Search Documents

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By P. Archer

The Blondeau Formation has been examined in a stratigraphic drill section at Barlow Lake. The formation contains pyroclastic flows and volcanogenic sediments throughout, but epiclastic sedimentary rocks dominate the upper parts of the section. Five distinct types of pyroclas tic flows are known in the section, as well as minor mafic lava flows. Volcanogenic sediments are commonly intercalated with the true volcanic rocks. Sedimentary rocks include fine-grained intraclastic sandstones, heterolithic sandstones and green and black shales. Interpretation of the origin and relative disposition of the volcanic and sedimentary rocks favours a model of near-emergent vulcanism in an upward shoaling environment.

Jan 1, 1984

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By J. J. McDougall

Until quite recently, the coal in the Cape Breton field was won from comparatively thick seams with light cover, and from submarine areas, and the system of mining naturally followed was pillar-and-stall. This sytem permitted of cheap extraction, and enabled production from localities where other methods could not be employed to good advantage. Thus the pillar-and-stall system, applied to conditions as stated, justified its adoption. Our working seams today, however, are practically all under heavy cover, or are moving in that direction, and with this gradual increase in cover came the increased cost of roadway maintenance. At Princess colliery, the system of pillar-and-stall was followed until roof and bottom conditions became such that further operations were unprofitable, and the longwall method was then adopted as an economic necessity. This fact should be borne in mind when operating costs of both systems are being compared. The longwall method is not held as a cure for all difficulties of heavy cover, but through it these difficulties can be overcome with less expense than by pillar-and-stall. The longwall system of mining, strictly speaking, is one by which a seam of coal is totally extracted in one operation. There are, however, many modifications of longwall, and in some cases it is difficult to determine whether certain practices should be classed as longwall or pillar-and-stall, or a combination of both.

Jan 1, 1928

By O. Espinoza Ortega, S. Song

A process scheme has been devised to improve the silver recovery and the grade of concentrates from the scavenger concentrate of a silver ore flotation circuit. Based on modal analysis studies it was found that silver sulfide minerals in the scavenger concentrate were associated as simple binary particles and finely disseminated in sulfide and non-sulfide gangues. Fine grinding of the concentrate improved the grade-recovery curve of silver to a very limited extent owing to heterocoagulation between liberated fine silver sulfides and coarse particles of gangue. This heterocoagulation phenomenon was prevented by grinding the concentrate in the presence of the dispersing reagent sodium hexametaphosphate. The silver grade-recovery curve was improved by practicing. before the conventional flotation step, a selective aggregation step for the fine silver sulfide particles using the non-polar oil kerosene, the sulthydryl collector Aerophine 3418 and conditioning the pulp under strong agitation conditions.

Jan 1, 2004

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By T. Patching

"THE FOLLOWING notes on coal mining in the Edmonton city area are based, in the main, on scattered reports and accounts as little coal mining has been done in this area for about 20 years and few people are left who were involved in what was at one time an important industry of northern Alberta. Although coal mining is not likely to be permitted in the city area itself in the future, a record of this work is warranted to indicate the ·conditions and problems that may be encountered if underground mining again is proposed in the district in the same geological formations and in similar strata. Coal mining in the Edmonton area developed with the influx of settlers in the latter part of the nineteenth century and the first part of the present century. Probably local coal was used by the Fort's blacksmith as early as 1841, and the early settlers probably were 'gopherholing' into the outcrops along the river banks by the 1870s. The first report of commercial coal mining was in 1880 when a contract was let by the Hudson's Bay Company for the provision of 300 tons. As the population in the city and northern parts of the province grew, many new mines were opened along the river and in the district, and coal was even shipped by barge to points in Saskatchewan(1 ,2) By 1909 the Department of Public Works reported that 'Edmonton stands as the second largest domestic coal producing centre in the province'. It continued to hold this position until 1942. From about 1912 to 1951 annual production from mines in the city and surrounding district ranged between 0.38 and 0.65 million tons, depending on weather, wars and strikes. Production began to decline in 1951 because of the increasing availability and consumption of natural gas which was piped into the city and then provided to other towns and rural areas in the northern part of the province. Taylor noted that between 1880 and March 1970, when the last mine within the city area closed, the total of mines and prospects within the Edmonton city area rose to 153. Most of them were small; not more than 20 produced more than a quarter of a million tonnes during their entire life, and only three produced a million tonnes or more. As described by Taylor ""within the city district workings extend discontinuously from the apex of a narrow triangle near Groat Bridge to the base of the triangle in the Clover Bar area"". The larger mines were in this latter area. Approximate locations of the old mine workings in the city are shown in Taylor's atlas. A number of other coal mines were worked in the Rabbit Hill, Big Island, St. Albert, Namao, Cardiff and Morinville districts around the city."

Jan 1, 1985

By M. Matthias

A study, part of a doctoral dissertation (Matthias, 1991), was conducted during 1987 and 1988 to establish the means by which professionals assess and maintain their competence during the various stages of their careers. The study elicited responses from fifty-nine subjects representing engineering, pharmacy and medicine (twenty subjects from engineering, nineteen from pharmacy and twenty from medicine) on their perception and assessment of continuing competence. The findings revealed a wide variation of how professionals perceived their continuing competence and the means they adopted to keep current. The implications of the study are significant for adult education practice and theory building. The author strongly believes that now, more than ever, engineers must take ownership of their careers and professional development activities. While management and supervision have a key role to play, it is the engineer, who is ultimately responsible for the scope, planning and implementation of her/ his professional development needs. An example from one high technology company will illustrate these points.

Jan 1, 1999

By J. P. Morris, J. T. Novak, E. A. Sarver

"A variety of reagents are utilized in coal preparation, but aside from performing their desired function relatively little is known about the behavior of these reagents within the processing circuits. Where exactly do reagents go once dosed? In this paper, we present preliminary results of partitioning studies on frother (i.e., MIBC) and collector (i.e., diesel) chemicals commonly used in coal flotation, and examine implications for water management (e.g., in closed-loop systems). Additionally, we discuss the usefulness of such data in predicting environmental transport and fate of chemicals – which is currently a top priority for industry.INTRODUCTIONThe purpose of coal preparation is to upgrade mined coal into more valuable products. Since coal is primarily used as a fuel source for electricity generation, product specifications are typically contracted to minimize unwanted constituents that detract from the overall heat value (e.g., ash and moisture) or that add to environmental pollution or other problems like corrosion at a power plant (e.g., sulfur) (Pitt & Millward, 1979). Failure to meet specifications results in a financial penalty for the coal producer (Szwilski, 1986), and thus preparation processes have evolved to simultaneously optimize recovery of valuable “clean” coal with rejection of mineral matter and moisture. In addition to advancements in equipment and circuitry, development and application of various chemical reagents has dramatically improved the performance of coal preparation processes.Contemporary preparation plants typically include multiple circuits that can be categorized by the size of particles they process: coarse, intermediate, and fine/ultra-fine (Figure 1). Coarse and intermediate circuits generally rely on size classification and gravity separations (e.g., dense-media cyclones), and do not require significant chemical reagents. However, fine and ultra-fine circuits often use froth flotation to separate coal from impurities, which requires chemical additives (Table 1). The primary additives include collectors, which coat the surface of the coal particles to render them (more) hydrophobic and thus more likely to attach to air bubbles and float; and frothers, which aid in the formation and stability of the froth that will accumulate the floated coal particles. Modifiers are also commonly added to flotation circuits to regulate pH in instances where coal or impurity characteristics may change water chemistries (Laskowski, 2001). Following flotation, coagulants and flocculants are often utilized in solid-liquid separations (i.e., dewatering or clarification) for coal products, and for tailings slurries prior to their disposal in impoundments. Coagulants function via double-layer compression1 to bring colloidal particles together, while flocculants promote bridging between the grouped colloids – and the combined result is enhanced sedimentation (Wills, 2006). Defoaming or anti-foaming agents may also be required to avoid fouling of dewatering operations."

Jan 1, 2012

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

By M. Mahdi Aboutalebi, Roderick I. L. Guthrie, Mihaiela Isac

"A preliminary computational fluid flow model has been developed to simulate the flow field of liquid steel in the mold region of billet mold casting. This study reports the effect of different Submerged Entry Nozzles (SEN) on the fluid flow in round and square billet, curved mold, casters. In this study, ANSYS Fluent 14.5 software was used to model the 3-D turbulent flow of liquid steel. The standard k-0 model was used to simulate turbulence in the mold region. Similarly, the species transport equations were discretized to simulate the dye injection test into the mold cavity. The behavior of flow in the mold region was validated against previous experimental work. Predicted results showed that different nozzle types plus the slight curvatures in the molds can significantly influence the flow patterns generated within the mold region, and thereby affect the finished quality of the billet products.INTRODUCTIONConventional Continuous Casting (C.C) processes are presently used to solidify more than 95% of the 1.5 billion tons of steel now produced in the world annually (World Steel in Figure, 2014). This overwhelming contribution of C.C processes for steel production is the prime motivation for this study, in order to understand and optimize the casting processes and thereby reduce internal defects and minimize energy consumption. The primary objective of all C.C processes is to maintain liquid metal purity during the casting process and to create a uniform flow within the caster so as to avoid internal and external defects. In this regard, studying fluid flows in the mold region of continuous caster has attracted many research groups, in both academia and industry, in recent years. The mold region is one of the most critical parts of the C.C. process, in which the transport phenomena associated with this region can significantly affect the quality of the final products. Thus, proper control of fluid flows within this region can be expected to greatly decrease both internal and surface defects such as Oscillation Marks (OM), inclusion entrapment, and Mold Powder Entrapment (MPE). In the casting process, the fluid flow in the mold region can be affected by a number of variables, such as; the flow control system (stopper rod or slide gate), nozzle geometry, SEN (Submerged Entry Nozzle) depth, casting speed, mold dimensions, gas injection, and the application of electromagnetic fields. One of the most influential and easily-changed fluid flows are the jets of steel issuing from the SEN. Nozzle geometries are variable, consisting of a number of exit ports, different port angles, and/or port sizes, the bottom shape of the nozzle, and the SEN immersion depth (Thomas, 2001). The SEN characteristics can markedly affect meniscus surface velocities, surface level profiles, and turbulence levels that can vary in terms of the frequency and the magnitude of their fluctuations."

Jan 1, 2016

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015

SOFCs with thin electrolyte of two types: SDC (15um) single-layer and YSZ (5um) + SDC (15um) bi-layer were fabricated by screen printing and co-firing on Ni¬YSZ cermet substrates. Using in-situ sintered Sm0.5Sr0.5CoO3 cathode the SDC-cell shows high performance at low temperature, 1180mW/cm2 peak power density around 650°C, while the YSZ+SDC bi-layer cell generates about 340mW/cm2 at 650°C, and good performance at 700-800°C with almost theoretical OCV value. Many Zr-content micro-islands were found on the SDC electrolyte surface. The influence of co-firing temperature and thin film preparation methods on the Zr-islands' appearance was investigated.

Jan 1, 2005

By A. K. Chetin, W. W. Fitkin

"The reservoirs of Mississippian Mi-dale beds and Frobisher beds found in the Weyburn field lie at the north-western termination of a broad productive belt extending 120 miles along the northeastern rim of the Williston basin. These carbonates, and inter-bedded evaporites, originated during cycles of marine transgression and regression, and were deposited as rock types characteristic of shoal, lagoon, and basinward shelf environments. The Frobisher-Alida Beds, which form a secondary reservoir to the main Midale Beds of producing zone are composed of oolit1c, fragmental-bioclastic, vugular limestone capped by an impervious dolomitic mudstone. Production is controlled by localized structural features resulting from de-positional build-up. Excellent reservoir conditions are accompanied by an active water drive. The Frobisher Evaporite, consisting of massive primary anhydrite with dolomitic veinlets, forms the floor seal for the Midale beds oil accumulation. A significant facies transition into an oolitic, bioclastic, vugular limestone characterizes this unit. Beyond the depositional margin of the evaporitic facies, marked increases in porosity and permeability of the en-tire reservoir are noted. Carbonate units overlying the areal extent of the Frobisher Evaporite exhibit a greater degree of metasomatism, dolomitization, and more abundant secondary anhydrite.Porous carbonates comprising the producing zone of the Midale beds are divided into an oolitic, fragmental bioclastic, vugular limestone, and an overlying granular marly lime-stone unit, capped, by the Midale Evaporite. Oil is accumulated in a stratigraphic trap bounded above and be-low by primary anhydrite and truncated by the post-Mississippian erosional surface. Mississippian strata dip basinward from this erosional surface in a broad homocline exhibiting only minor irregularities. Rapid lateral and vertical porosity and permeability variations are common. Localized, separated, porous lenticles contain interstitial water in areas where the Midale beds are underlain by the Frobisher Evaporite. The major portion of the field, however, is capable of water-free production. Bottom and edge waters are found in certain portions of the field. Productive limits are tentatively defined around most of the present field perimeter. A large area along foe southern edge of the field remains open to future development. Probable ultimate remaining recoverable crude oil reserves, as of September 30th, 1958, were estimated by Mc-Daniel Consultants Ltd. to be in excess of 330 million barrels."

Jan 1, 1959

By W A. Bardswich

The numerous factors associated with the prov1s1on of satisfactory air conditions in hot and humid Canadian mines are described. The main heat sources are auto-compression and the actual flow of heat from the rock. Temperatures reach 97°F at a depth of 8,100 feet. Various methods used in coping with high temperatures are described, including the use of ice stopes and heat exchangers. Moisture control, desirable air volumes and velocities, sizes of airways and methods of distribution are important considerations. A comparison of the temperatures, humidities and types of airways of two deep mines should prove useful in the design of future ventilation systems. Introduction OUTDOOR temperatures in northern Ontario vary from a low of around -40°F in winter to a high of about +90°F in summer. The average annual mean temperature over a 12-year period was +35°F, with a summer mean of 54 o and a winter mean of 16°. Because of low outdoor temperatures, a number of northern mines must heat fresh air for underground ventilation in winter; others, with high rock temperatures, are faced with a year-round cooling problem.

Jan 1, 1965

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

By Karl J. C. Harries

"7.1. INTRODUCTIONThis chapter addresses the joint venture and examines a number of general concepts of the joint venture relationship. Chapter 8 looks at some specific concepts related to the provisions of a joint venture agreement, which are equally applicable to a shareholders’ agreement or other contractual relationship. The term “joint venture” is used because the author is a common law solicitor (a matter of convenience for which apologies are offered to civil law readers), but it should be noted that, in many aspects, the legal structure of an entity is irrelevant. It is the relationship of the parties, be they venturers or shareholders, that is important, and the areas of concern are surprisingly similar (except for terminology).The details of the joint venture relationship and agreement could fill several books. Accordingly, this chapter and the next focus on selected topics that appear to have caused problems or confusion or to be the basis for disputes. And remember that, although the following discussion is in the context of a joint venture, many of the comments apply, either directly or indirectly, to virtually any common undertaking and the agreement defining it.For interest’s sake, this chapter starts with a summary of some of the earlier types of agreements and arrangements that have evolved into the joint venture agreement of today in Canada, the philosophy of their format, and the reasons for their demise.7.2. EVOLUTION OF THE CANADIAN JOINT VENTUREThe Early DaysMuch of the opening up of Canada’s north is due to exploration for and development of mines. The early discoverers were relatively free to roam and explore at will and, if they were fortunate enough to find something, they dealt with the appropriate government to acquire exploitation rights. The early interests lay in gold or silver. Workings were small, usually worked by the owner alone or with only a couple of helpers to extract the native gold or silver. If the owner wanted to move on, he could sell his property outright and use his stake to look elsewhere.As logging and mining camps were opened, the development of better roads and railways made access easier. Entrepreneurs saw the opportunity to make money by assembling large parcels of land and working them as a single operation. In order to do this, some owners who were not ready to sell out had to be convinced to do so through more attractive offers"

Jan 1, 2003

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015