initial creep stresses. Creep and tensile rupture of the joints always occurred at near the weld interface. Thus, friction welded joints of AZ31 alloy showed lower creep and tensile strength than the base metal at elevated temperature.

Jan 1, 2006

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By O. A. Ojo, E. Anisimov, A. K. Khan

Electro-spark deposition (ESD) has recently generated a great deal of interest in processing aerospace materials. This is due to its potential for joining and repairing difficult-to-weld precipitation strengthened nickel-based superalloys without having problems of welding cracking that often plaque these materials. The short duration of current pulses involved in the process combined with the intermittent contact results in extremely rapid thermal cycle that produces nearly no heat affected zone in the substrate material. The microstructure of electro-spark deposited superalloy was meticulously studied in this work by scanning electron microscopy (SEM) and analytical transmission electron microscopy (TEM). The results show that in contrast to general assumption, the extreme rapid cooling rates involved in the ESD process did not produce partition-less solidification that is devoid of second phase microconstituents in the material. The secondary microconstituents were found formed along the intercellular regions of the solidification microstructure. The nature of these particles and the possible implication of their formation on mechanical properties of ESD processed material are reported and discussed.

Jan 1, 2015

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By J. Koponen, K. S. Stadler, A. Fuerst, S. Gaulocher, Th. von Hoff, R. Veldsman

"Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO).A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components:1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user.2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer.3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD.In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples."

Jan 1, 2012

By H. M. Howard

"The subject of Grinding Media is perhaps still quite controversial. Many people will state today that the spherical ball is the only way, and also will state that this was settled long ago others are not so sure, and I am in this second category. Over the years there have been many changes in grinding and in our evaluation of grinding media we should always be ready to review the overall situation at regular intervals. There is quite a lot of inertia in all branches of Hineral Dressing and this is particularly true of grinding or, more correctly, comminution.In order to understand some of the things which are done today, and to understand some of the thinking on grinding, it is desirable to go back some sixty years and trace the developments in comminution. In doing this we should consider perhaps three general categories with respect to daily tonnage. An arbitrary division would be under 500 T.P.D., 500-5000 T.P.D., and large operations which might have several parallel units, each with a capacity of about 5000 T.P.D. For the future, in the broad picture, this last category will be the important one because we will be more and more dependent on large-tonnage low-grade operations for most of the metals of the future. Some such division is necessary because the daily tonnage will have a very great effect on what we can and cannot do. It is also necessary to consider the entire flowsheet, and to remember in particular that grinding is not merely to make small particles but is also a conditioning process, to prepare the materi.al for the process which follows. The relationship of crushing to grinding must also be considered. It is logical to include the liners as part of the grinding media and we should try to distinguish between the wear of grinding media and the consumption of media by corrosion. Finally, the whole question of grinding media should be examined in relation to the possibilities of using some form of autogenous grinding."

Jan 1, 1970

By J. Ling, J. Xiao, A. R. Laplante

"The most challenging gold gravity separations occur when gangue has a high s.g., gold is fine, or a combination thereof This paper examines such separations, and evaluates the performance of a 3-in Knelson Concentrator at various rotation speeds, a 4-in SuperBowl, and a laboratory Mozley Multi-Gravity Separator (MGS). Synthetic feeds, primary cyclone underflows and flash flotation concentrates are tested.It is concluded that higher rotation speed are mostly useful for very fine (< 3 7 µm) gold recovery, with potential loss of recovery in the 37-212 µm range. This problem is traced to the collapse of the flowing film at higher Gs, which hinders the percolation of particles of intermediate size. Increasing fluidization water flow can alleviate this problem, but the recovery of very fine particle then drops. The MGS does not operate with the same principles, and can achieve good to very good recoveries of very fine to fine gold particles, but the unit has a high cost to capacity ratio, and there is no evidence yet that it can yield smeltable concentrate grade or a concentrate that can be upgraded with a shaking table.IntroductionThis presentation is a sequel to similar CMP presentations of the past eight years; all focused on practical aspects of gold recovery. The first hard rock application of the Knelson Concentrator (Laplante et al, 1990), studies of the grinding and classification behaviour of gold and other malleable metals (Banisi et al, 1991; Laplante et al, 1995), the development of a 3-in Knelson based methodology to study gold gravity circuits (Laplante and Shu, 1992), a comparison of the Knelson and Falcon (Laplante, Laplante et al, 1993), the presentation of a test to determine the amount of gravity recoverable gold, or GRG (Laplante et al, 1996), and the use of synthetic materials, in particular tungsten, to mimic gold (Laplante et al, 1995) were presented. A summary of many practical implication of the McGill research was presented in 1994 (Laplante). Whereas gold gravity recovery was less popular and largely jig-based (in North America) at the beginning of the eighties, many gold plants now incorporate a gravity circuit, and the Knelson Concentrator is the most commonly used unit."

Jan 1, 1998

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry&apos;s side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries&apos; own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By Michel Dagbert

"This paper illustrates the different ways grade-tonnage curves can be generated f or a mineral deposit. It emphasizes systematic discrepancies between reality, estimates and actual production according to different estimation methods and grade control programs. It does not offer a universal solution to the prediction of grade-tonnage curves. Hopefully, it will inspire caution to mineral economists who use estimated grade and tonnage data in the establishment of an optimum cut-off grade for a mining operation.IntroductionThe value of a mineral development venture often depends on a grade-tonnage curve. Statistics can help. The idea is to divide mentally the orebody into small blocks called selective mining units or SMUs. A SMU is an idealized version of the quantity of rock the grade of which will be tested against the cut-off at the time of mining. It could be as small as a truck load or a shovel load in very selective operations like some uranium mines where radiometric probing of each truck or car is performed. More typically, in an open pit operation, it will be the smallest zone flagged as ore from blast hole data, e.g. a 5 m by 5 m by 10m block, if blast holes are on a 5 m grid and bench height is 10m. Having defined the SMUs, the grade-tonnage curve determination amounts to evaluating the grade distribution of all the SMUs that can be mined in the depo sit. If we know this distribution we simply apply the cut-off to it and we get the number of SMUs above the cut-off (i.e. ore tonnage) and their average grade. .Assessment of the grade distribution of SMUs from exploration drill hole data is not an easy exercise and much has been published on the subject (David, 1972; Marechal , 1972; Huijbregts, 1975; Marechal, 1975; Guibal and Touffait, 1982). In this paper, we use a gold mine example to illustrate the influence of SMU size on the results. With the same example we also show that ""common-sense"" methods of grade-tonnage curve determination can sometimes be misleading."

Jan 1, 1987

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013

By T. B. Armstrong

"The energy situation is extremely fragile and there is a critical need for energy conservation in the short term and development of new technology in the long term. To keep tabs on energy flow, separate electrical metering is being installed in major industries: The first step reduces demand through peak load control; the second reduces the waste of energy by monitoring energy used per unit of production. IntroductionThe current energy situation is best described as being extremely fragile. The supply of hydrocarbons is being exhausted, while energy needs remain the same in the industrialized nations and are increasing in the Third World.The petroleum era is expected to come to an end in this century, as there will no longer be enough. Gas, coal and electricity will replace some oil as it becomes scarcer during the transitional period before new sources are gradually developed.There is a critical need for energy conservation in the short term. Conservation will, to a great extent be justified by savings, as it will be less expensive to recover energy that is being wasted than to acquire additional energy.The gradual development of new technology is expected to increase energy self-sufficiency in the long term. New energy sources are attracting a growing interest and are becoming more economically feasible and marketable. These rediscovered energy sources include peat, wood, solar, domestic waste and windmills.The sudden increase in energy prices has forced users to look at the way energy is used and find ways to save it. Major industries have found that using separate meters for each department spurs energy responsibility. Energy trim programs now rank in importance with profitability, productivity and with quality.Energy has become such a crucial cost element that better data are essential for planning. Data acquisition varies with plant size and number of utilities. Meters can be read manually or monitored by computerized energy management systems.The relationship of electrical energy input and production levels for a typical uranium mine will be used to demonstrate two steps to energy management. The first step reduces demand through peak load control; the second reduces the waste of energy by monitoring energy used per unit of production.The direct benefit of saving energy is the money saved."

Jan 1, 1980

By B. W. Clyburn

"Coals from the Corporation&apos;s Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing a/l essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.IntroductionVery high fluidity and unusually low ash are the outstanding characteristics of coal from Devco&apos;s mines in the Harbour seam of the Sydney coal field.However, sulphur content, mainly pyritic, ranges from 1 to 2.5070. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required .Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs.Typical data on the various coal properties of importance in the production of coke are included in Table I. Necessity of Low-Gravity SeparationThe design of any coal preparation plant requires the study of washability properties of the coal to be treated to determine the quantity and quality of coal produced at a given specific gravity along with the difficulty in accomplishing that separation.Their low ash content allows the important washability aspects of Harbour seam coals to be represented by sulphur! specific gravity curves (Fig. I). This particular example indicates that a yield of 54.5% is attained, at a sulphur content of 1.20%, for a perfect separating device operating with a 1.29 S.G. cut point.Material rejected from this separation still contains usable coal, which is recovered as middlings by separating at a higher gravity."

Jan 1, 1980

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980

By John Drew Ridge

"Over the years, ore geologists have made innumerable observations as to the relationships of certain kinds of ore deposits to particular types of rocks and to the types of primary and secondary structures that these rocks contain. On the basis of these, the places in which to look for new are deposits are more clearly defined than they would be in an exploration program based largely or solely on concepts of ore genesis. This paper discusses the affinity of certain rock types and structures for such ore deposits as: (1) tin-tungsten associated with granitoid rocks; (2) lead-zinc of simple mineralogy in carbonate rocks; (3) massive base-metal sulphides in sedimentary or volcanic rocks; (4) massive base-metal sulphides and oxides at, or near, contacts with igneous rocks; (5) gold or gold-uranium in, or adjacent to, conglomerates; (6) shale- or sandstone-hosted copper; and (7) porphyry coppers. Additional varieties could be considered, but it appears that these examples are sufficient to demonstrate the validity of the suggestion that the use of observational characteristics is far more useful in mineral exploration than that of theories of ore genesis.As by-products of the theory of plate tectonics, many concepts have been put forward to explain how ore deposits of different kinds have been formed. Most, if not all, of these theories seem to be as valid as present-day information permits. However, do these ideas add to the ability of the ore geologist to find ore deposits? I doubt it, and offer reasons as to why I think so.To produce maximum results in any exploration program, the one that makes the greatest use of information produced about the geologic environment of the area being investigated is the one that will provide the greatest return in deposits found for the sponsors of the program. Such exploration is best designated as total exploration, and it certainly is the most effective way of uncovering such new deposits as may exist in the area being studied in particular and of adding to the sum total of nonfuel minerals deposits available to the industrial world in general."

Jan 1, 1983

By G. Deschênes

The Eleonore property (James Bay district of Northern Québec), owned by Goldcorp, hosts gold within stockworks of quartz-tourmaline-arsenopyrite veins and veinlets contained within microcline (potassic alteration) and brown tourmaline replacement zones. The preliminary investigation to recover gold from drill core samples showed that flotation followed ultrafine grinding and cyanidation is the preferred option. Ultrafine grinding is used to liberate gold finely disseminated in sulphides. The flotation concentrate used in the investigation had a P80 of 11 microns and contained 75.5 g/t Au, 5.0 g/t Ag, 10.3% S, 0.07% Cu and traces of antimony (0.03%). The mineralogical characterization showed the presence of 65% gangue minerals, 23% pyrrhotite (hexagonal), 9.6% arsenopyrite, 2.2% pyrite and 0.08% chalcopyrite with trace amounts of galena (0.05%) and sphalerite (0.03%). Gold was in the form of native gold and electrum. A straight cyanidation conducted at pH 11.0, DO of 3-5 ppm, 2000 ppm NaCN, 20 C 72 hours extracted 97.0% Au and consumed 31.5 kg/t NaCN. The equilibrium was reached within 24 hours. Increasing the dissolved oxygen to 16 ppm reduced the consumption of cyanide to 22.0 kg/t with 96.7% Au extraction. A 16-h pretreatment with 2.0 kg/t lead nitrate, followed by a 24-h cyanidation reduced the cyanide consumption to 6.0 kg/t with a gold extraction of 97.5%. Increasing the lead nitrate addition to 6.0 kg/t reduced the cyanide consumption to 1.2 kg/t by passivating the surface of pyrrhotite. The gold extraction remained at 97.0%. It was possible to decrease the concentration of cyanide to 800 ppm NaCN without compromising gold extraction. The associated cyanide consumption was 1.2 kg/t NaCN. The passivation of gold grains was an issue when the cyanide concentration was decreased to 550 ppm NaCN. The gold extraction decreased to 92.2%. The average lime addition for all the tests was 7.4 kg/t and the average silver extraction was 80%. Efficient cyanidation of an ultrafine sulphide concentrate with only 800 ppm NaCN represents an advance in leaching of ultrafine sulphide concentrates.

Jan 1, 2013

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By W. G. Dallas

The social and environmental problems presented by the location of a large zinc/ lead ore body within one mile of a thriving town are described. The development problems are social, involving the education of the in habitants , and environmental, requiring the development of a planning strategy and the evolution of a baseline and post -operational monitoring system. The necessity for an environmental-impact assessment and a thorough baseline study is emphasized. The continuing psycho-social consideration of community reaction is advocated.

Jan 1, 1977

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011