Search Documents

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By R. A. Wyman, F. E. Hanes

THE demand for high-quality aggregate is increasing in all phases of the construction industry and in all organizations associated with road building in Canada. The production of aggregate in Canada has increased almost continuously since the end of the war and has quadrupled since 1948. Increases during the past fifteen years can be accounted for by the expansion in all types of construction, particularly that of roads and highways. Total construction in 1959, based on preliminary estimates, has been valued at $7 billion, and an increase fore-cast for 1960 indicates optimism on the •construction horizon (1). Cement produced in Canada in 1959 amounted to 6.3 million tons. This is more than 2.5 times the 1948 production. Increased cement production indicates an increased use of concrete, and thus an increased need for aggregate. Natural sand and gravel deposits are gradually being depleted.

Jan 1, 1962

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

"7.1. Glossary of the Platinum-Group Minerals7.1.1. IntroductionA glossary of the platinum-group minerals (POM) serves as a useful introduction to a chapter on their mineralogy. Earlier glossaries (Cabri, 1972, 1976) were prepared for different purposes and composed in a different manner. As for most mineralogical textbooks, from Dana's System of Mineralogy, 3rd Edition (1850) , to Fleischer's Glossary of Mineral Species (1980), this glossary is primarily a chemical classification, arranged here in two tables. Table 7.1 groups the mineralforming compounds of the six platinum-group elements (POE) according to their essential anion(s) or according to the nonPOE element in intermetallic compounds. Table 7.2 is a similar listing for the native metals and alloys of the POE. Both tables include unidentified POM considered to be bona fide new minerals requiring additional study for complete characterization and recognition (see Chapter 9*). Some information on the chemistry of the POM is given in the sections on X-ray data (7 .2) and ore microscopy (7 .3). Because the overwhelming majority of POM have been characterized by the electron microprobe, a more detailed account of representative analyses is given in Chapter 8**. The total POM listed in Tables 7.1 and 7.2 is about 100, after deleting some which would not qualify as discrete species if found today, but which are still recognized on historical grounds; e.g. iridosmine, osmiridium, platiniridium. Tables 7.1 and 7.2 also include 28 unnamed POM; included because they are considered to be probably new species (Cabri 1981 b). The referral scheme for unnamed minerals is the same as in Chapter 9. There are considerably more palladium minerals known than other POM; the proportion of total species (listed in Tables 7.1 and 7 .2) for the POE is: Pd 48%, Pt 21 o/o , Ru and Ir 9% each, Rh 8% and Os 5%. These proportions are in marked contrast to the estimated cosmic abundance, as compiled for average type C1 chondrite by Naldrett and Duke (1980): Pt 29%, Ru 20%, Pd, Ir and Os 15% each, and Rh 6%."

Jan 1, 1979

By A. D. Pittuck

Refractory minerals .containing uranium and columbium have been successfully treated at Queen's University, Kingston, to produce high-grade concentrates. Recoveries of over 90 per cent of the uranium and columbium have been obtained when treating concentrates containing euxenite, fergusonite, betafite, and pyrochlore. The processes ?consisted -of leaching the columbium with hydrofluoric acid, and the uranium with nitric acid, sulphuric acid, or sodium carbonate solutions. The leach liquors were extracted with organic solvents from which the values were stripped and precipitated, producing final products assaying 45 to 55 per cent Ob2O5 and 60 to 70 per cent U3Os.

Jan 1, 1958

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

In the last five years, new iron ore pellet plants have been built with significantly reduced air pollution levels compared to the older generation of plants. European and American pollution controls are more stringent that in China and Brazil. The recent American plants have successfully employed circulating fluidized beds for sulfur control, baghouses for particulate control, activated carbon injection for mercury and a new design of specialized low-NOx burners.

Jan 1, 2015

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By A. G. Matyas

Process improvements which have reduced the lead content of slag from the Brunswick lead blast furnace are described. Microscope examination and electron microprobe analyses, supported by the results of slag settling and viscosity tests, showed that typically about 70% of the lead in the lead blast-furnace slag was present in the form of entrained prills of metallic lead. The total lead content was found to increase with the magnetic susceptibility of the slag. Measurements in the furnace settler indicated the presence of a magnetite-rich layer between bullion and slag, arising from high magnetite levels in the slag. This layer was believed to inhibit the settling of entrained lead from the slag. Tracer tests showed that the average slag residence time in the settler was less than 2 minutes. Improvements in coke quality and sizing, which led to a reduction in the slag magnetite content, and the installation of a larger settler and a continuous Roy tapper, have all contributed to a significant decrease in the slag lead content.

Jan 1, 1977

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By Hazel Lyman Nickel

Daring to try where others had failed, Herbert and Lou Henry Hoover translated from the Latin the principal (and first) textbook on the mining and metallurgical profession, De Re Metallica, 1556, which had been in use for two centuries and then had lain dormant for 350 years in a language unreadable except by a chosen few. Thus the Hoovers enriched the English tongue with a vitally important contribution to history in the fields of mining, metallurgy, and chemistry. To them it was a joint hobby, because they were actively interested in the beginnings of the mining profession in which they had both been trained. Illuminating the years of toil to perfect this translation shone their ideal of service to humanity, since, in the Preface, they refer to their task as "a labour of love", which had to find the moments for its execution in night hours, weekends, and holidays, extending over a period of about five years. And they add: "If the work serves to strengthen the traditions of one of the most important and least recognized of the world's professions, we shall be amply repaid". While a student at Stanford University, during the years of 1891-95, Herbert Hoover had become familiar with a copy of this Latin mineralogy classic, De Re Metallica, a rare book in the private library of Dr. John C. Branner, at that time head of the department of geology and mining. Another Stanford student in geology was also examining and studying the ponderous volume of twelve 'books'. She was Miss Lou Henry, of Monterey, who graduated in 1898, and the following year became Mrs. Herbert Hoover. Interwoven through the tapestry of their life experiences gleamed the silver thread of their interest in this mediaeval Latin textbook. Just nine years lacer, the Hoovers had commenced their translation, while they were in temporary residence in London after the seething years in China under the shadow of the Boxer rebellion.

Jan 1, 1949

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By J. J. Mather

NEPHELINE SYENITE is a feldspathic rock resembling granite in texture and hardness but it is white in colour and contains appreciable quantities of the mineral nepheline, the result of a silica deficiency. It is relatively common, with known occurrences in Russia, Scandinavia, India, Canada, United States, and other parts of the world. However, the particular deposit being mined at Nephton, Ontario, by American Nepheline Limited is unique in its remarkable uniformity and low content of iron bearing minerals, both qualities essential in a ceramic raw material. The orebody is a pear-shaped mass over five miles in length, up to a mile in width, rising in three prominent ridges as much as 300 feet above the surrounding lakestudded terrain. American Nepheline holdings, consisting of 2,200 acres, comprise some 85 per cent of the total mass.

Jan 1, 1957

By W. Abdellah

Underground mine developments, such as haulage drifts and cross cuts, play a vital role in providing access to ore extraction areas for mine production. The stability of mine developments is thus of crucial importance during the life of a mine plan. Many Canadian mines use longhole mining methods or one of its variants. These methods require access to the orebody through mine developments such as haulage drifts and cross cuts on multiple levels. This paper examines the stability of mine development access intersections with respect to the planned mining sequence. A case study, the #1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario, is presented. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) was created for a development intersection situated 1.5 km below ground surface. The stability, or performance of the intersection, is evaluated in terms of the strength-to-stress ratio. The ratio threshold is set at 1.4 for temporary openings. Unsatisfactory performance is defined as a strength-to-stress ratio less than this threshold value. The performance of the intersection stability is evaluated at various modelled mining stages and the probabilistic method of analysis is then invoked to study the probability of unsatisfactory performance of the intersection. The results are presented and categorized with respect to probability, instability, and mining stage.

Aug 1, 2013

By L. Paulino, C. E. Zangiacomi, J. Yamamoto

"This paper presents the learning from Alcoa Po9os de Caldas Smelter in Brazil, after several energy restrictions resulting from the failures of three rectifier units at its power switchyard. Starting on December 27th, fuses and diodes failed in three rectifier units of Potline #1, causing a long and dangerous power interruption. Even after current was reestablished, amperage was only 70% of the line target leading to a bath freezing process that lasted for around 48 hours. The process engineering team played with several potroom parameters as pot resistance, bath and metal levels, alumina feeding and bath chemistry in an attempt to minimize impact on the potline metal output and energy consumption. As it will be illustrated, the first battle was to keep the pots running on a ""survival"" approach. After that, several changes took place on the procedures used to run at reduced current which were considered rather successful. Finally, some recommendations will be given to foresee and prevent transformers and rectifiers from undesirable failures."

Jan 1, 2006

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By D. L. Griffith

THE realization by metallurgists of the important effect that traces of impurity may have upon the properties of a metal, and their steady demand for purer and still purer metals, have made the special cools for &apos;trace&apos; analysis of increasing value. In the United States at least, spectrographic analysis is becoming the standard method for determining the impurities in zinc die-casting alloys. The Hudson Bay Mining and Smelting Company, as a producer of virtually pure zinc, uses the spectrograph to control the purity of its products, and-as the electrolytic method is employed here-to control both the impurities in the electrolyte and those &apos;trace&apos; elements, which, while they do not contaminate the zinc, have a great effect on the plating efficiency. The general plan of the laboratory is shown in Figure l; the housing for air purification, which is on the roof, is indicated by broken lines. One of the chief factors affecting the layout was the easy way in which a spectrographic assay can be spoiled by contamination. To minimize the quantity of dust tracked in, the laboratory was made separate from the general research laboratories, and an office was placed between the two. This arrangement has its drawback because of the traffic through the office, but it has effectively cut down dust. For similar reasons, the available space was subdivided into a number of small rooms, and the air currents in the laboratory were so arranged that dust would be carried where it would do least harm. Air is drawn in at the roof over a 50-kilowatt bank of Calrod heaters, through Annis air filters, by a No. 4 Sirocco fan. Most of it is forced into the spectrograph room, but some goes to the office and darkroom. The air flow is from the spectrograph room, through the plate-measuring room, into the chemical laboratory, where it is exhausted by a No. 1% Sirocco fan on the fume hood. Air can also re-circulate from the plate-measuring room back to the heater. The arrangement is such that the air in the laboratory is maintained at higher pressure than the outside air; consequently, no dirt enters through cracks about the windows and doors. A thermo-regulator holds the temperature constant within one or two degrees; only on the hottest days in summer does the temperature rise enough to affect the focus of the instrument.

Jan 1, 1940