Search Documents

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By B. Fang

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment, The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate, The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

"The success or failure of coal mining operations in Western Canada may hinge on the ability to extract thick coal under a variety of geological and mining circumstances and conditions. The paper presents, in who-where, what- how pattern, the current status of undergrounud mining of thick coal seams based on a review of foreign technical literature. The underground production of coal from what are considered to be thick seams is over 300 million tons per year. Methods of mining have evolved, through years of trials and tribulations, capable of meeting the requirements of a modern mine: high bulk outputs from a limited number of mining faces by concentrating in the horizontal (mechanization) and in the vertical (increased working lift)."

Jan 1, 1972

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By Javier Linares García

At then end of this year will be 10 years of producing concentrate for Antamina. This is a summary of what occurred over the last decade to increase production and tonnage above the design tonnage of 70,000 tonnes per day, up to an average of 100,018 tonnes per day in 2010, an increase in production of 42.9%. Equipment currently in use is the originally installed equipment, signifying a meaningful increase in capacity without capital. In this paper, the different phases of improvements and the realization of their impacts in chronological order will be outlined. Figure 1 below shows the average daily tonnage processed each year (tonnage throughput each year/calendar days), as well as the percentage increase over the tonnage of design.

Jan 1, 2012

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

By S. Radacina Rusu

The satellite-based global positioning system (GPS) has significantly changed the way site operations are carried out in surface mining. The GPS has impacted safety, productivity, fleet efficiency, and maintenance practices. However, no comparable global localization system exists for underground mines. This paper discusses recent work in the application of ideas from the mobile robotics research community to the problem of real-time vehicle positioning in underground drift networks. Related previous work recently focused on the creation of globally consistent 2D maps of underground environments that possess sufficient detail to be used for underground localization. Our current work entails the development of a GPS-like system for mobile mining equipment, with results given from both laboratory and field experiments.

May 1, 2011

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By P. G. Killeen

Proper calibration of portable gammaray spectrometers and spectrometric logging equipment is essential if they are to be used for accurate quantitative determinations of radioelement concentrations. In the case of both types of equipment, it is necessary to determine the system calibration constants (stripping factors and sensitivities). In the case of borehole logging equipment, it is further necessary to determine the system response characteristics if the data are to be computer processed to improve the accuracy and resolution of the logs. Facilities are now available near Ottawa for the complete calibration of portable gamma-ray spectrometers and spectrometric logging equipment, in addition to already existing facilities for calibrating airborne gamma-ray spectrometers. Limited additional facilities are also available or planned in several other areas of Canada.

Jan 1, 1978

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By T. Sakai

Present authors have succeeded in single pass large draught rolling of AZ31 and ZK60A magnesium alloy sheets below 200 °C without heating rolls by raising rolling speed above 1000 m/min. Heavy reduction larger than 60% can be applied by single pass high speed rolling even at room temperature. The rolled sheets showed fine recrystallized microstructure by dynamic recrystallization. The improvement of workability at lower rolling temperature is due to temperature rise by plastic working. In high speed rolling, almost all of the work done by plastic deformation is converted into the heat that raises the temperature of the sheet during rolling because the heat did not flow out of the sheet by conduction and radiation within very short time.

Jan 1, 2006

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By H. Assadi, S. Reutzel, D. M. Herlach

Intermetallics exhibit unique solidification behaviour due to their chemical longrange order. This includes, for instance, generally slow solidification kinetics, and in some cases, an anomalous partitioning behaviour. In the present work the electromagnetic levitation technique - complemented by theoretical modelling - is used to explore various aspects of this behaviour, as observed in solidification of B2 phase in undercooled melts of the Ni-Al system. Moreover, a phase-field model is developed and used to illustrate the effect of chemical order on the solidification kinetics of a B2 phase in a model system. The phase-field model provides an additional basis for the simulation of solidification microstructures in intermetallic forming systems. Both experimental studies and theoretical work signify the role of chemical order in solidification of intermetallics.

Jan 1, 2006

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By C. Jewell, G. H. Rupay

"67 - 2:15-3:00Regeneration of Hydrochloric Acid from Waste Pickle Liquor Using a Fluidized Bed Reactor System. G. H. RUPAY and C. JEWELL, Dominion Foundries and Steel Ltd., Hamilton, Ont.The disposal of acidic waste liquors from pickling processes has always been a problem for the steel industry. With increased awareness toward environmental control and the problems acidic wastes create, processes utilizing recovery and regeneration of the waste acids are becoming more popular. This paper describes the Keramchemie/Lurgi process for regenerating hydrochloric acid from waste pickle liquor using a fluidized bed reactor system. The process parameters are outlined, together with a brief description of the equipment. This is followed by a discussion of the operating problems and concludes with economic data."

Jan 1, 2000

By Will Callupe Arzapalo

The success of the minimization of blast induced-damage at Barrick?s Pierina Mine in Peru is the result of an effective working relationship between Mine Operations and the Geotechnical Services Department. A detailed design criteria manual is used to match the blast plan to the site?s varying rock types and slope designs. The Geotechnical Services Department has further developed a comprehensive pre- and post-blast checklist that is critical to the drilling and blasting process as it pertains to wall stability. Wall control blasts are evaluated with quality assurance field checks, vibration monitoring and frequency control, video assisted performance quantification and post excavation face profiling. These detailed observations are compiled and summarized in a blast performance evaluation that is considered to be an ?Industry Best Practice?. The information and detail provided by each performance summary allows accurate blast analysis and effective design refinement.

May 1, 2006

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By Technische Universität Braunschweig, K. Saksl, J. Furste, P. Eschenbacher, F. Brunke, D. Wolter, M. Kohnke, C. Siemers, J. Kiese, M. Schlemminger

"In general, titanium alloys combine outstanding mechanical properties with corrosion resistance and biocompatibility and are, therefore, used in many challenging applications. Nevertheless, for special products, well-tailored properties are required which might not be achievable by a specific design so that new or modified alloys are needed. In this overview paper, alloy development strategies performed at the Institute for Materials of the Technische Universitat Braunschweig are discussed at different examples, namely, (1) oxidation-resistant, microstructural-stabilized and cold-workable alloys for exhaust applications, (2) aluminum- and vanadium-free, medium-strength and cold-workable alloys for implants and osteosynthesis applications and (3) free-machining alloys by the addition of particles with low melting points for non-safety critical light-weight constructions to replace heavier steels, e.g. in automotive applications. A special focus is set on the alloy development techniques and the analyses carried out to achieve well-balanced properties by the optimization of the alloy compositions. INTRODUCTIONTitanium belongs to the allotropic metals and can therefore exist in two different equilibrium lattice modifications. Pure titanium crystallizes at 1668°C in a body centered cubic (bcc) structure called ?- titanium which at 882°C transforms to a hexagonal close packed structure (hcp), the a-titanium. A martensitic ?-to-a-transformation is possible at large cooling rates. This thermally induced hexagonal martensite is called the a'-phase. The transformation temperature named ?-transus-temperature (T ?) can be influenced by alloying elements (Peters & Leyens, 2002).For titanium alloy production typical alloying elements are aluminum (Al) and oxygen (O), both a-stabilizers shifting the ?-transus temperature to higher temperatures, whereas tin (Sn) and zirconium (Zr) only show a limited influence on the ?-transus temperature. The ?-stabilizing elements are subdivided into two groups: Niobium (Nb), molybdenum (Mo) and vanadium (V) stabilize the ?-phase between the melting point and room temperature and are therefore called isomorphous -stabilizers. Elements like copper (Cu), iron (Fe) or silicon (Si) also stabilize the ?-phase to lower temperatures but undergo a eutectoid reaction during cooling. ?-titanium then dissociates to a-titanium and an intermetallic compound. Consequently, these elements are called eutectoid ?-stabilizers (Boyer, Welsh & Collings, 1994)."

Jan 1, 2016