Search Documents

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Constrained groove pressing (CGP), as a severe plastic deformation (SPD) technique, is one of the applicable methods for sheet metal forming capable of producing ultra-fine grained materials (UFGMs). In CGP, processing and die design parameters can significantly affect the deformation response of sheet metal specimen. Having said this, in the present research the effects of die design variables and processing parameters (i.e. shear angle and friction) on the deformation behaviour of an Al-Mg-Si Alloy are studied thoroughly. Finite element analysis (FEA), was used to evaluate the effectiveness of mentioned parameters on the deformation homogeneity, strain distribution and pressing load variations. Also, mechanical properties of the deformed sample in term of micro-hardness was analyzed. It is observed that with increasing the shear angle, effective stress, strain and pressing load are enhanced. Moreover, by increasing the coefficient of friction, pressing load enhances. The color coded micro-hardness measurement showed a good agreement with the strain distribution obtained from FEA (higher hardness for the zones associated with higher shear plastic strain values).INTRODUCTIONWork hardening results in enhanced mechanical properties upon cycles of deformation (Hosford & Caddell, 2007). However, the formability of the processed products are affected by work hardening reducing the possibility of processing in subsequent deformation cycles. Therefore, many industrial processes cannot be performed on sheet metals to produce products with desired mechanical and physical properties (Valiev, Islamgaliev, & Alexandrov, 2000). Severe plastic deformation (SPD) is an effective grain refining technique which can impose large plastic strains through cold working on a metallic specimen (Bisadi, Rastgou, Payganeh, Zeynali, & Ghahremani, 2010). SPD techniques are mainly categorized into three types; sheet, bulk and tube forming. Among SPD sheet forming methods, Constrained Groove Pressing (CGP) (Shin, Park, Kim, & Park, 2002), Accumulative Roll Bonding (ARB) (Saito, Tsuji, Utsunomiya, Sakai, & Hong, 1998) and Repetitive Corrugation and Straightening (RCS) (Zhu, Lowe, Jiang, & Huang, 2001) possess potential applications in manufacturing industries."

Jan 1, 2016

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019

By Leslie B. English

"HistoricalWHILE DIGGING caves and underground passages for living quarters, primitive man must have had some means of illumination. Most likely he used pieces of wood or slim bundles of reeds or grasses as torches, perhaps steeped in animal fats to give more light. If this is so, we may accept these as the first means of underground illumination. Very little was clone to improve lighting devices for many generations, but slowly there was developed a fount holding fatty oils, with a spout in which was inserted a form of wick.Actual mining. for metals first of all, was started about 3,000 B.C. Some of the old Greek and Roman records refer to the use of torches underground, and some evidence of clay lamps has been found. Candies came into use some time during the first century A.D. When coal mining began about the 14th Century in England, candles were used for illumination because of the ease of manufacturing and handling them. Open oil-lamps came into use early in the 16th century -Agricola, in his De Re .Metallica, written about 1540. pictures a miner with such a lamp. However, the expense of these was so great that candies still continued as the general means of underground lighting.Unfortunately, as miners went deeper underground, they encountered a mysterious gas which. upon coming in contact with open lights, flamed violently, resulting in explosions and accompanying loss of life. The first reference to the results of these gas explosions appeared in 1621. No help seemed to be available. The gas was given off when the coal was mined and the miners could not see without lamps. Attempts were made to use the phosphorescent glow from partly decayed fish, fish skins, and fungus, also to bring daylight clown into the workings by means of a series of • mirrors; •but these means of illumination proved to be impracticable."

Jan 1, 1955

By Gulshan Kumar Pradhan, Yogendra Pratap Singh, Dhawanm Nikhil

"Potassium (K) is one of the essential elements for the growth of plants and thereby for humans. In fertilizers, potash demand has been steadily increasing at ~3.5% annually. Water soluble potash deposits are rare and highly localized. India is neither present on the world potash production map nor it has adequate potash rich rocks. The K-bearing minerals are recovered either by using conventional underground mining methods or though solution mining methods. India possesses a vast resource of silicate rocks such as glauconitic sandstone and Feldspar. These rocks are basically a group of alumino silicate of potassium, sodium and calcium (K2O%: 5-12, Na2O%: 3-10%, SiO2%: 52-65, Al2O3%: 15-20, Fe2O3%:, 5-7 and MgO%: 2-3.5).The K extraction from silicate rocks has received little attention probably due to the slow release, the locked structure of alumina-silicate minerals, and the unavailability of appropriate economic processes & their know-how. In fact due to this India imports all of its potash demand (about 3.5 million tons per annum) from different countries.In the present work, an attempt has been made to identify the structural and chemical alteration of desired K mineral phase in silicate rock (~K2O%: 10.5, Na2O%: 2%, SiO2%: 55, Al2O3%: 19, Fe2O3%, 5-6, MgO%: 2.5) under different conditions such as acid leaching, thermal treatment and chemical processing. Different treatments are aimed to increase K availability which is related to the modifications in mineralogical composition. The modifications in the feed sample and treated samples are studied through SEM-EDAX, XRD, EPMA and optical microscope. With the combination of treatments, it is possible to extract more than 90% K and the formation of sylvite phase (water soluble) confirms the dissolution of potash values."

Jan 1, 2016

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By Diego L. Romero, Joy P. Romero

"IntroductionMinerals may be classed broadly as ferromagnetic (magnetite for example), as paramagnetic (attracts to regions of magnetic field convergence) and as diamagnetic (attracts to regions of magnetic field divergence). High-intensity separators are not necessary to separate ferromagnetic minerals from other classes. Rather, low-intensity units that generate fields below 5000 gauss are adequate for this purpose. However, paramagnetic minerals, such as ilmenite, with high magnetic ""attractability"" require fields of up to 10 000 gauss; those with low attractability may require even higher fields. Table 1 shows approximate ranges of field intensities necessary to separate ferromagnetic and paramagnetic minerals from minerals of lower attractability, along with the force with which they are attracted relative to iron in a standardized magnetic field.Uniform magnetic fields, not useful for separators, are generated between flat parallel surfaces; non-uniform fields, useful for separators, arise when at least one of the surfaces is of irregular shape. The diagrams below show how magnetic lines of force align relative to north and south poles.If a particle is placed in a uniform field, it feels no displacing force unless the particle distorts the applied field assymmetrically. This is not the case in non-uniform fields which are required for magnetic separators.Magnetic fields can be generated by permanent magnets (low intensity), by electromagnets (medium and high intensity) and even by superconducting coils (100 000 gauss fields and higher), although the latter are not as yet useful in production environments .The magnetic force of attraction per unit of mass, that acts on a paramagnetic mineral such as hematite, increases in proportion to the strength of the field . Unfortunately, the highest fields attainable with electromagnets is of the order of 20 000 gauss. Fortunately, the gradient of the fie ld (that is, the degree of convergence of magnetic lines of force) is important, because the attractive force per unit mass is proportional to it also . This can be stated:"

Jan 1, 1989

By Clemens Kuhnert

"Nickelhütte Aue GmbH is specialized in the recycling of waste materials containing non-ferrous metals. We treat nickel, copper, cobalt, vanadium, molybdenum and precious metal containing materials like spent catalysts, ashes, dusts, grindings, liquids, slurries and sludge's as long as they contain one or a combination of the above mentioned metals. In our pyrometallurgical works we produce non-ferrous metal concentrates suitable for further treatment in our hydrometallurgical plant where we refine Ni-, Cu-, Co- and V-chemicals. Our production is based on synergy effects due to the combination of pyro- and hydro-metallurgy. As an example we can mention our heat recovery system and internal recycling of by-products. Furthermore, the use of alternative fuels instead of fossil fuels contributes to the economic and environ-mentally friendly treatment system.INTRODUCTION Nickelhütte Aue GmbH (NHA) can look back on nearly 400 years of tradition as a pyrometallurgical works and recycling company. The existence since its foundation in 1635 as a blue dye works shows responsible and successful action in the past. Therefore, we see highest customer service, minimization of interferences with nature by closing material cycles and maximized health and occupational safety protection by avoiding injuries and diseases, still as our future duties. These duties are evaluated and monitored by an integrated management system that meets the standards of DIN EN ISO 9001, 14001, 50001 and BS OHSAS 18001. We commit ourselves to the observance of all juridical and customized demands. The management and the department managers perceive their model function. We require responsible action from all employees. To protect the continuity of our enterprise, we will also perform in future continuous improvement of products and their quality, as well as steady progress in the areas of environment protection, health protection and industrial safety. Equally the effectiveness and propriety of the management system is checked and developed regularly. In order to obtain the objectives resulting from this policy, our company determines activities and measures by involving all employees."

Jan 1, 2017

By L. Klatzel-Mudry, D. J. Nikols, J. D. Hughes

"The Geological Survey of Canada Paper 88-21, A Standardized Coal Resource/Reserve Reporting System for Canada, is referenced by National Instrument 43-101 for the preparation of resource and reserve estimates on coal deposits. However, for all disclosure of mineral resources or mineral reserves for coal, issuers are required by NI 43-101 to use the equivalent mineral resource or mineral reserve categories set out in the CIM Definition Standards and not the categories set out in Paper 88-21. “Because the framework is based on Canadian deposits and their tectonic regimes, the Canadian Securities Administrators believe it is not reasonable to apply Paper 88-21 to foreign coal properties. The “Resource Links” at the end of this volume provide website links to guidance documents for preparing coal resource and reserve estimates in Australia, South Africa, and the USA.”This report discusses definitions, concepts and parameters used to determine coal resource and reserve quantities, and provides a framework to facilitate consistent categorization of coal quantities found within various depositional and tectonic regimes in Canada.Coal deposits, or portions thereof, are first categorized in terms of their geological complexity <Geology Type), and probable recovery method (Deposit Type). Methods for determining quantification parameters including seam thickness, areal extent and bulk density are outlined for each geology/deposit category. Within each geology/deposit category, coal resources are further divided, based on their assurance of existence, into measured, indicated, inferred and speculative subdivisions and, according to their feasibility of exploitation, into immediate and future interest subdivisions. Coal reserves within each geology/deposit category are subdivided according to whether they are within or outside active mining areas, and may be reported on in place, recoverable and saleable bases.A wide cross-section of the coal industry in Canada contributed to the development of this reporting system. To ensure that the parameters and concepts expressed in the system continue to reflect technological and economic realities in the future, the Coal Association of Canada has established a committee to facilitate periodic reviews."

Jan 1, 2003

By J. Jara

Oxygen, ozone and air were evaluated in the oxidation of ferrous iron in the presence of hydrochloric acid ranging from 0.1 to 4 M HC1. Stoichiometric coefficients were determined through mass balances of gases and ferrous titration. The molar ratio ferrous to ozone increases from two at 0.1 M HC1 concentration to six at 4 M HC1. For oxygen the same ratio is constant and equal to 2 and it is in agreement with other works. The stoichiometric coefficient of hydrogen ion was not defined due to the effect of hydrolysis of ferrous and in particular ferric ion on measuring acid concentration by titration with sodium hydroxide. Agitation, gas flow and pressure contribute in the utilization of gas. A technique to compare the gas efficiency at several conditions is discussed and it is based on the relationship between oxygen and ferric during time. There is a strong compromise between gas efficiency and ferrous conversion. Oxygen efficiency decreased with time due to ferrous depletion. The gas efficiency ranged from 3 % (low level of agitation) producing 25 g Fe(III)/h to 12 % at 1000 rpm with 60 g Fe(III)/h converted. At 405 kPa absolute the oxygen efficiency was in the range of 80 % producing 300 g Fe(III)/h. The replacement of chlorine with oxygen to enrich molybdenite concentrates by reducing copper to less than 0.2 % was evaluated. Oxygen can be employed in batch or continuous operation and it can treat molybdenite concentrates with high variation of copper content. The dissolution rate is mainly controlled by oxygen addition in which utilization of oxygen plays an important role. Improvement on safety and environmental conditions is feasible by using oxygen instead of chlorine gas. The economics indicate good opportunities to implement oxygen without significant modifications to the actual circuit and enough benefit when oxygen is well used.

Jan 1, 2007

By M. P. Amsden

"Ecstall Mining is a wholly-owned subsidiary of Texas Gulf Sulphur at Timmins, Ontario. The mill tonnage is 10,000 tons per day of two different ores, a copper zinc ore and a silver lead zinc ore, producing about 2400 tons of concentrates per day. These are as a copper concentrate, a high silver zinc concentrate, a low silver zinc concentrate and a silver-lead concentrate. For flotation recovery a very fine grind is required, about 80% minus 325 mesh and the concentrates produced are 40% minus 10 microns.The thickened concentrates are pumped to the filter floor for filtering and drying. The filtering and drying section is separated from the flotation section by a wall and is controlled from a dryer control room by one operator.Two operating panels are located in this control room. One contains stop-start controls for the thickeners, filter motors and vacuum pump motors, and stop-start controls for dryer feed conveyors and dryer product conveyors to concentrate load-out bins, as well as ammeters for conveyor drive motors. Dryer throughput is regulated by Merrick Type L weightometers located on the dryer discharge conveyors and recorded on tons per hour strip charts.The second panel contains the temperature strip charts, furnace drive ammeters, scrubber and exhaust gas controls, burner controls and panel alarms for the four dryers.Filtered concentrates are dried in Nichols-Herreshoff, multiple hearth, dryers consisting of nine hearths (zinc) and seven hearths (copper and lead). There are two dryers for handling zinc concentrates and one each for copper and lead concentrates. The dryers are heated by burning natural gas. Each zinc dryer handles 1,000 t.p.d. and the copper and lead dryers 750 t.p.d. each.Multiple hearth dryers are unusual in the base metal mining industry and the reasons for selecting them in preference to rotary dryers are as follows:1) The concentrates could only be filtered to 15 to 17 percent moisture. These sloppy filter cakes would be extremely difficult to handle in rotary dryers."

Jan 1, 1972

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019

By P. J. Poirier, J. A. Meech, H. Raabe

"An Expert System has been implemented to assist operators in applying knowledge about froth conditions in the control of the flotation circuit at Highland Valley Copper. For some time, the personnel at Highland Valley Copper have recognized that froth type is a useful indicator of good operating conditions. However, the operating strategy based on froth type recognition is an ad-hoc skill in which different operators use a variety of terms, features and procedures to identify and solve problems. The first phase of this project developed an on-line consultative system to advise and tutor so that the diffuse expertise could be rationalized and consolidated into a standardized format.The second phase has brought this knowledge into a real-time environment to advise the operators on the floor in identifying froth types and troubleshooting corrective action. This paper describes the steps taken to acquire the knowledge, to design the required system features and to implement the real-time version of this system.INTRODUCTIONThe use of expert systems in the mineral industry has been gaining popularity in recent years. Minnova Inc, Les Mines Selbaie, Wabush Mines, Potash Corporation of Saskatchewan are just a few examples of Canadian mining companies that use expert systems to monitor or control their plants. Applications in the field of flotation include Brenda Mines (Edwards, 1992), Mt Isa Mines Ltd (Lacouture et al, 1991), Outokumpu (Karhu, 1989) and Kidd Creek (Burrows et al., 1989).Expert systems are defined as ""computer systems that apply reasoning methodologies on knowledge in a specific domain in order to render advice or recommendations much like a human expert"" (Turban, 1988). The main areas of application are diagnosis, training, process monitoring and control, and design. There are basically two main types of expert systems: Consultative systems, which are off-line applications in diagnosis and design, and on-line realtime systems, used for supervisory process control and real-time advising."

Jan 1, 1993

By Bern Klein, A. Tugba Cebeci, Libin Tong

"Sensor based sorting faces two main challenges related to limited capacity/throughput and the ability of sensors to accurately discriminate based on estimated grades. This paper is aimed at improving sensor discrimination. Sensors have the ability to measure more than a single response. X-ray fluorescence (XRF) can detect and provide concentration information about a range of elements. Similarly, electromagnetic sensors (EMs) can generate magnetic susceptibility and conductivity responses over a range of frequency levels. The sensors thereby provide a response signature rather than a simply a single response that is a proxy for a metal grade. Furthermore, integrating sensor responses can improve the discrimination of metal bearing rock from waste. A study was conducted on a gold ore to assess sortability using XRF and EM sensors. A multi-variable regression approach was used to develop models that included a range of responses. Correlations improved significantly when compared to single response correlations. The approach showed that both positive and negative correlations contributed to the improved correlations. Stepwise regression simplified the models and showed that 2nd order interaction effects can be important. The approach also showed that combining different responses can improve discrimination accuracy. An important outcome of the study was that an ore that had been consider not to be sortable was determined to be sortable through the application of an approach that used the sensor responses in a more intelligent manner.INTRODUCTIONMining is aimed at recovering valuable minerals from their host rocks. Many methods are used to recover valuable minerals, and finding efficient and cost-effective ways is the key in research and production. . Ore sorting technology is fitting this definition. It not only discards waste rocks away from the concentrator but also recovers metal bearing ore particles that could be lost to the waste dump. The benefits of ore sorting include increased energy efficiency and reduced water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013)."

Jan 1, 2016

By William D. Gallant, Thomas M. Barczak, Carol Tasillo

"This paper describes the results of full-scale testing of several multi-layered wood crib configurations that were tested in the Bureau of Mines mine roof simulator in cooperation with the Cape Breton Coal Research Laboratory and Cape Breton Development Corporation of Sydney, Nova Scotia. Nine different crib configurations currently being used as wood packwall supports for advancing longwall applications in Canada were evaluated. Configuration parameters understudy included the aspect ratio (height-to-width relationship) and percentage of solid material used in the crib construction. Test results and generalized wood crib behaviour are discussed in detail. Recommendations are made concerning crib constructions to maximize strength and stability. A cost benefit analysis of multi-layered wood crib configurations is made. A comparison of laboratory results and underground observations of several wood packwall supports in the Sydney coalfield suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load bearing capability are described.IntroductionA cooperative effort was undertaken by the U.S. Bureau of Mines with the Cape Breton Development Corporation (CBDC) and the Cape Breton Coal Research Laboratory (CBCRL) to evaluate the behaviour of gateside packing materials used in advancing longwall mining applications in the Sydney coalfield. As part of this effort, full-scale tests were conducted on wood packwall supports in the Bureau&apos;s 3-million pound (13.3 MN) active load frame.Nine different pack configurations were evaluated as part of this study. The wood packwall supports were multi-layered crib constructions from 6 in. (0.15 m) by 6 in. (0.15 m) cross section timbers using timber s 30 in. (0.75 m) and 60 in. (1.5 m) in length . The percentage of solid material in the crib constructions varied as illustrated in Figures 1 and 2. A summary of crib constructions is provided in Table 1."

Jan 1, 1991

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies&apos; bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By W. B. Morrey

"In recent years, the major effort in detonator development has been concentrated on ""non-electric"" systems. Existing types all involve some form of explosive reaction to transfer ignition energy from outside the borehole to the pyrotechnic delay element contained within the detonator. These may be based on low-energy detonating cords having grained or plasticized explosive cores, shock tube energy transmission principals and explosive gas ignition systems. Each has properties of internal and external effects not present in electric conductors.The MAGNADET System introduces transformer coupling into electric blasting circuits. Safety features with respect to current leakage, stray currents of AC or DC source, electrostatic energy and radio-frequency radiation are comparable to ""non-electric"" systems, with advantages in simplicity, speed of hook-up and range of application.The transformer device used is a small ferrite ring or toroid which is an integral part of each specialized detonator. The detonator legwires form the secondary side of the transformer winding. The primary side is a single wire loop common to all units within the circuit. Power is supplied from a frequency-tuned portable exploder with unique circuit-sensing features.The MAGNADET System is expected to have particular application to shaft sinking, raising and tunnelling where the protective features as well as speed and efficiency are critical factors. Applications of the &apos;MAGNA&apos; booster in quarries, open pits and longhole deck charges offer control over vibration problems and elimination of surface noise.IntroductionFor many years, electric detonators and electric blasting systems dominated surface and underground applications where controlled delay times were required. Control over the instant of detonation by blasting machines or power-line switches is the major safety feature.Electrical energy exists in many forms. It may originate from many sources. Electrical energy can be difficult to contain. It may enter or escape through a variety of conductive paths. It may fluctuate, concentrate or dissipate to pose a most elusive potential hazard."

Jan 1, 1982

By A. C. Moerman, C. W. Pelley, K. R. Notley

"The software package described in this paper facilitates the handling of diamond drilling information in the creation and maintenance of a geological information database. Once entered, the drilling information is stored in a direct access file for rapid retrieval. The drill data are sorted into vertical cross sections and interpretation is performed using on-screen menus to define areas of common rock type and outline the mineralized zones. Intersections of individual zones can then be examined and outlined in the longitudinal dimension at a graphics terminal.With the aid of surface-fitting routines, the digitized information can be used to generate three-dimensional models of each zone. From these models intermediate cross sections and level plans can be obtained. Several interpretations are possible and plotter drawings can be obtained. An output file for use by ore reserve estimation software can also be created.Future work will tie this software to geostatistics and mine planning programs and will be aimed at converting mainframe software to run on microcomputers. IntroductionComputer applications in underground mine planning and geology are not new. Operations such as Sherritt Gordono and Kidd Creek have been using software developed about a decade ago for handling geological information and designing stoping blocks. However, general use of such systems has been limited mainly due to the cost of hardware which was affordable only to large corporations. Software to perform the work was usually developed on site and was largely unavailable for use by others, being site-specific, or too expensive for other organizations to purchase.The increasing power of microcomputers and mini-computers, and their relatively low cost compared to the mainframe computers which were previously used, has led to the increased use of computers at mining operations of all sizes. Sources of software for use in geological interpretation and mine planning have increased in number with the proliferation of the use of microcomputers."

Jan 1, 1988

By J. S. Fox

"Besshi-type Cu-Zn (-Ag-A u ± Co) deposits are tabular, stratiform volcanogenic sulphide bodies which are usually associated with mafic volcanic rocks of oceanic or intra-plate geochemistry, but which can also be found locally with ultramafic volcanics or subvolcanic mafic intrusions. A thick sequence of continentally-derived clastic sediment usually encloses both the mafic volcanics and the ore. Besshi-type deposits form subaqueously, in epicratonic rifting environments, more-or-less proximally, and as a result of hydrothermal convection in their subjacent mafic volcanic - clastic sedimentary piles. They belong to a rift -related metallogenic spectrum that includes sediment-hosted and Cyprus-type base metal deposits, and may diller genetically from these mainly with respect to rate and degree of crustal extension. Modern analogues to these deposits are f ound in the submarine volcanogenic sinters of the Gulf of California rift system.The associated lithologies and tectonic selling of Besshi-type deposits clearly distinguish them from Kuroko-type ores. This difference also seems to be reflected in their lead isotopic character. For example, leads from Besshi-type deposits in the Sanbagawa belt of Japan and from the Blue Ridge belt of southeastern U.S.A. lie on extended anomalous lead lines and have lowslopes in 207Pb/204 Pb - 206Pb/ 204 Pbspace (Sato and Sasaki, 1980; Leriuray, 1982), wheras those from most Kurokotype mining districts exhibit only narrow isotopic ranges and lie near or on the orogene growth curve (e.g. , Franklin et a I., 1981). More over, where Besshi- and Kuroko-type deposits are found in the same orogene, the former often occur earlier in the tectonic cycle than the tatter (e.g., Japan, the Norwegian Caledonides, the southern Appalachians and south-central Finland).Besshi-type deposits are not confined to any particular part of the world, or to any geological epoch. Moreover, in many mineralized belts, Besshi-type deposits are the predominant volcanogenic ore type. On a world-wide scale, deposits of this type therefore constitute an important base metal resource."

Jan 1, 1984