Search Documents

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

By B. Van den Bogaert, K. Binnemans, T. Van Gerven

Europium is one of the most critical rare-earth elements due to the limited supply of this element combined with a high demand for red lamp phosphors. Therefore, the recycling of europium from end-oflife lamp phosphors has become increasingly important. Photochemical reduction of europium(III) to europium(II) and subsequent removal from rare-earth mixtures by precipitation as EuSO4 is a very selective and efficient method to recover europium from binary europium/yttrium solutions. It is shown that full separation of europium and yttrium is feasible from laboratory prepared non-equimolar Eu/Y mixtures up to a ratio of 1/20, which reflect the composition of red lamp phosphors. Optimal conditions were determined at pH 4 with isopropanol as a radical scavenger, which is a less harmful and toxic compound than the commonly used formic acid scavenger. Europium removal efficiencies of more than 95% were achieved, with a purity of 98.5% of the EuSO4 precipitate. The irradiance of the used light source, expressed in mW/cm2, has a large impact on the illumination time needed to remove europium from the solution. It is observed that higher irradiance results in a shorter induction time, i.e. a period during which virtually no europium is removed, and a faster removal rate once the induction time has passed. The photochemical separation technique was applied to recover europium from leached industrial red lamp phosphor (YOX) powder, with a Eu/Y ratio of 1/30. Europium recovery of 50% was reached with a purity of 96%, proving the feasibility of this method for the recycling of europium from end-of-life lamp phosphors.

Jan 1, 2016

By John Drobe, Robert M. Cann

"Abstract - The Minas de Oro Cu-Au skarn and replacement deposits are located in the highlands of central Honduras, 90 km north-northwest of the capital of Tegucigalpa.The deposits formed in Cretaceous volcano-sedimentary rocks following the emplacement of an early Paleocene granodiorite to dacite intrusive complex. Three types of skarn (Type IA, IB, and IC) and a low-temperature replacement mineralization (Type II) are recognized. Type IA skarn consists of massive brown-green andradite and lesser magnetite and pyroxene. Type IB skarn has magnetite + hematite as the main constituent and garnet <50%. Type IC skarn comprises >50% pyrrhotite + chalcopyrite with interstitial garnet or pyroxene. Au and Cu occur in potentially economic concentrations in all skarn types while other metals such as Ag, Pb, Zn, and Mo are locally present in significant quantities. The highly variable distribution and nature of the skarn deposits is controlled by: (1) intrusive activity, (2) composition of host rocks, (3) faulting and fracturing, and (4) attitude of host carbonates.Type II Au-Cu-As mineralization occurs in calcareous sandstone and conglomerate 2 km distal from skarns and comprises clots of Cu sulfides hosted within a zone of brecciation and quartz flooding. Garnet and/or magnetite skarn is not present and the mineralizing event appears to have been a low-temperature replacement type.The similarity of coeval Au-Cu-Fe skarns in central Guerrero, southern Mexico to Minas de Oro skarns, and the similar local stratigraphy is consistent with the generally accepted theory that the Chortis block originated from southern Mexico and during the Tertiary moved southeast to its present position."

Jan 1, 2000

By C. Bourgoin

"The factors constraining productivity in the mining of narrow vein ore deposits are numerous and often interdependent. This paper concerns mining techniques capable of reducing some of these constraints in the case of vein deposits whose dip is less than 45 degrees. Modifications of conventional mining methods as well as suggested new developments are presented, as are matters pertaining to the mechanization of operations as a mean of increasing both productivity and work safety. IntroductionThe mining of vein deposits, whose width (thickness) is generally less than 2 metres and whose dip is often variable, calls for the use of varying stoping procedures as well as appropriate infrastructure and equipment. In the case of intermediate dips (15 degrees to 45 degrees), it is generally conceded that the degree of mechanization is limited and that ore removal via gravity is impossible. This paper proposes certain innovations in matters of equipment use and stoping methods, together with certain technical data pertaining to the application of these new procedures Stoping MethodsTo mine vein deposits, one must choose a method that can adapt to irregular ore limits and allow, as well, for good ore recovery with as little dilution as possible. In addition, it is important to minimize development work in waste rock. In principle, one selects a method that is both safe and profitable; this method will be defined mainly by the nature of the vein deposit and its dip, by the competency of the rock formations and by certain technical considerations. Moreover, the stoping procedure in a given deposit may well change with time as a function of new layouts or new equipment."

Jan 1, 1994

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By J. C. Kurnia

Methane is recognized as one of the prime causes of underground mine disasters around the globe. A cost-effective mine ventilation system and methane control is required to ensure a safe and productive environment in an underground mine whilst keeping energy usage and operating cost at minimum. Typically methane enters a mine environment or tunnel from localized distributed sources at high initial concentration. Hence, an understanding of its dispersion from discrete sources is important to design a methane management system via effective ventilation. This study employs computational fluid dynamics to model methane dispersion in an underground tunnel which has a number of discrete sources of methane and effective ways to dilute and or disperse it. Air flow distribution within the tunnel as well as methane dispersion is simulated by solving the governing transport equations subject to appropriate boundary conditions. First, the effectiveness of ventilation duct placement is examined. Several possibilities are explored and investigated. It is found that the common configuration utilized in underground mine performs best as compared to other configurations in maintaining the concentration of methane below permissible levels. Next, a novel intermittent airflow ventilation system is proposed and evaluated via simulation with the goal of reducing the energy cost whilst maintaining methane level in the mining face below the allowable level. Parametric studies are conducted to investigate effects of various factors influencing the effectiveness and performance of this novel intermittent ventilation system. This study will provide some new ideas for designing an efficient and effective underground mine ventilation system by lowering the net average amount of air that needs to be circulated in the tunnel for a safe operation. KEYWORDS

Aug 1, 2013

By D. E. Barnett

"Paramount to sound aggregate resource management is an awareness of what resources exist. For the past six years, New Brunswick has been conducting granular aggregate resource inventories in and around urban centres as a means of documenting, both qualitatively and quantitatively, these resources.These aggregate studies require extensive ground truthing due to the often small nature of the surficial feature s as well as extensive foliage. Approximately 35% of the province&apos;s land mass has been mapped at a 1:50,000 scale as part of this on-going program. Reports are published annually and include data on size analysis, lithology soundness, abrasion and absorption.Aggregate deposits in New Brunswick frequently reflect the local bedrock lithology and, whereas much of New Brunswick is underlain by soft, friable sandstone of Pennsylvanian age, it is necessary to transport aggregate for higher-specification use considerable distances. Alternatively, the construction industry must turn to crushed stone as a source of asphaltic or concrete aggregate.Over 40% of New Brunswick&apos;s land mass is owned by the Crown, and aggregate resources are managed under the Quarriable Substances Act. Under this legislation, permit applications are reviewed by a Land Management Advisory Committee which consists of representatives from the various government departments involved.IntroductionSurficial materials either directly or indirectly form the basis of much of our economic activity, whether it is the field of agriculture, forestry, manufacturing, construction or other. Although sand and gravel have been produced and used since the day s of early settlement, the economic significance attached to such materials has only recently been recognized by both government and the general public."

Jan 1, 1982

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of &apos;bumps&apos; and &apos;outbursts&apos; have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By N. W. Hendry

ABSTRACT Exploration by geophysical methods and diamond drilling of an occurrence of chrysotile asbestos, located ten miles east of Matheson, Ontario, was commenced on March 25th, 1949, by the Canadian Johns-Manville Company, Limited. The asbestos is associated with a narrow sill-like body of basic and ultrabasic rocks which strikes northwesterly across portions of Munro and Beatty townships. To date, asbestos zones of commercial interest, many hundreds of feet in length, width, and depth, have been outlined by diamond drilling along a 2-mile length of serpentine. The fractures occupied by the asbestos veins are closely associated with the regional faulting in the area. The mining of the first occurrence, or A orebody, will be by open-pit methods. Milling will commence at a rate of 50 tons an hour. INTRODUCTION OCCURRENCES of chrysotile asbestos in Munro township have been known at least since 1914 and references to them appear in reports published by the Ontario Department of Mines in 1915 (1) and 1919 (2). J. G. Ross (3) in his excellent publication on Chrysotile Asbestos in Canada, mentions an occurrence in Munro township. The area was first mapped in detail by J. Satterly, of the Ontario Department of Mines, in 1944, and brief mention is made of chrysotile asbestos in Satterly&apos;s preliminary report (4), which was published the following year.

Jan 1, 1951

By M. O. Makwarela, M. W. Erwee, K. Bisaka

"Energy efficiency in mining and minerals processing forms part of Mintek’s long-term research strategy which includes a specific programme designed at overcoming the challenges faced by the South African pyrometallurgy industry.The electric smelting industry is currently severely constrained by the global economic downturn as well as by the availability and increasing cost of electricity. Efficient utilisation of electricity through energy recovery systems and improved smelting process flowsheets can significantly contribute towards creating sustainable operations.Apart from efficient engineering design and solid process control, smelting of either cold or hot pre-reduced ores has been shown to decrease furnace electricity consumption by more than 40%. Various methods of solid-state reduction tests have been carried out at Mintek in order to select the most appropriate process option in the context of the South African industry. This paper summarises a subset of the results obtained, specifically on pre-reduction tests done on South African chromite and manganese ore pellets.In this set of tests, it was found that the use of an organic binder, together with B2O3 as flux, promotes manganese ore pre-reduction, but retards the pre-reduction of chromite. By pre-reducing the manganese ore feed, significant cost savings can be achieved in subsequent smelting processes and there is potential to minimise manganese losses as a result of fuming, due to possible lower operating temperatures."

Jan 1, 2016

By Sanat Talmaki

Construction and mining worksites pose unique challenges to workers and equipment operators due to their dynamic and unstructured nature. Narrow haul roads, crowded work spaces and presence of workers and equipment in close proximity, combined with large blind spots and overall poor visibility afforded to operators lead to collisions and run-over-type accidents between equipment, workers, and other entities that may be present on the jobsite. Operations that involve machine-infrastructure interaction, particularly in the case of concealed infrastructure such as excavation and drilling lead to unintended strikes between the equipment?s end-effect or and the infrastructure. Such accident-prone scenarios can be avoided by providing operators with real-time feedback and warnings using 3D visualization and proximity monitoring of the entities present in the equipment?s vicinity. Thus the jobsite in the real world is abstracted and represented in a 3D virtual world. However, this requires the ability to create a seamless link between real-world sensors present on the equipment and/or the jobsite and the virtual environment. This paper describes a non-restrictive acquisition allocation framework that allows position and orientation sensor streams from construction and mining job sites to be used for updating 3D virtual scenes in real-time for providing vital collision avoidance warnings to equipment operators.

Aug 1, 2013

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By R. Bainbridge

"IntroductionTHE LEAD SMELTING Department of The Consolidated Mining •and Smelting Company of Canada, Limited (Cominco), at Trail, B.C. treats materials from numerous sources for the recovery of lead, •and, of secondary importance, for the .recovery of sulphur as S02• The Department's sintering section has a .capacity of 1,500 tons daily. This section is being replaced by •a new charge-•handling and sintering plant with a daily capacity of 2,000 tons of finished sinter. Materials handled in the sintering section comprise concentrates, ores, and fluxes from Company mines and from 'custom' (independent) producers, together with intermediate products from various plants of Cominco'•s Metallurgical Division, all of which must be treated to, make up a chemically balanced charge of a predetermined lead content for the sintering plant.As received, 80 •per .cent of these materials are finer than 200 mesh, and one-quarter of the tonnage (dry basis) is a slurry .at 30 to 40 per cent moisture. This slurry, a -residue from the electrolytic zinc operation, was, for many years, partially dried before being mixed with other dry materials to make up the sinterplant charge.Some experimental work carried out in 1937 indicated that the metallurgy of the sintering operation could be improved by adopting a technique of 'wet-mixing' followed by controlled drying and nodulizing."

Jan 1, 1953

By P. Mpofu

In this work, the modification of interfacial chemistry of colloidally stable kaolinite clay dispersion has been carried out to improve its flocculation performance and dewatering behaviour. Synergistic action between dispersion pH, hydrolyzable metal ion and high molecular weight polymeric flocculant structure type (anionic polyacrylamide-acrylate copolymer (PAM) and non-ionic polyethylene oxide (PEO)) was found to play a pivotal role in inter-particle bridging, the enhancement of the settling rate and extent of consolidation of the pulps. Flocculation with PEO led to higher settlings rates in acidic than alkaline pH, whilst for PAM, the maximum dewatering rate was achieved in the neutral pH range 6 - 7.5. Upon shear, the PEO flocculated pulps showed dramatic improvement in consolidation to 40 wt%, the extent of which was greater at lower than high pH values. For PAM-based pulps were however, not shear-responsive, lower sediment solid contents of 15 - 23 wt% was observed between pH 3 and 11. Hydrolysable metal ions, Mn(II) and Ca(II), used respectively at pH 7.5 and 10.5 in conjunction with PAM and PEO, significantly enhanced the settling rates and consolidation of the pulps. The findings exemplify the strong links existing between pH-mediated particle surface chemistry. polymer structure-conformation, inter-particle bridging and dewaterability of kaolinite dispersions.

Jan 1, 2004

By A. R. Barnes, N. Stubina

Increasingly, gold producers are forced to treat ever more refractory ores. While ores containing pyrite, arsenopyrite and carbonaceous material have been subjected to complete pressure oxidation (PDX) as the standard process for such ores, recent improvements in fluid bed roasting technologies have led to a resurgence of interest in roasting as a viable alternative. The lower capital and operating costs of roaster installations add further impetus to this trend. The Extractive Metallurgy Group at Xstrata Process Support operates four fluid bed reactors of various sizes which have been utilised on a large number of projects to treat highly refractory ores. Preliminary mineralogical modelling of both the physical and chemical aspects of the roasting process and subsequent testing under carefully controlled conditions has allowed clients to obtain gold recoveries approaching or matching those achievable by PDX. The flexibility of the units to operate in various modes- " bubbling bed", circulating bed, two stage, sub-stoichiometric and combinations of these, and the range of sample sizes accommodated, from a few kilograms to a few tons, has enabled XPS to accommodate clients with a wide variety of gold bearing refractory ores from all over the world. This paper outlines the key challenges of fluid bed roasting of refractory gold ores, describes the methodology used to design the testwork program and provides some results from select test campaigns.

Jan 1, 2011