Search Documents

By R. D. Brown

For the first time in years, the spring budgets of federal and provincial governments have not brought down major new proposals affecting the tax burdens of the mining industry in Canada. It seems appropriate to use this unaccustomed period of tranquility to set out an extremely abbreviated summary of the principal features of the federal and provincial income and mining tax rules affecting the mining industry.

Jan 1, 1977

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By David Green

"This paper describes Outokumpu's Tank Cell concept using the unit reactor principle and operating experience gained in various applications. Presently the tank cells used range in size from 35 t pilot size to 100 m' (3500 cuft). The paper discusses operating experience and results from commercial installations in copper and zinc rougher and cleaner services.The key feature of the Tank Cell described is the effective control of the froth phase and resulting possibility to operate on an improved grade recovery curve by manipulating the control variables."

Jan 1, 1995

By K. Pienimäki

Boliden Harjavalta Oy has produced copper since 1945. The essential idea has always been continuous development of process efficiency and environmental friendliness by using the Best Available Techniques (BAT). The ongoing development step is to increase the production capacity up to 210 000 tpy of anode copper and 155 000 tpy of copper cathode. One of the focal issues in this action is modernization of the copper refinery to utilize permanent cathode technology. This paper describes the refinery project and the technology used in it.

Jan 1, 2007

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

By James Pirie

"The major Archean gold deposits in the Red Lake greenstone belt, which have produced over 374 million grams of gold since 1930, occur near the top of the lower komatiitic to tholeiitic mafic to ultramafic metavolcanic sequence. The upper calc-alkalic mafic to felsic rocks form three discrete and separate ediftces overlymg this lower sequence.The gold deposits are classified according to their stratigraphic or lithologic associations into:1) mafic-volcanic-hosted deposits;2) felsic-intrusive-hosted deposits; and3) stratabound deposits.Group 1 and to a lesser extent Group 2 deposits occur within zones of alteration several square kilometres in extent. The nature of this pervasive alteration can be characterized by comparison of petrochemical data from the altered rocks and their fresher equivalents some distance away. The altered rocks have substantial addition of SiO2> CO2, K2O, As and Sb and subtraction of Na20, CaO, MgO and total Fe. Cr, Ni, Co and Zr appear to have been relatively immobile. Hydrothermal alteration and gold deposition probably accompanied early fumarolic activity and continued during subsequent deformation the metavolcanic sequence, with gold eventually being mobtltzed and concentrated into major vein structures to form the present orebodies. The smaller Group 2 deposits formed by emplacement of felsic intrusions into already altered, anomalously gold-bearing mafic metavolcanics, with the heat from the intrusions setting up parasitic hydrothermal systems which mobilized the gold and deposited it along with minor sulphides in fractures in the cooling intrusions."

Jan 1, 1982

By Paul E. Lamoureux

Introduction The Author As the pail of smoke and wartime destruction gradually rises from the surface of the earth, from all countries, statesmen assemble to discuss and prepare pacts and treaties which are designed to, once more, bring people of all nations to understand each other and live in harmony. Scientists and engineers throughout the world are also undergoing a drastic reconversion in their ideas and objectives. No longer do they think only in terms of destruction and twist their brains to develop more devastating weapons or to surpass production records of war machinery. They have turned their eyes and ambitions to more pleasant tasks and are taking stock of wartime developments in materials, fabricating procedures, and equipment, many of which had been carefully shrouded with a veil of secrecy, and are applying their new knowledge to the fabrication or improvement of the tools of peace. The next few years will see the gradual elimination of scores of substitutes and makeshifts, expedients which the constantly changing law of supply and demand' under wartime stress necessitated. The universal search for satisfactory substitutes, however, has resulted in a general awakening of plant engineers to the possibilities of materials with which they were relatively inexperienced, with the result that, in many instances, what was considered a substitution at the outset turned out to be more satisfactory than the original material, and, in reality, can be considered a worthwhile development. Not only have materials been explored, but existing fabricating processes have been reviewed, and others, built around the properties and characteristics of new materials, created.

Jan 1, 1947

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931

By F. A. Forward

"IntroductionTHE LYNN LAKE MINE, situated in Manitoba about 150 miles north of Sherridon, has been actively developed by Sherritt Gordon Mines, Limited, during the past seven years, resulting in the establishment of a proven reserve of over 14,000,000 tons of ore containing 1.223 per cent nickel, 0.618 per cent copper, and additional cobalt values. For many years, the Sherritt Gordon Company operated a copper-zinc-gold mine at Sherridon but, as this mine was approaching exhaustion and as it was proposed to use the mining and milling equipment to treat the Lynn Lake ore, a number of unusual problems were faced in transferring plant and operations from the one mine to the other, and particularly in preparing to undertake nickel production.Preliminary investigation showed that the ore could be concentrated by flotation to produce a copper concentrate containing 28 to 30 per cent copper with less than 1 per .cent nickel, and a nickel concentrate containing 11 to 14 per cent nickel, 0.3 to 0.4 per cent cobalt, and less than 2 per cent .copper, with high recovery of the three metals in .the concentrates. It was apparent that, initially, the copper concentrate could be economically smelted and refined in the usual manner. But as the nickel concentrate contained an insignificant amount of precious metals (less than 0.02 oz. per ton) and as .it had a much higher nickel content than comparable concentrates normally produced from sulphide ores, the selection of a treatment process and the location of a plant required careful study."

Jan 1, 1953

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By C. E. Rodgers

WHEN the writer was engaged early last year by Canadian Comstock and its subsidiary, the Metropolitan Electric Company, to act as Consulting Mining Engineer in connection with the layout and equipment of the new ore-dressing laboratories at Laval University, Quebec, the metallurgical laboratory section of the School of Mines building was completely erected, including plastered walls, partitions, etc., and finished concrete floors. At that time, however, no equipment had been ordered, except three Dominion ball-mills and two Bell screening machines. ADVANCED OR CONTINUOUS LABORATORIES The continuous laboratory section of the Department occupies the basement and three floors of the building, with an approximate floor area of 9,000 square feet. Because of limitations imposed by the design of the building (height and arrangement of rooms, strength and design of floors, etc.), modifications of layout from what otherwise seemed most desirable were, of necessity, made. These included: (a) Omission of automatic sampling of the dry ore. (b) Complete elimination of inclined belt-conveyors through floors. (c) Exclusion of bucket elevators for either dry or wet ore transfer. (d) As a substitute for grill-covered drains and floor sumps, drainage from sections or from individual pieces of equipment was piped to a disposal system in the basement. (e) Substitution in several instances of fabricated steel in place of the usual concrete foundations for machinery. (f) Reducing floor cutting and area of such opening to a minimum. Ore storage and chute capacity above the basement level was also minimized to reduce total weight.

Jan 1, 1941

By W. M. Williams

"Although manganese is a metal virtually unknown to the layman, it is hardly necessary to point out to the engineer the importance of manganese in modern metallurgy, an importance intimately linked with iron (and steel), the basic materials of engineering construction for hundreds of years and certain to remain so for long into the future. World steel production will approach and perhaps reach 1 billion tons/year in the 1980s; with a manganese content between 0.5% and 1 % in ordinary steels, and more in specialty steels, manganese use worldwide will soon approach 15 million tons annually. Manganese was discovered and isolated in Sweden in 1774 by Karl Wilhelm Scheele (who also discovered molybdenum), but the element was only of scientific interest for several decades. By the early part of the nineteenth century, however, manganese oxide had become commercially available and was in use for colouring glass and for the production of chlorine. Commercial application in metallurgy appears to have been limited to the manufacture of crucible (or ""cast"") steel, a highquality product made by carburizing wrought iron, and melting it in small batches to make ingots which could be rolled and used for special applications, e.g. for the manufacture of fine tools or for ""steeling"" the cutting edges of implements such as wrought iron axes and chisels.* However, it was not until Bessemer's epoch-making invention of cheap steel in 1856, and the dramatic expansion of the steel industry thereafter, that manganese assumed the importance that it holds in modern steelmaking."

Jan 1, 1999

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By R. A. Hemstock

"OIL EXPLORATION in Western Canada has produced outstanding results in the past few years. From such successes as Leduc and Redwater on the western plains, oilmen are now moving north in the ever-widening search for oil. They are reaching new frontiers and meeting new problems presented by this vast hinterland.One of the least known but most troublesome phenomena which will be encountered is permafrost. This term relates to a thickness of soil or other superficial deposit, or even of bed-rock at variable depths beneath the surface, in which a temperature below freezing has continually existed .for a long time. This permanently frozen ground affects, in many ways, oil exploration and exploitation. Seismic records are changed, pipe lines cannot easily be ditched into the ground, formation of wax is speeded-up in tubing and pipe lines, roads are difficult to build, and foundations of buildings and even of drilling 'rigs may require entirely new methods of construction.Permafrost underlies roughly one-fifth of the entire 'land surface of the world. It covers the northerly portions of Eurasia and North America. In the area that we are here concerned with, the southern boundary of permafrost extends south of east from about latitude 59°N. on the Pacific coast across the Rocky mountains, through Great Slave and Athabasca lakes, to cape Henrietta Maria, at the junction of Hudson bay and James bay (see Figure 1). Geologists generally agree that permafrost first appeared in the Pleistocene or Ice Age as the result of abnormal ground freezing."

Jan 1, 1952

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By John Hartlen

"The 19th century was an ""age of gold"" and Nova Scotia experienced its share of early gold rushes. Gold mining activity in the province was focussed into three ""rushes"" which occurred, approximately, in the 1860s, 1890s and 1930s; a total recovery of 1.1 million oz. Au has been recorded. The purpose of this note is simply to chronicle the technical development of gold mining and processing in the province and to comment briefly on the recently renewed interest in this precious metal. The first public discovery of gold in Nova Scotia was made by a farmer in 1860 at Old Tangier or Mooseland, and this find sparked the province's first gold rush. The mining and milling methods of the 1860s were ingenious. Initially, arrastras, crude stone-hewn grinding mills, drawn by men, mules or horses, were widely used. Nova Scotia's first conventional stamp mill was installed at Mooseland by 1862; it was comprised of four wooden stamps and is believed to have been imported from Scotland. One of the largest waterwheels of the 1860s, reportedly 16 feet in diameter and 8 feet wide with a SO-horsepower rating, was used in the Renfrew Gold District to drive gold stamps. Steam power was also employed, and many of the engines were of native construction, as was the unit at Waverley's Lake Major Company, which had a piston 1 foot in diameter by 12 feet long and was connected to a 16-ftdiameter flywheel."

Jan 1, 1999