Search Documents

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By A. del Campo A.

The roast segregation process, which was patented in 1974, makes use of a set of chemical reactions that are different from the traditional sequential oxidation of iron and copper sulfides used by all modem pyrometallurgical processes to treat copper concentrates. It allows metallic copper to be obtained via sublimation of copper chloride at temperatures in the range of 700-800 OC. In addition it avoids melting the concentrate, doesn't require transferring molten materials, doesn't need flux addition and allows nearly all of the sulphur to be removed in one stage as a high-S02 gas stream. Most importantly, it allows a decrease in the use of energy to approximately 6 million BTU/ton of anodes. This represents a saving of approximately 40%, compared to the potential of the most advanced processes presently used. Such a promising process has been waiting for its first industrial application for more than 30 years. This article examines the technical difficulties that have delayed application of the roast segregation process to beneficiate copper concentrates. Special emphasis is made on material handling aspects, discussing the possibility of using a well designed mass flow silo as the main processing vessel to carry out the segregation stage. Cu2007

Jan 1, 2007

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By Chen Feng

Compared to widespread successful deployment of robotic manipulators for repetitive and hazardous tasks in related industries such as manufacturing, the construction industry has achieved relatively limited benefits from robotics and soft automation. Unlike manufacturing, where robotic solutions benefit from the structured layout of the environment (e.g., factory assembly line), construction robots face unique challenges that arise from the rugged, dynamic, and unstructured environment of the work site, as well as the uncertainty and evolving sequence of occurring on-site events. This challenges any intended construction robots to not only replicate basic human motion, but also be capable of sensing and adapting to environmental changes, and making decisions based on the evolving state of the environment. Building upon recent advancements in robotic mapping, computer vision, and object recognition, the authors propose to introduce autonomous behavior at the basic task level for on-site construction robots to address these challenges in a flexible and extensible manner. This paper reports the outcome of the first phase of this research - a structured methodology for improved design and development of basic task automations - and focuses on algorithms developed for mobile robot navigation and relative pose estimation. The algorithms are implemented on a prototype mobile robotic platform, and evaluated in several experimental scenarios.

Aug 1, 2013

By O. J. Restrepo-Baena, L. Rojas-Mendoza

Gold losses must be controlled during extracting processes, especially during cyanidation. Otherwise recovery decreases and therefore the profitability of projects too. One of the phenomena that generate such losses is known as preg-robbing which occurs when some mineral constituent adsorbs aurocyanide complex from a cyanide solution. There are some laboratory methods to identify potential preg-robbing in gold ores, highlighting the PRP method, the BGMI test, and cyanidation tests by conventional agitation without activated carbon (BRP) and with activated carbon (CIL). For this study we performed an initial characterization of a sample from Antioquia - Colombia and then we carried out the methods described above in order to identify the presence of carbonaceous matter. We obtained a percentage of preg-robbing of 78.7% by applying the BGMI test; the preg-robbing potential by the PRP method was 97.9% with an extraction of 0.77% and an inferred recovery of 36.6% if preg-robbing did not occur. Finally we obtained under the BRT test a recovery of 0%, while for CIL test an extraction of 33.6% what confirmed the presence of preg-robbers agents in the gold ore. We conducted all tests in the Institute of Minerals - CIMEX at Universidad Nacional de Colombia - Medellin.

Jan 1, 2014

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004

By T. Schmidt, H. Assadi, F. Gartner, H. Kreye

Among all spraying processes, cold spraying has attracted a special attention in recent years, both as a coating - and more recently - as a rapid manufacturing technique. The interest in this process is mainly because of the fact that the deposition of spray material takes place at moderately low temperatures, and thus, oxidation and unfavourable microstructural changes can be alleviated. In this process, a highly compressed gas, flowing through a de Laval nozzle, accelerates the particles of the spray powder to high velocities of up to 1200 m/s. Although there is no melting of particles prior to impact on the substrate, cold-sprayed deposits can be denser and more tightly bonded as compared to the equivalent deposits produced by conventional thermal spraying methods. The present contribution focuses on this unique aspect of cold spraying. Modelling of particle impact, combined with various experimental observations, is employed to illustrate that bonding of particles and hence material deposition occurs through shear instability - associated with severe plastic deformation and localized heat generation - at the interacting surfaces of particles and substrate. The results of modelling also provide an insight to the influence of material and process parameters on the critical velocity and on the microstructural properties of cold-sprayed deposits.

Jan 1, 2006

By J. R. Shouldice

"IntroductionREEFS of Silurian age are recognized in southwestern Ontario, both in outcrop and from subsurface information. This paper deals with the so-called 'pinnacle' reefs which are known only in the subsurface. For the purpose of this paper, the pinnacle reefs are arbitrarily defined as those structures having a height of over 250 feet and a length of less than two miles. This definition eliminates numerous mounds and other broader, more subdued, structures of less certain origin, found in subsurface beds.The term 'pinnacle reef' is perhaps unfortunate, but it is in common usage in Ontario and is used elsewhere for different types of reefs. A new name is justified by the unusual environment and structure of the Ontario reefs, but it is unlikely that any other term would gain acceptance. Rather than propose a new term which would be ignored or result in further confusion and misuse, the name 'pinnacle', as defined above, is used in this paper.Pinnacle reefs have been found over a fairly large part of southwestern Ontario. The known reefs of this type parallel the southeast edge of lake Huron and •follow the strike of the structure contours which circle the Michigan basin (see Figure 1). In total, twenty-five such reefs have been discovered in southwestern Ontario."

Jan 1, 1955

By Paul A. Glapa

Quality is much more than providing a product that functions properly. True quality is a way of thinking, a way of doing business, and, ultimately, a way of satisfying a customer?s long-term needs. A true commitment to quality requires a top-down management commitment, with a willingness to change what needs to be changed and to expand upon ?best practices? that are already done well. Is there a cost to creating and maintaining a quality program? Of course there is, but the cost of not having a focused program is much greater. We have come to regard quality as an investment that pays dividends to both the supplier and customer. The lack of quality costs everyone and the customer pays the ultimate penalty. With modern, highly engineered surface mining equipment the end user calculates cost in terms of lost production (revenue), not simply the cost of the part. Bucyrus International, Inc. is a company that has listened to its customers and has dedicated itself to implementing an advanced quality program. The ultimate goal being the creation of a high quality product with extended reliability for the customer. The result is reflected in Bucyrus? current product offerings and highlighted by the new 495HF electric rope shovels at Albian Sands mine.

May 1, 2003

By Yu-Min Cheng

Over the past two years, the construction industry has increasingly recognized the benefits and capabilities of building information modeling (BIM) for information integration, visualization and parametric design, reducing the duplication of work and complexity of interface integration, while significantly saving both time and cost. However, due to the variety of participants in engineering projects, the differences between data definition, data format, and data storage increase the difficulty of integrating data from diverse sources. Therefore, buildingSMART has developed a common data schema, called Industry Foundation Classes (IFC), that makes it possible to hold and exchange relevant data between different software applications, to increase the efficiency of BIM work and to ensure a consistent and high-quality output. This paper presents a novel methodology that assists in facilitating the import and export process for parametric BIM objects between heterogeneous BIM systems. This methodology is based on the IFC data schema and includes graphical and non-graphical description data. The objective is to retain the geometry, parameters, unit, texture and links of an object during exchange and sharing to ensure that data integrity is maintained. To sum up, this research addresses the issues of transferring parametric BIM objects between heterogeneous systems to increase data integrity and reduce transfer and integration times.

Aug 1, 2013

By N. M. Steven, J. M. Moore, J. L. Kuyper

Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, Iargelyensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegrnatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphic order of host rock): (1) thin (5 cm to 2 meter) quartz+plagioclase+diopside ± scapolite calc-silicate granofels with fmely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the calc-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); (2) gamet+pyroxene± vesuvianite+scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unrnineralized leucogranites; (3) metaturbidite-hosted scheelite- (and possibly wolframite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; (4) scheelite-bearing vesuvianite+quartz+garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt5 WO3 and 8 wt% CaF2•

Jan 1, 1994

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter's requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

By Robert B. Parsons

"Once all the hullabaloo about Finance Minister Wilson's April 27 budget died down (or was it an April 26 budget?), the pain of the budget papers began to sink in. Individuals and corporations will have to dig deeper and pay more taxes - and government will continue to dig deeper and spend more. The irony of the situation is that higher tax rates actually make flow-through shares more attractive as a tax-deferral investment - a bittersweet ""bravo"" for the mining industry.INTRODUCTIONFor the first time in Canadian history, a major budget address has taken two days to deliver. Of course, it's not a case of long-windedness, but rather a case of a hastily called press announcement on April 26 in response to a budget leak, followed by a formal budget speech on April 27.The general reaction of the business community to the budget was to the effect that the tax hikes are acceptable, but the government's failure to curb spending is less than acceptable. Mr. Wilson's reported response indicated that the government had never promised to cut spending, and that increased government spending would actually benefit the country. That age-old debate will doubtlessly continue for generations.In any event, three noteworthy components of the budget papers are:• Personal income tax rates increase effective July I, 1989;• A ""large corporations tax"" (in effect 'a corporate ""minimum tax"") is effective July I, 1989; and• Federal sales tax increases are effective from June 30, 1989, to be replaced by a national sales tax in 1991.A brief overview of these and other budget proposals follows."

Jan 1, 1989

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003