Search Documents

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By J. F. K. Brown

WHEN I first received the kind invitation extended to me by the Mining Society of Nova Scotia, I read over very carefully the suggested title-"The importance of long-distance planning and budgetting in modern methods of mining, and the advisability of working to some definite plan". I came to the conclusion that I might as well confess my inability to handle properly such a vast and intricate subject within the scope of any one paper. More properly, I think a round-table discussion should be indulged in-a sort' of symposium carried on in similar fashion to the World Power and Coal Conferences- you know, a committee for this, a committee for that, and, finally, a committee to see what the committees are doing. Weil, your Secretary's suggestion is just like that- much too comprehensive for any half-hour's presentation. As a paper, also, it either becomes too general and therefore uninteresting, or i.t descends into detail and describes means and methods to the end desired, which have little attraction because they were designed to meet quite different conditions than those my audience would mentally be considering. Of the two evils facing me, I have chosen the one that sticks to the generalities. Your Secretary's query almost automatically divides itself into two distinct phases: First, the importance, and second, the advisability, of planning. Let us dwell for the moment on the second, because, if we can prove advisability, that leads to desirability and, finally, to doing. Proving is the difficult part of the little problem. Here was something I, personally and as a mining engineer, had been battling for all my corporate life without being able to prove it to anybody. Then I saw the way out of that. I perceived I could put that little question of advisability on another basis altogether-:put it in the class of "coming- some day- soon" whether you or l or anybody else liked it or not; call it, if you please, mandatory, certain, necessary, enforceable planning. All of which means that the problem of advisability has rather suddenly become the very practical one of "how to do it". Why?

Jan 1, 1937

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By C. Arson

"Optimizing hydraulic fracture injection parameters in order to maximize hydrocarbon extraction and to avoid extensive borehole spalling is still an open issue. In this paper, the Differential Stress Induced Damage (DSID) model is employed to simulate the anisotropic damage distribution around pressurized boreholes drilled in fractured shale. The loading path is purely mechanical: excavation and fluid injection are simulated by stress relaxation followed by pressurization. We investigate the effect of pre-existing fracture orientation, in-situ stress and injection pressure on the propagation of anisotropic damage during pressurization. Finite Element results indicate that (1) damage initiates and develops when the ratio of two in-situ stress component deviates from 1, and the magnitude of damage is proportional to this stress deviation; (2) For a given in-situ stress field, damage initiates for a certain threshold of injection pressure, and the damage zone extends as the injection pressure increases; (3) A pre-existing fracture only affects the damage zone locally; the orientation of that fracture does not affect the damaged zone, which is controlled by in situ stress and injection pressure.INTRODUCTIONHydraulic fracturing is used to increase shale permeability and to enhance hydrocarbon extraction. In order to maximize the extraction ratio and to avoid wellbore spalling and clogging during fluid injection, the parameters related to injection for each particular site need to be optimized. Therefore, it is necessary to clearly understand how shale responses upon excavation and pressurization.It is well known that breakouts grow in the direction of minimum compression and that plastic deformation around wellbores tends to arrest breakouts (Zoback et al., 1985). Laboratory acoustic emission tests revealed that fractures propagate along the direction of maximum compression stress, and fractures (breakouts) are surrounded by the Excavation Damaged Zone (EDZ), in which rock properties are weakened by the presence of micro cracks (Eberhardt et al., 1999; Martino et al., 2004). The anisotropy from orientated foliations and cracks may influence the development and propagation of fractures and breakouts (Everitt et al., 2004). Sonic televiewer logs proved that during hydraulic fracturing, fluid injection further alters the stress distribution (Evans et al., 2005). Shale natural fabric strongly affects the evolution of the EDZ around boreholes."

Jan 1, 2015

By P. Choquet, F. Miller

"The development and testing of a simple low-cost gauge for measurement of tension in a cable bolt grouted in a borehole are presented. Its principle is based on a resistance wire which is wound on a 70 cm length into the spiral grooves of the wire strand cable bolt. Readings are then taken by a robust automatic data logger with a several day autonomy or by a portable readout. In order to have a complete profile of tension along the cable bolt, a number of tension gauges can be installed along its length.This paper provides a description of the development and laboratory calibration of the tension gauge and addresses the two modes of loading for a cable bolt in a rock mass, namely pure tension and shearing at a joint location.In the second part of the paper, four field tests in underground and open pit mines are reported. The first test was used to substantially modify both the gauge and the readout unit principles while the other tests which are still on-going show a very satisfactory behaviour of the modified version of the tension gauge. IntroductionCable-bolting is often used as ground support in Canadian mines for a variety of applications. In underground mines, cable bolts can be installed vertically at the back of cut and fill stopes or in an inclined fashion in the walls of large open stopes. Alternatively, cable bolts at Mines Gaspe (Noranda Inc.) are used in a fan-shaped pattern from a drill drift to stabilize the inclined roof in 25 m wide open stapes. This new application oriented our research efforts toward the design of a novel instrumentation to monitor the efficiency of most commonly used 5/8-inch cable bolts."

Jan 1, 1988

By Euler De Souza, Kyle Penner

"Booster fans play an important role in assisting main fans by boosting the air pressure of the ventilation air passing through it. The correct placement of underground booster fans in a mine is a critical decision since it not only influences the mine’s operational capacity in terms of costs and efficiency, but also affects safety and environmental conditions. There are many booster fan installations around mines that are inappropriate, in some cases resulting in system failure (fan stall) or in a major negative impact on mine production. Inadequate booster fan placement has resulted, in some cases, in extensive air leakage which has compromised the economics of the operation and, in other cases, in recirculation of contaminants which has seriously compromised safety. This paper provides guidelines for proper design and siting of booster fans underground, to not only achieve an economic ventilation system but to create safe work conditions and efficient atmospheric conditions. Procedures for the planning, installation, operation and maintenance of booster fans are also presented. A case study illustrating the design and siting of a major booster fan installation in a potash mine, supported by computational fluid dynamics analysis, is presented.INTRODUCTIONIn large underground operations with complex ventilation networks offering high resistances, the never ending increased required quantities of air can almost only be supplied through use of high pressure main fan systems. These fans may, in effect, induce significant leakage losses in the system, having a negative impact on safety performance. In such cases, booster fans can be designed to decrease the main fan pressures and reduce the leakage flows, improve system efficiency and reduce costs. In well designed systems, booster fans can thus be used to redistribute the airflow and assist the main surface fans.When the pressure supplied by the main fans is insufficient to meet the ventilation circuit pressure requirements, booster fans are placed in strategic locations where pressure boosting is essential. Booster fans are typically sited in sections of the circuit offering high ventilation resistance and requiring this form of ventilating air motivation. Booster fans are thus required when the mine expands, and so the resistance of the ventilation network, and the primary fans no longer can supply the required pressure and flow."

Jan 1, 2019

By E. G. Joe

"This paper summarizes the main conclusions derived from twenty-two technical presentations made at the 1973 meeting of the Canadian Mineral Processors. Results of two surveys with response from over seventy mines were reported on Canadian milling practice for water re-use and on elimination of cyanide from mill effluents. Water and solution recycle in Canadian mills were detailed for copper, copper-zinc, lead-zinc-copper, nickel-copper, iron and gold mines. Cyanide elimination from mill effluents was reported under current practice and under requirements for further treatment by various other processes. Three recent process equipment entries into Canadian mills have been the on-stream particle analyzer, the new gravity concentration tables for recovery of fine tin and other heavy minerals, and solution-jet slurry equipment for reclaiming ground ore from storage. The principles of operation of this equipment were described along with the practical limitations that were found in their application to mineral processing. Capital costs and milling cost reductions were shown in some operations. Computer control of flotation mill processing was a major item on the program. Four major mining companies outlined their mill process control strategy, computer programs and on-stream analysis equipment. Some capital costs and personnel changes were presented, together with gains in concentrate grade and mill recovery. Recent development work has shown the effect of the type of grinding and of aeration on the recovery of sulphide minerals in flotation. One mining company reported a significant depressing effect on copper sulphide flotation while floating ore ground with mild-steel balls; also, pyrite appeared to be activated in the subsequent zinc flotation step. One company with extensive experience in the application of aeration to copper sulphide flotation showed significant improvement to copper recovery by pre-aeration. Both the effects of grinding and aeration were subject to the constraints of the chemical condition of the ore pulp. The metallurgy of silver recovery by combination grinding - gravity treatment and of gold recovery from a complex gold-sulphide ore were reviewed in two papers on precious metals. The latter paper further described the recovery of gold from the Cottrell collectors and the final disposal of arsenic from the dust collectors."

Jan 1, 1973

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

By S. N. Aliferova, E. I. Afonina, S. N. Titkov, A. Ju. Bondareva, N. N. Panteleeva

"Potash ore is mainly processed using the method of cationic flotation. Potash ore deposits of the CIS, namely: at Upper Kama river, Gremyachinsk (Russia), Starobin (Belarus), Tubegatan (Uzbekistan) are characterized by relatively low KCl impregnation (1.0 – 1.5 mm) and contain up to 10% of waterinsoluble impurities (WII). Water-insoluble impurities are presented by aluminosilicate, silicate, carbonate (calcite, dolomite) minerals and anhydrite. In the process of milling the ore to a flotation size there are released and dispersed the insolubles impurities actively sorbing the cationic collector, i.e. aliphatic amines C16 – C22. In this regard there is carried out a preliminary desliming of the ore.Currently grinding the ore to a flotation size (1.5 mm or less) is carried out in rod mills along with forming of a large number of fine-grained ore fractions having the size under 0.25 mm, which results in the increased KCl losses with halite slime waste and reduction in the quality of finished product. There has been developed the technique for processing of potash ores with a high content of water-insoluble impurities (10 – 12%) containing, in different ratios, silicates, carbonates and anhydrite. The technology involves the use of the ore dry grinding to the flotation size and subsequent reagent activation of the processes for sludge removal and sylvite flotation.INTRODUCTIONCurrently there are being developed the potash ore deposits in the CIS countries, namely: at Upper Kama river and Gremyachinsk deposits (Russian Federation), Starobin deposit (Republic of Belarus) and Tubegatan deposit (Uzbekistan). Potash ores are a mixture of sylvite and halite and contain water-insoluble impurities of silicates, carbonates and anhydrite. The content of water-insoluble impurities (WII) reaches up to 10%, disseminated (impregnated) sylvite does not exceed 1.5 mm and in connection with that the ore is crushed to a particle size under 1.5 mm. Ore grinding is performed by wet process in rod mills with producing a significant amount of fine-grained mineral fractions and sludge, which are actively sorbing a cationic collector, i. e. primary aliphatic amines C16 - C22. The ground ore is deslimed and the slime product is directed to a sludge depot (pits)."

Jan 1, 2016

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By John Oxenford

There are currently two operators producing oil from the surface-mineable portions of Alberta?s oil sands (Syncrude Canada Ltd. and Suncor Inc.) and two other companies are proposing to enter the industry (Albian Sands in 2002 and True North in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of recoverable TiO2 and approximately 80 000 tonnes per year of recoverable zircon. This represents approximately 6% of the world?s TiO 2 consumption and approximately 9% of the world?s zircon production. With the commissioning of plants by Albian Sands and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in Alberta?s oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widelyheld suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers: 1) The bitumen coating on the sand grains; 2) Secondary mineralization such as pyrite, siderite and calcite 3) A high proportion of aluminosilicates (approximately 25%) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier. The pyrite can be removed by flotation. And the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

May 1, 2001

By T. Gonzales, S. Thakurdin

The conducting of risk reviews is an essential activity in ensuring safe operating conditions, both during project design phases and for existing facilities. The following paper presents a structured approach to the conducting of risk reviews for existing operations, including descriptions of supporting documentation and guidelines for on-site review activities. The conducting of regular site risk reviews and safety audits is crucial in ensuring the continued safe operation of existing facilities, particularly in the copper industry where numerous processes and unit operations can present catastrophic risks, both in terms of loss of life and financial liability. The structured approach presented aims to provide a logical and comprehensive analysis of risks to align safety-related facilities and procedures with current industry best practice and ensure consistency across multiple client operations. INTRODUCTION The production of copper, whether by pyrometallurgical or hydrometallurgical process routes, carries significant inherent safety risks. Production volumes are relatively large, often requiring complex processing routes, multiple production trains and a variety of supporting ancillary facilities. Furthermore, considering the relatively large size of ore reserves, copper production plants can have operational lives well beyond the typical design duration of 20 years. In this context, the conducting of regular risk reviews is essential in ensuring safe operating conditions and aligning facilities with current industry best practices. Risk reviews and safety audits can take various forms and have various areas of focus. The methodologies and approaches described below relate specifically to catastrophic risks, defined broadly as risks that carry the potential for multiple fatalities and significant financial losses. Focus is given to existing facilities and does not consider the risk-related activities such as hazard and operability (HAZOP) studies conducted during plant design. The structured approach presented aims to provide a guide for effective site- based audits and a logical analysis of risks identified. RISK CLASSIFICATION Table 1 provides a typical summary of the classification of risk types and the associated consequence categories and descriptions. It illustrates the descriptions of a catastrophic risk in terms of the broad categories of Health & Safety, Environment, Financial, Image & Reputation and Legal & Compliance. In terms of the Financial category, numeric costs ranges are often prescribed depending on the financial characteristics of the specific operation and the associated parent company.

Jan 1, 2019

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By Jean-Yve Tremblay, Michel Prud'homme

"IntroductionIndustrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors.At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2.Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties.The Industrial Minerals Industry in CanadaCanada has a large industrial minerals base and is a world leader in the production of some of them. The total value of product ion of these minerals has grown by 115% over the last 10 years despite the misfortune of asbestos.Industrial minerals have shown remarkable growth in the past 20 years at an average annual rate of 9.2%, compared to 7.8% for metallic minerals. In 1986, the value of industrial minerals rose to $4.9 billion, or 14% share of the Canadian mineral production. Figure I shows the value of production of the mineral industry for the period 1966-1986.The leading segment in industrial minerals segment since 1976 is the chemicals and agro-chemicals sector which has an average annual growth rate of 5.75 % in terms of value of production. During the same period, the growth rate for the whole Canadian mining industry was 1.37% per annum. The chemicals and agro-chemical s sector increased its contribution to the total value of production of 2% to 6070 despite the growing share of fuel minerals with 59%."

Jan 1, 1988

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982